Bristan GLL RAPSNK3 C Mounting instructions

Installation Instructions
and User Guide
Gallery Rapid Boiling
3-in-1 Sink Mixer Chrome
Models Covered:
GLL RAPSNK3 C
Please keep this booklet for future
reference.
Installer, when you have read these
instructions please ensure you leave
them with the user.

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.
Contents
2
Thank you for choosing Bristan, the UK’s leading tap and shower expert.
We have designed this product to be easy to install and use. It has also been
designed and tested in the UK to all of the relevant British Standards, and
conforms to CE Regulations.
These instructions are for your guidance to a safe and successful installation,
so please read them thoroughly and retain for future reference.
We recommend the installation is carried out by a suitably qualified person
and must conform with current I.E.E Wiring Regulations (BS7671) and Building
Regulations (Part P and Part G).
Contents
• Important Safety Information 3-4
• Specification 5
• Installation Requirements 6-7
• Installation 8-9
• Preparation for Use 9
• Operation 10-11
• General Cleaning 11
• Maintenance 12-13
• Troubleshooting 14
• Notes 15

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.
Important Safety Information
3
• Please read these instructions thoroughly
and retain for future use.
• All products manufactured and supplied by
Bristan are safe provided they are installed, used
correctly and receive regular maintenance in
accordance with these instructions.
• If you are in any doubt about your ability to
install this product safely you must employ
the services of an experienced qualified
plumber/electrician.
• Warning: The Boiling Water Tank is intended
for domestic use only. Do not install the unit
outdoors or where it might be subjected to
damp or freezing conditions.
• Check the power rating of the Boiling Water Tank
is suitable for the power rating of the electrical
circuit that it is being installed on
• Check that no parts are missing or damaged on
the Boiling Water Tank or Tap as per the
instructions. If parts are missing or damaged,
do not install and contact Customer Services
• Ensure the Boiling Water Tank is installed in a
room/environment with an access point. This is
required to prevent condensation forming within
the unit. Keep away from direct sunlight.
• This Boiling Water Tank is only intended for use
with compatible Bristan Boiling Water Taps.
Using this tank with any other tap will invalidate
the guarantee.
• Do not attempt to open or modify the Boiling
Water Tank as this will invalidate the guarantee.

• The filter supplied has to be replaced every six
months for protection of your Boiling Water Tank.
Failure to do so will invalidate your guarantee.
• To protect against electric shock, do not place the
cord, plugs or Boiling Water Tank near or in water/
other liquids. Do not operate the appliance or
touch the plug with wet hands.
• Only use the power lead supplied with the product.
If the power lead is damaged, stop using
immediately and contact Customer Services for a
replacement. Do not attempt to fix as this can result
in serious injury or death.
• Do not remove the earthing terminal, reconstruct
the plug, or disassemble the main box or any
part for the power.
• The appliance must be installed vertically with
the inlet and outlet connections at the top of the
unit. Ensure that front of the unit is visible and
the touch-screen can be easily reached.
• Warning: This appliance is not intended for
use by children or persons with reduced
physical, sensory or mental capabilities or
lack of experience and knowledge; unless
they have been given supervision or
instruction concerning use of appliance in
a safe way, and understand the hazards
involved.
• Children should not play with the appliance.
Cleaning and maintenance should not be
undertaken by children without supervision.
• Turn o all controls before unplugging.
Unplug by grasping the plug, not the cable.
Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.
Important Safety Information
4

1.0
5.0
4.0
3.02.0
Pressure
BAR
0
1.0
5.0
4.0
3.02.0
Pressure
BAR
0
1.0
5.0
4.0
3.02.0
Pressure
BAR
0
1.0
5.0
4.0
3.02.0
Pressure
BAR
0
Heavy
Commercial
5°C
20°C
Light
Commercial
Maximum Static Pressure: 3.0 Bar
Inlet Water Temperatures
Min:
1.5 Bar
Min:
0.5 Bar
Max:
3.0 Bar
Max:
5.0 Bar
Working Pressures
Hot
Cold
Suitable for high pressure
systems only
7 Temperature Settings
Cold Water Supply
Flexible Tails
Min: 5°C Max: 20°C
Min: 75°C Max: 98°C
Tools You’ll Need
1/2” BSP
2.4L
Recommended Usage
Healthcare
Pack Contents
Flat-head Screwdriver Cross-head ScrewdriverPencil Drill PliersPipe & Wire Detector
Domestic Electrical Requirements
Supply Requirements
Inlet Connections Tank Capacity
IMPORTANT
Specifications
x2
x1
x1
x1
Prior to Installation
All products manufactured and supplied by Bristan are safe to use
provided they are installed, operated correctly and receive regular
maintenance in accordance with these instructions.
This product has been designed to comply with the Water Supply
(Water Fittings) Regulations 1999 and current bylaws.
For full Installation Requirements & Notes (IRN) please visit
wras.co.uk/directory.
Remove all packaging and check the contents for damage before
starting any installation.
Fitting isolation valves (not supplied) to the inlet feeds is required
as close as is practical to the inlet connections for ease of
maintenance.
Before installing this product the water supply must be
thoroughly flushed in order to remove any swarf, solder etc.
Ensure an electric socket is near the place of installation; if a
socket needs to be installed, please request the services of a
qualified electrician.
Adjustable Spanner
x3
x1
x1
230-240V AC
1.4-1.5kW
50 Hz~
IPX4 Protection
Slight
bend
90°
angle
Kinks
Curved
round Twists
The Pressure Reducing
Valve (PRV) supplied
is pre-set at 3bar and is
required on the Domestic
Cold Supply.
x1
x3
x1
x1
x1
Pipe Cutter
52°C
65°C
Hot Water Supply
Tap Only
Min: 52°C Max: 65°C
ºC
ºC
Heating
Hot
Setting
Actual
ºC
ºC
Heating
Hot
x1
Conforms to
CE Regulations
x1
x2
Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.
5
Specification

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.
Installation Requirements
25mm
Place the tank in a suitable, well ventilated
location that will not fall below 0°C.
Ensure that the tank is installed vertically on
a level surface with adequate space around the
tank. Keep away from direct sunlight.
We recommend installing a Drain Pan and waste
(not supplied) to protect against water damage
and for ease of emptying the tank.
Also ensure that the
Filter is in an easily
accessible place for
replacement purposes.
Ensure that the
tap tails and filter
connections can reach
the connection points.
Positioning the Boiling Water Tank
150mm
Setting
Actual
ºC
ºC
Heating
Hot
6

Connection Diagram
IMPORTANT
The PRV, filter and
isolation valves, are
required for optimum
performance and
maintenance of your
product
ºC
Setting
Actual
Hot
ºC
Heating
Filter Out
Filter In
Boiling Water
Supply
3-in-1 Boiling
Water Tank
Hot Supply
Cold Supply Pressure
Reducing Valve
Household Pipework
Isolation Valves
(not supplied)
(Red)
(Blue)
(O)
(I)
(C)
(H)
Boiling Handle
Tap Handle
Spout
Inlet Connections
O
I
HC
Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.
7
Installation Requirements

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.
Setting
Actual
ºC
ºC
HeatingHot
1 2
56
4
Position the
Boiling Water
Tank in a suitable
location. (See
Installation
Requirements)
Feed the pipes
through the sink
hole and place
the tap body.
Secure the tap
in place using
the fixing kit.
Attach the
connecting pipes.
Tighten the hose
clip to secure in
place. See pg7
for Guidance.
Fix the filter
mounting bracket
to the wall/surface.
Connect
the domestic hot
and cold water
supplies.
Hot
Cold
3
Ensure easy
access, and that
the connecting
pipes from the
tap and
tank can reach.
Ensure the
filter is easily
accessible
for filter
replacements
IMPORTANT
Do not tamper
with the PRV as
this will aect the
performance of
your tap.
IMPORTANT
A single check
valve on the cold
supply is required
as per IRN R150
O
I
HC
Boiling Handle
Tap Handle
Spout
8
Installation
Ensure the
tap tails
and cables
can reach
connection
points.

Installation
Preparation for Use
7 8
10
Connect the filter inlet
connections from the boiling
water tap to the filter.
Screw the hose
adaptor on to the
red Boiling Water
Tank connector.
Push on the silicon
hose trimming o
any excess. Secure
in place with the
hose clip.
Run o at least 20 litres of water from
the Boiling Water handle, resting the
system every 30 seconds.
Your Tap is now Ready for Use.
Place a jug under
the spout and
expel all air from
the system.
Check connections
for any leaks.
WARNING
Do not
turn on the
Electricity
Supply
Attach the
Filter Sump to the
Mounting Bracket.
Connect
the filter
outlet to the
blue boiling
water tank
connector.
9
IMPORTANT
Ensure the plastic
shroud covers
the silicon hose
connector. This is
a safety feature to
prevent accidental
scalding.
Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.
9
Cut the
filter pipe
tube to size

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.
Setting
Actual
ºC
ºC
Heating
Setting
Actual
ºC
ºC
Setting
Actual
ºC
ºC
Heating Hot
1
34
2
Once the
status arc
is fully
illuminated the
water will be
at the set
temperature.
Press the
Change
Temperature
Button until
your desired
temperature
setting is
displayed.
Confirm
Temperature
Setting
Current Temperature
Setting
Actual Water
Temperature
Change Temperature Setting:
Choose from 75°C, 85°C, 90°C,
95°C, 96°C, 97°C and 98°C
Start-Up/Change Temperature
On/O
Light-up Status Arc:
Flashing = Warming Up
Plug in the Power Supply.
Hold the On/O Button until
the display lights up.
Press Confirm. The status arc will
light up and move to indicate the
water is heating up.
Hot
Setting
Actual
ºC
ºC
10
Operation