BroaMan Repeat8-NANO-4IN User manual

BROAMAN Repeat8-NANO
Operating Manual
Rev. 1.0
Operating Manual for
Repeat8-NANO
Small Converter Device
© Copyright 2017 All rights reserved
BROAMAN GmbH
Lohenstr. 8
82166 Munich-Gräfelfing
Germany

Page intentionally left blank.

Repeat8-NANO 3 / 17 rev. 1.0
Important Safety Instructions
•Please read this operating manual carefully.
•Please keep this operating manual in a safe place.
•Heed all warnings.
•Follow all instructions.
•This device may only be used in accordance to the information provided in this operating
manual. Ensure that all recommendations, especially the safety recommendations as detailed
in this operating manual, are followed before and during the usage of the device.
•Do not use this device near water, for example, in humid or damp rooms.
•Clean only with a dry cloth.
•Do not block or cover any ventilation slits. Install the device in accordance with the operating
manual.
•Do not install or place the device near a source of heat such as: radiators, power-amplifiers, or
any other heat-producing equipment.
•Protect the PSU power cord from being stepped on, crushed, pinched or damaged in any other
way. Pay special attention to plugs and sockets of the device.
•Do not place this device on an unstable table, tripod, cart, etc. The device may fall, causing
serious damage to the device.
•The device can be disconnected from the power supply by pulling the plug. These must be
freely accessible at all times. The device should be disconnected during lightning storms or
when unused for long periods of time.
•Only use attachments specified by the manufacturer.
•This device contains no user serviceable parts: only refer to authorized, qualified service
personnel for any servicing.
•Your warranty will be voided if you tamper with the internal components.

Repeat8-NANO 4 / 17 rev. 1.0
Owner Information
•Operating Manual
Please read this manual. If you call for technical support, we will assume that you have already done
so. Study the operating manual carefully in order to familiarise yourself with the device and its
operation. The operating manual contains important information on proper use of the device.
It cannot be guaranteed that this operating manual will not contain typographical mistakes or
misprints. The operating manual is regularly revised and updated.
Modifications, which serve the purpose of technical improvement of the device, may be carried out
without prior notification.
•Transport and Shipping
Always ensure careful handling of the device. The device should be transported and shipped in
shock-absorbing transport cases. If these are not available, we recommend well-padded packaging
such as the coated carton in which the device was delivered.
•Operational Environment
This device can be used in E1, E2, E3, E4, or E5 environments (as listed below) according to the
harmonized European standards EN55103-1 and EN55103-2 “Electromagnetic compatibility –
Product family standard for audio, video and audio-visual and entertainment lighting control apparatus
for professional use”
E1-Residental
E2-Commercial and light industrial
E3-Urban outdoors
E4-Controlled EMC environment e.g. broadcast and TV-studio
E5-Heavy industry
The product is intended for the use in moderate climate.
•Ventilation
Install the device in accordance to the operating manual. Allow for sufficient space around the units
and make sure to allow for air circulation near device. Do not operate the device close to heat
emitting equipment, such as power-amplifiers. Leave sufficient space (minimum ½RU) between the
device and any heat emitting devices housed in the same rack.
A BroaMan Repeat8-NANO devices can be stacked up to 4 devices when operating standard 5V
PSU originally delivered by BroaMan. When 12V 3rd party PSU is used up to 2 devices can be
stacked.
It is recommended to use Power Supply Unit delivered with the product. BroaMan takes no
responsibility for incorrect generic PSU usage.
•Water and Moisture etc.
To prevent fire or shock hazard do not expose the device to direct sunlight, dust, water or rain during
operation or storage.
Please note:
Stack up to 4 devices with the original PSU (up to 2 devices with generic PSU).
Ensure air circulation around the devices.

Repeat8-NANO 5 / 17 rev. 1.0
•Cleaning
Only use a dry linen cloth to clean the device. If the unit is very dirty, moisten a cloth using a little
water and a small amount of household detergent. Never use cleansing agents containing solvents to
clean the device.
•Operating and Storage Temperature
Operating temperature: 0°C …60°C ≡32°F …140°F; ensure proper ventilation
Storage temperature: -20°C …60°C ≡-4°F …140°F
•Power Supply
The device can be disconnected from the power supply by unplugging attached PSU from main. The
PSU plug must be freely accessible at all times. The device should be disconnected during lightning
storms or when the device is unused for a long period of time.
Power-supply cords should be routed in such a way that they are not likely to be walked on, crushed,
pinched, or damaged in any other way. Pay special attention to the plugs and the sockets of the
device.
•Fuse
There is no fuse in the device. The power supplies contain circuitry that protects the device from
overload.
•Lightning
For additional protection of this device during lightning storms, or when it is left unattended and
unused for a long period of time, disconnect the power cord. This will prevent damage to the device
due to lightning and power line surges. Disconnection from the mains power supply is only possible
by disconnecting the power plug from the mains socket.
•Eye Safety
This product is a Laser Class 1 product. It complies with IEC 60825-1, FDA 21 CFR 1040.10, and
1040.11.
Important:
It is recommended due to heat emission to use attached dedicated 5V PSU.
Device can be operated with a 12V PSU, however higher heat emission of a device
will appear. Do not stack more then two devices when operating 12V.
Important:
A damaged PSU must be replaced immediately
Important:
Wrong polarity of PSU may damage device. Please refer to the drawing on device.

Repeat8-NANO 6 / 17 rev. 1.0
•Liquids with the device
Never spill liquid of any kind on the device.
•Cables and Accessories
Only use attachments that are specified by the manufacturer of the device.
Use high quality, properly terminated, cables to connect the device. The device should only be used
with optical fibre cables that are specified for use with the devices’ optical transceivers and within the
specified power budget of the optical transceivers. When not in use, ensure that the optical
connectors on the device and the optical fibre cables are covered with the provided caps.
Do not place this device on an unstable table, tripod, cart, etc. The device may fall, which can cause
injury and serious damage to the device. Any mounting of the device should follow the
manufacturer’s instructions, and should use mounting accessories recommended by the
manufacturer of the device.
•Servicing
Do not attempt to service the device by yourself.
The device contains no user serviceable parts, components or controls. The operation of an opened
device is not permitted. Such operation can lead to damage of the device’s components due to lack
of air-flow through the device.
The device may not be serviced, altered or modified without authorization from Broaman or an
Broaman authorized distributor / dealer. Only qualified service personnel may carry out repair and
maintenance work on the device. The warranty of the device will be voided if any unauthorized
maintenance or repair work has been carried out.

Repeat8-NANO 7 / 17 rev. 1.0
CE/FCC-ConformityThis document confirms that the product Repeat8-NANO bearing the CE (Communauté
Européenne)label meets all requirements in the EMC directive 2004/108/EG laid down by the Member States
Council for adjustment of legal requirements. Furthermore the product complies with the rules and regulations of
the low-voltage directive 2006/95/EG and the Restriction of Hazardous Substances Recast Directive 2011/65/EU
(RoHS 2). This product bearing the CE label complies with the following standards, ratified by CENELEC (Comité
Européen de Normalisation Electrotechnique):
Electromagnetic compatibility – Product family standard for audio, video, audio-visual and
entertainment lighting control apparatus for professional use
EN 55103-1, Emission
EN 55103-2, Immunity
EN 60065, Safety requirements
FCC notice
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communication. Operation of this equipment in a residential area is likely to
cause harmful interference, in which case you will be required to correct the interference at his own expense.
Changes or modifications not expressly approved by Broadcast Manufactur GmbH could void the user’s authority
to operate this equipment.
Industry Canada Compliance Statement
This Class[A] digital device complies with Canadian ICES-003.
Avis de conformité à la réglementation d'Industrie Canada
Cet appareil numérique de la class[A] est conforme à la norme NMB-003 du Canada.
The authorised declaration and compatibility certification lies with the manufacturer and can be viewed on
request. Responsible as manufacturer is:
Broadcast Manufactur GmbH, Lohenstr. 8, 82166 Munich-Gräfelfing, Germany
Represented by Marc Brunke, Technical Director
N.B. The awarding of the CE label confirms the compliance with legal directives issued for the manufacturer and
marketing of electronic and electrical devices. As such the CE label is not a "seal of quality" but rather proof that
the device bearing the CE label is conform with the electromagnetic compatibility standards laid down in the
above named testing regulations.
Munich, 01.09.2017
Marc Brunke

Page intentionally left blank.

Repeat8-NANO 9 / 17 rev. 1.0
Repeat8-NANO – Digital Video Converter
Table of Contents
Important Safety Instructions.....................................................................................................................................3!
Owner Information.....................................................................................................................................................4!
Device Description ..................................................................................................................................................10!
Front Panel.............................................................................................................................................................. 11!
Repeat8-NANO-4IN!Repeat8-NANO 4OUT ........................................................................................ 11!
Rear Panel ..............................................................................................................................................................11!
Repeat8-NANO-4IN!Repeat8-NANO 4OUT ........................................................................................ 11!
Device Details .........................................................................................................................................................12!
BNC Ports ....................................................................................................................................................12!
SFP Ports.....................................................................................................................................................12!
Power Supply...............................................................................................................................................12!
Control.....................................................................................................................................................................12!
Connectors and Cables........................................................................................................................................... 13!
3G-SDI and MADI Ports...............................................................................................................................13!
Optical Connections.....................................................................................................................................13!
Power Connection........................................................................................................................................13!
Technical Specifications.......................................................................................................................................... 14!
Dimensions and Weight ..........................................................................................................................................14!
Summary of Warranty ..................................................................................................................................15!
How to Obtain Warranty Service..................................................................................................................15!
Declaration of Liability.................................................................................................................................. 15!
Package Contents................................................................................................................................................... 16!
Contact Information................................................................................................................................................. 17!

Repeat8-NANO 10 / 17 rev. 1.0
Device Description
Congratulations on your purchase of a Repeat8-NANO - 3G-SDI and AES10/MADI electrical-optical-electrical
converter. The Repeat8-NANO manual, accompanied with the device’s will quickly demonstrate the advantages
of the device and help ease your day to day workload in the broadcast and professional audio visual industry.
Repeat8-NANO is a series of electrical-optical and electrical-optical converters for 3G-SDI, AES10/MADI or other
generic coax signals, converting between coaxial and optical connections.
Repeat8-NANO devices are populated with four coax ports which can carry 3G-SDI or AES10/MADI and SFP
fibre optic transceivers (separate part). SFP modules can be easily populated after delivery.
Repeat8-NANO devices are equipped with an external PSU with a DC output of 5V.
Please note:
Repeat8-NANO package does not include fiber optic transceivers. It is highly
recommended to purchase transceivers from BroaMan.