Broadcom BRCM1002 User manual

Contents: Broadcom BCM94301MPL Internal 802.11b Mini PCI Card User's Guide
Broadcom BCM94301MPLInternal 802.11b Mini PCI Card User's Guide
Introduction
Completing the Setup
Using the Broadcom BCM94301MPLWireless Utility
Specifications
Regulatory Information
Troubleshooting
Glossary
Information in this document is subject to change without notice.
© Copyright 2002 Broadcom Corporation. All rights reserved.
This document is protected by copyright and distributed under licenses restricting its use, copying, distribution, and decompilation. No
part of this document may be reproduced in any form by any means without prior written authorization of Broadcom Corporation.
Documentation is provided "as is" without warranty of any kind, either express or implied, including any kind of implied or express
warranty of non-infringement or the implied warranties of merchantability or fitness for a particular purpose.
Broadcom Corporation reserves the right to make changes without further notice to any products or data herein to improve reliability,
function, or design. Information furnished by Broadcom Corporation is believed to be accurate and reliable. However, Broadcom
Corporation does not assume any liability arising out of the application or use of this information, nor the application or use of any
product or circuit described herein, neither does it convey any license under its patent rights nor the rights of others.
Broadcom, the pulse logo, and Connecting Everything are trademarks of Broadcom Corporation and/or its subsidiaries in the United
States and certain other countries. Microsoft, Windows XP, and Windows 2000 are registered trademarks of Microsoft Corporation. All
other trademarks are the property of their respective owners.
Broadcom Corporation disclaims any proprietary interest in trademarks and trade names other than its own.
Restrictions and Disclaimers
The information contained in this document, including all instructions, cautions, and regulatory approvals and certifications, is provided by the supplier and has
not been independently verified or tested by Broadcom. Broadcom cannot be responsible for damage caused as a result of either following or failing to follow
these instructions. All statements or claims regarding the properties, capabilities, speeds or qualifications of the part referenced in this document are made by
the supplier and not by Broadcom. Broadcom specifically disclaims knowledge of the accuracy, completeness or substantiation for any such statements. All
questions or comments relating to such statements or claims should be directed to the supplier.
Preliminary Release: November 2002
94306MP-UM100-D1
file:///P|/pc/My%20Documents/Working/User%20Guides/94306MP/Index.htm [11/22/2002 2:16:03 PM]

Introduction: Broadcom BCM94301MPL Mini PCI Card User's Guide
Back to Contents
Introduction: Broadcom BCM94301MPLMini PCI Card User's Guide
Before you begin
Things you should know
BCM94301MPLnetwork
Before you begin
Obtain the following information from your network administrator (if you are a home user, obtain this information from the person that
installed your wireless access point):
●Network names (SSID) of the specific wireless networks that you want to connect to.
●WEP (Wired Equivalent Privacy) key information (if any) for the networks you want to connect to.
●For Microsoft® Windows® networking, your customer name and workgroup name.
●For your network account, your user name and password.
●Your IP address (if not using a DHCP server)
Things you should know
When you start your computer, your Broadcom BCM94301MPLinternal 802.11b Mini PCI card detects certain wireless networks that are
within range. Before you can connect to these and other wireless networks, you must configure a profile for each network using the
information you obtained from your network administrator. Instructions for configuring a network profile are provided in Completing the
setup.
WEP is a security protocol for wireless local area networks (defined in the IEEE 802.11b standard) that encrypts data sent over radio
waves. The use of the WEP key is optional and can be enabled or disabled. If the network you are connecting to has enabled WEP, you
must also enable WEP in the network profile and set the WEP key to match the WEP key used by the network. Otherwise, you cannot
connect to the network.
Broadcom BCM94301MPLnetwork
The Broadcom BCM94301MPLsolution allows you to make a wireless connection to a network, as illustrated below.
file:///P|/pc/My%20Documents/Working/User%20Guides/94306MP/intro.htm (1 of 2) [11/22/2002 2:16:04 PM]

Introduction: Broadcom BCM94301MPL Mini PCI Card User's Guide
Back to top
Back to Contents
Please read copyright and trademark information.
file:///P|/pc/My%20Documents/Working/User%20Guides/94306MP/intro.htm (2 of 2) [11/22/2002 2:16:04 PM]

Completing the Setup: Broadcom BCM94301MPL Mini PCI Card User's Guide
Back to Contents
Completing the Setup: Broadcom BCM94301MPLMini PCI Card User's
Guide
NOTE—Before you begin, be sure you have the required network information from your network administrator (see Before you begin in
the Introduction section).
Configuring a network profile (Windows® 2000 environment)
Configuring a network profile (Windows® XP environment)
Configuring a network profile (Windows® 2000 environment)
Before you can connect to a wireless network, you must configure a network profile for that network on your computer using the
BCM94301MPLwireless utility. If you purchased your portable computer with the Broadcom BCM94301MPLinternal 802.11b Mini PCI
card already installed and set up at the factory, follow the network profile configuration instructions provided below. If this is not the
case, first verify that the Broadcom BCM94301MPLcard has been properly installed in your computer according to the installation
instructions. Then proceed with the following instructions for configuring your network profiles. The instructions explain how to open the
utility and how to use it to configure a network profile.
Opening the utility
1. From the desktop, click the Start button, point to Settings, and click Control Panel.
2. Double-click the BCM94301MPLWireless Utility icon .
3. If the Wireless Networks tab in the Wireless Configuration box is not on top, click the Wireless Networks tab.
file:///P|/pc/My%20Documents/Working/User%20Guides/94306MP/setup.htm (1 of 25) [11/22/2002 2:16:07 PM]

Completing the Setup: Broadcom BCM94301MPL Mini PCI Card User's Guide
You can configure a network profile for networks that are listed in the Available networks list as well as networks that are not listed.
When you have completed configuring a network profile, the network name and icon appear at the top of the Preferred networks list.
Your computer automatically connects to the network at the top of the Preferred networks list. Follow the applicable instruction set
below, based on whether or not the network is listed and whether or not the network requires a WEP key (check with your network
administrator to see if a WEP key is required). NOTE—Both the network name and the network key are case-sensitive.
●Configuring a profile for a listed network that does not require a WEP key
●Configuring a profile for a listed network that requires a WEP key
●Configuring a profile for an network that is not listed and does not require a WEP key
●Configuring a profile for an network that is not listed and requires a WEP key
Configuring a profile for a listed network that does not require a WEP key (Windows 2000
environment)
1. After opening the utility, select the network from the Available networks list and click Configure.
file:///P|/pc/My%20Documents/Working/User%20Guides/94306MP/setup.htm (2 of 25) [11/22/2002 2:16:07 PM]

Completing the Setup: Broadcom BCM94301MPL Mini PCI Card User's Guide
2. Click OK in the Wireless Network Properties box.
3. The network name and icon appear at the top of the Preferred networks list. Wait up to one minute for the network
connection to be made. Your computer is connected to the selected network when you see a blue bubble on top of the icon
for that network. If the bubble does not appear, try to access a Web page to verify that you are connected to the Internet.
file:///P|/pc/My%20Documents/Working/User%20Guides/94306MP/setup.htm (3 of 25) [11/22/2002 2:16:07 PM]

Completing the Setup: Broadcom BCM94301MPL Mini PCI Card User's Guide
Configuring a profile for a listed network that requires a WEP key (Windows 2000
environment)
1. After opening the utility, select the network from the Available networks list and click Configure.
file:///P|/pc/My%20Documents/Working/User%20Guides/94306MP/setup.htm (4 of 25) [11/22/2002 2:16:07 PM]

Completing the Setup: Broadcom BCM94301MPL Mini PCI Card User's Guide
2. Select the Data encryption (WEP enabled) box.
3. Clear the The key is provided for me automatically box.
4. Type the network key in the Network key box.
NOTE—You do not need to select the Key format or the Key length before typing the network key. These settings
automatically change to the appropriate setting as you type the network key.
5. Click OK.
file:///P|/pc/My%20Documents/Working/User%20Guides/94306MP/setup.htm (5 of 25) [11/22/2002 2:16:07 PM]

Completing the Setup: Broadcom BCM94301MPL Mini PCI Card User's Guide
6. The network name and icon appear at the top of the Preferred networks list. Wait up to one minute for the network
connection to be made. Your computer is connected to the selected network when you see a blue bubble on top of the icon
for that network. If the bubble does not appear, try to access a Web page to verify that you are connected to the Internet.
file:///P|/pc/My%20Documents/Working/User%20Guides/94306MP/setup.htm (6 of 25) [11/22/2002 2:16:07 PM]

Completing the Setup: Broadcom BCM94301MPL Mini PCI Card User's Guide
Configuring a profile for a network that is not listed and does not require a WEP key
(Windows 2000 environment)
1. After opening the utility, click Add.
file:///P|/pc/My%20Documents/Working/User%20Guides/94306MP/setup.htm (7 of 25) [11/22/2002 2:16:07 PM]