Bristan Prism PM 3HWMBAS C User manual

AFTERCARE INSTRUCTIONS
Your fitting has a high quality finish and should be treated with care
to preserve the visible surfaces. All surface finishes will wear if
not cleaned correctly, the only safe way to clean your mixer is to
wipe with a soft damp cloth. Stains can be removed using washing
up liquid. All bath cleaning powders and liquids will damage the
surface of your fitting even the non-scratch cleaners.
GUARANTEE
All products are manufactured to the highest standards and a 5
year guarantee covers any defect in manufacture.
NOTE: The 5 year guarantee on the valves is invalidated if damaged
by any waterborne debris.
In the interests of continuous product development Bristan reserve
the right to alter specification as necessary.
PRODUCT CODE: PM 3HWMBAS C
TELEPHONE HELP LINE:0844 701 6273
Bristan Group Ltd
Birch Coppice Business Park
Dordon
Tamworth
Staffordshire
B78 1SG
UK
A Masco Company
Web Site: www.bristan.com
Telephone: [phone]
Facsimile: 0844 701 6275
Email: [email protected]
(FI PM 3HWMBAS) (D3)(ST)
Prism Three Hole Wall
Mounted Basin Mixer
Before starting any installation project,
consider “safety” first. Look for the “safety
note” sign and read the safety advice.
Fitting Instructions
& Contents List
Please keep these instructions for future reference
and for the ordering of spare parts.

WATER PRESSURE
This mixer is suitable for use at all supply pressures. However for
optimum use both the hot and cold supplies should be reasonably
balanced. If the fitting is installed at low pressure (tank fed), then
the minimum distance from the outlet of the nozzle to the underside
of the cold tank should be approximately 2 metres to ensure
adequate performance. This mixer should be installed in compliance
with Water Regulations. Where the supplies are unbalanced, i.e. hot
water from the cylinder tank / cold from the mains, approved check
valves must be fitted in the supply pipes.For further details contact
your Local Water Authority.
CONTENTS
1. Fixing Nut (x2)
2. Nut for Spout (x1)
3. Grub Screw (x2)
4. Washer for Spout (x1)
5. Rawl Plug (x2)
6. Olive (x2)
7. Handle Shroud (x2)
8. Handle (x2)
9. Ring for Spout (x1)
10. Flow Straightener (x1)
11. Valve –hot & cold (x2)
12. Screw (x2)
13. Mixer Body (x1)
14. Handle Spline (x2)
15. Valve Shroud (x2)
16. Spline Screw (x2)
17. Spout (x1)
18. Spout Shroud (x1)
19. Washer (x2)
20. Screw Spacer (x2)
21. Handle Cap (x2)
Please Note: In the unlikely event you find a part missing please contact our
customer Service Help line on 0844 701 6273 for immediate dispatch of part.
INSTALLATION
Prior to drilling into walls, check there are no hidden electrical wires,
cables or water supply pipes with the aid of an electronic detector.
If you use power tools do not forget to:
•Wear eye protection
•Unplug equipment after use
1. Identify all the components and check for completeness,
particularly before arranging fitting.
2. Decide on the final position of the basin mixer body (13).
3. Plumb up the hot and cold supply pipes to the required position.
4. Attach pipework to the hot and cold inlets using the nuts (12)
and olives (6).
5. Secure mixer body (13) using the screws (12), spacers (20),
washers (19) and rawl plugs (5). NOTE: Before finishing the
wall turn on water supplies to check both correct mixer
function and for leaking from connections.
6. Set fitting into wall and complete wall finish. Please note, it is
important that the spout (17) is not damaged and that sufficient
thread is left exposed to allow the spout (17) and the valve
shrouds (15) to fit.
7. Fit spout (17) and the spout washer (4);then screw on valve
shrouds (15). NOTE: Use suitable sealant on the shrouds.
8. Slide on the spout shroud (18) and attach handles (8) with
grub screws (3) and handle caps (21).
MAINTENANCE
If the fitting begins to drip:
1. Turn off the water supply.
2. Removecap (21) and grub screw (3), then remove handle (8)
by pulling from spline (14). Unscrew both shroud (7) and valve
shroud (15). The handle spline (14) may then be removed.
3. Remove valve clip and then unscrew valve (11). Once
removed, carefully clean seating and all exposed parts.
4. Replace all of the above then turn on the water supply.
5. If problem persists contact our helpline quoting a product code.