Broan 1001 ERV User guide

03119 rev. D
Installer Manual
VENTILATION SYSTEMS
vänEE Canadian Model Numbers
1001 ERV*
1001 HRV*
2001 ERV
2001 HRV*
Broan U.S.A. Model Numbers
HRV100H
HRV200H
ERV100HC
ERV200HC
VB0065
* These products earned the ENERGY STAR®
by meeting strict energy efficiency guidelines
set by Natural Resources Canada and the
US EPA. They meet ENERGY STAR requirements
only when used in Canada.

2
Table of Contents
1. SERVICE ..................................................................................................................................3
1.1 3-D Drawing ................................................................................................................................................3
1.2 Parts Ordering Chart ..................................................................................................................................4
1.3 Technical Support........................................................................................................................................4
2. UNIT TYPE & DEFROST SETTING VS GEOGRAPHICAL LOCATION ....................................................5
3. TECHNICAL DATA ....................................................................................................................6-7
3.1 Air Distribution (Normal Operation) ............................................................................................................6
3.2 Air Distribution (Defrost Mode)....................................................................................................................6
3.3 Defrost cycle table ......................................................................................................................................6
3.4 Dimensions..................................................................................................................................................7
3.5 Controls and Furnace Link Option ..............................................................................................................7
3.6 Specifications ..............................................................................................................................................7
4. TYPICAL INSTALLATIONS..............................................................................................................8
4.1 Fully Ducted System ..................................................................................................................................8
4.2 Exhaust Ducted System
(Source Point Ventilation) ....................................................................................8
4.3 Simplified (Volume Ventilation) ....................................................................................................................8
5. INSTALLATION ......................................................................................................................9-14
5.1 Locating and Mounting the Unit ..................................................................................................................9
5.2 Planning of the Ductwork ............................................................................................................................9
5.3 Calculating the Duct Size..........................................................................................................................10
5.3.1 Example Calculation ......................................................................................................................10
5.3.2 Example of a Design for a Fully Ducted System ............................................................................10
5.4 Installing the Ductwork and Registers ......................................................................................................11
5.4.1 Fully Ducted System ......................................................................................................................11
5.4.2 Exhaust Ducted System (Source Point Ventilation) ........................................................................11
5.4.3 Simplified Installation (Volume Ventilation) ....................................................................................12
5.5 Connecting Duct to the Unit ......................................................................................................................13
5.6 Installing the Exterior Hoods ....................................................................................................................14
5.7 Connecting the Drain ................................................................................................................................14
6. CONTROL DEVICES ............................................................................................................15-16
6.1 Main Controls ............................................................................................................................................15
6.2 Optional Controls ......................................................................................................................................16
6.3 Other Features ..........................................................................................................................................16
6.4 Main and Optional Controls Available for your Unit ..................................................................................16
7. INSTALLATION OF THE CONTROLS ........................................................................................17-20
7.1 Dimensions and Specifications (Main Controls) ......................................................................................17
7.2 Installation of the Main Control ............................................................................................................17-19
7.2.1 Platinum Main Control Installation ..................................................................................................17
7.2.2 Humidity Control, DH100W, Basic, VT1W and VT2W Main Control Installation ............................18
7.2.3 Main Control Electrical Connection ................................................................................................19
7.3 Electrical Connection to Optional Controls ..............................................................................................19
7.4 Electrical Connection to the Furnace........................................................................................................20
8. WIRING DIAGRAMS ............................................................................................................21-22
9. AIR FLOW BALANCING ........................................................................................................23-24
10. OVERALL VERIFICATION ......................................................................................................25-26
10.1 Main Controls ............................................................................................................................................25
10.2 Optional Control ........................................................................................................................................26
11. MAINTENANCE / INSTRUCTIONS FOR USER ................................................................................26
12. TROUBLESHOOTING ............................................................................................................27-28
13. REFERENCES ..........................................................................................................................28

3
1.1 3-D DRAWING
6
1
2
3
4
5
7
8
910
11
12
13
14
15
16
17
18
19
20
21
22 3
23
23
24
25
26
VL0016
DAMPER ASSEMBLY (REAR VIEW)
About this Manual
This manual uses the following symbols to emphasize particular information:
NOTE: Indicates supplementary information needed to fully complete an instruction.
CAUTION
Denotes an instruction which, if not followed, may severely damage the unit and/or its components.
WARNING
!
Identifies an instruction which, if not followed, might cause serious personal injuries including possibility of death.
1. Service

4
Canada: Tel: [phone] (for distributors only)
U.S.A.: Tel: [phone]
No. Description 1001 1001 2001 2001 HRV ERV HRV ERV
HRV ERV HRV ERV 100H 100HC 200H 200HC
1 Double collar port no. 2 00866 00866 00866 00866 00866 00866 00866 00866
2 Wing nut no. 10-32 00874 00874 00874 00874 00874 00874 00874 00874
3 Balancing double collar port 02256 02256 02256 02256 02256 02256 02256 02256
4 Inlet ring 12913 12913 12913 12913 12913 12913 12913 12913
5 Top wheel 14307 03093 14308 03093 14307 03093 14308 03093
6 Electronic board V99 13507 13507 13507 13507 13508 13507 13508 13507
7 Motor assembly 13504 13555 13556 13506 13504 13555 13505 13506
8 Bottom wheel 02015 02015 03093 03093 02015 02015 03093 03093
9 Square balancing damper 12645 12645 12645 12645 12645 12645 12645 12645
10 Door latches (latch) 00886 00886 00886 00886 00886 00886 00886 00886
11 Drain connector 02418 02418 02418 02418 02418 02418 02418 02418
12 Drain gasket 0,625” D 02419 02419 02419 02419 02419 02419 02419 02419
13 Washer 5/8” ID x 1” OD 03117 03117 03117 03117 03117 03117 03117 03117
14 Nut 5/8-18 02420 02420 02420 02420 02420 02420 02420 02420
15 Recovery core 03132 03136 03133 03137 03134 03136 03135 03137
16 Door assembly 12644 12644 12644 12644 12648 12648 12648 12648
17 Door latches (keeper) 00887 00887 00887 00887 00887 00887 00887 00887
18 Hinge assembly 00672 00672 00672 00672 00672 00672 00672 00672
19 Filter 03096 03096 03097 03097 03096 03096 03097 03097
20 Switch E69 10A 01825 01825 01825 01825 01825 01825 01825 01825
21 Damper assembly no. 2 12643 12643 12649 12649 12643 12643 12649 12649
22 Plastic balancing damper 02253 02253 02253 02253 02253 02253 02253 02253
23 Damper rod 12620 12620 12620 12620 12620 12620 12620 12620
24 Double collar port no. 5 02021 02021 02021 02021 02021 02021 02021 02021
25 Damper no. 1 12459 12459 12459 12459 12459 12459 12459 12459
26 Damper actuator assembly 03124 03124 03124 03124 03124 03124 03124 03124
1.2 PARTS ORDERING CHART
1. Service (cont’d)
1.3 TECHNICAL SUPPORT (FOR ASSISTANCE)
For assistance, call on week days, 8:30 AM to 5:00 PM (Eastern Standard Time).
NOTE: Do not call these numbers for ordering parts.
Technical Support Department
Please take note that parts not listed are not available; those parts require assembly knowledge that only manufacturer can guarantee.
TO ORDER PARTS: Contact your local distributor

ANCHORAGE
WHITEHORSE
JUNEAU
HAY RIVER
YELLOWKNIFE
Prince Rupert GRANDE PRAIRIE
FORT MCMURRAY
ZONE A
FORT SMITH
EDMONTON
PRINCE ALBERT
SASKATOON
JASPER
KAMLOOPS
CALGARY
PENTICTON REGINA
LETHBRIDGE
HELENA
VICTORIA
OLYMPIA
WINNIPEG
SALEM
BOISE
BISMARCK
SALT LAKE CITY
SAULT STE MARIE
ST. PAUL
DESMOINES
MADISON
TIMMINS
HARRISBURG
SACRAMENTO
DENVER
TOPEKA
SUDBURY
TORONTO
DETROIT
INDIANAPOLIS
SANTA FE
SPRINGFIELD
OKLAHOMA CITY
PHOENIX
COLUMBUS
NASHVILLE
ATLANTA
BATON ROUGE
AUSTIN
COLUMBIA
RALEIGH
WASHINGTON
OTTAWA
NORTH BAY
VAL-DOR
CHICOUTIMI
HARTFORD
CHIBOUGAMAU
MONTRÉAL
QUEBEC
BOSTON
GOOSE BAY
LABRADOR CITY
SEPT-ILES
MATANE
GASPÉ
BATHURST
ST-JOHN HALIFAX
CHARLOTTETOWN
ST JOHN'S
ZONE C
ZONE B
ZONE D
RENO
VN0002
5
2. Unit Type and Defrost Setting vs Geographical Location
ZONE A
(HRVs only)
•
Set Extended Defrost according to section 7.2.3, point 4.
•
MODELS: 1001 HRV, 2001 HRV, HRV100H, HRV200H.
ZONE B
(HRVs only)
•
Extended Defrost setting not required (factory defrost strategy pre-set).
•
MODELS: 1001 HRV, 2001 HRV, HRV100H, HRV200H
ZONE C (HRV or ERV according to your client’s particular problems)
see ZONE C SELECTION CHART beside
•
HRV MODELS: 1001 HRV, 2001 HRV, HRV100H, HRV200H.
•
ERV MODELS: 1001 ERV, 2001 ERV, ERV100HC, ERV200HC.
ZONE D (ERVs recommended) • ERV MODELS: 1001 ERV, 2001 ERV, ERV100H, ERV200H.
SYMPTOM SOLUTION
(condensation)
Indoor air quality problem ERV and / or
Excess moisture problem ERV
and / or
Important excess moisture problem HRV
ZONE C SELECTION CHART

6
3.3 DEFROST CYCLE TABLE
3.1 AIR DISTRIBUTION (NORMAL OPERATION)
3.2 AIR DISTRIBUTION (DEFROST MODE)
3. Technical Data
VF0013
FRESH AIR
FROM
OUTSIDE
STALE AIR
FROM
BUILDING
STALE AIR
TO OUTSIDE
FRESH AIR
TO BUILDING
VF0020
STALE AIR
FROM
BUILDING
FRESH AIR
TO BUILDING
NOTE: THE UNIT PERFORMANCE CHARTS ARE LISTED ON THEIR OWN SPECIFICATION SHEETS. TO ACCESS THOSE DOCUMENTS,
VISIT: WWW.VANEE-VENTILATION.COM (CANADIAN UNITS) OR WWW.BROAN.COM (U.S.A. UNITS).
OUTSIDE TEMPERATURE DEFROST CYCLES EXTENDED DEFROST CYCLE
Celcius (°C) Fahrenheits (°F) Defrosting (min.) Operation time (min.)
between each defrost cycle Defrosting (min.) Operation time (min.) between each defrost cycle
-5
-15
-27
23
5
-17
6
6
6
32
32
20
10
10
10
30
20
15

7
13¾" (349mm)
20"
(508mm)
6" (152mm)
2½" (63mm)
30¼" (768mm)
VK0040A
19" (483mm)
20"
(508mm)
6" (152mm) 30¼" (768mm)
2½" (63mm)
VK0039A
Main controls:
• Platinum (Canada only)
• Basic (Can.) / VT1W (U.S.A.)
• VT2W (U.S.A. only)
Optional controls:
• 20-minute push-button (for HRV100H and
HRV200H models only)
• 20/40/60-minute push-button
(for all other models)
• 60-minute crank timer
• Humidity Control
Link option:
• Furnace interlock
(use with forced air systems)
3.5 CONTROLS AND FURNACE LINK OPTION
3. Technical Data (cont’d)
Models numbers
• 1001 ERV
• 1001 HRV
• HRV100H
• ERV100HC
Models numbers
• 2001 ERV
• 2001 HRV
• HRV200H
• ERV200HC
MODEL NUMBERS 1001 ERV, 1001 HRV, HRV100H, ERV100HC 2001 ERV, 2001 HRV, HRV200H, ERV200HC
Weight 65 lb (30 kg) 73 lb (33 kg)
Port diameter 6” (152 mm) 6” (152 mm)
Drain diameter 1/2” (12 mm) 1/2” (12 mm)
Installation - Chains, spring and hooks (provided with U.S.A. units)
- Straps and washers (provided with Canadian units)
Motor Speed High and low speeds factory set (optional increased low speed - BLUE wire)
Electrical Supply 120 V, 60 Hz 120 V, 60 Hz
Power consumption 150 Watts 225 Watts
3.6 SPECIFICATIONS
3.4 DIMENSIONS

8
4. Typical Installation
(Primarily for homes with radiant hot water or
electric baseboard heating. See figure 1.)
Moist, stale air is exhausted from the high humidity areas in the home, such as
bathrooms, kitchen and laundry room. Fresh air is supplied to bedrooms and
principal living areas.
If required, bathroom fans and a range hood may be used to better exhaust
stale air.
Homes with more than one level require at least one exhaust register at the
highest level.
There are three (3) common installation methods.
VH0024
Figure 1
S EE 5.4.1
FOR DETAILS
(For homes with forced air heating. See figure 2.)
Moist, stale air is exhausted from the high humidity areas in the home, such as
bathrooms, kitchen and laundry room. Fresh air is supplied to the cold air return
or the supply duct of the furnace.
If required, bathroom fans and a range hood may be used to better exhaust
stale air.
Homes with more than one level require at least one exhaust register at the
highest level.
NOTE: For this type of installation, it is not essential that the furnace blower
runs when the unit is in operation, but we recommend it.
VH0025
S EE 5.4.2
FOR DETAILS
Figure 2
(For homes with forced air heating. See figure 3 or 4.)
Fresh air and exhaust air flow through the furnace ducts which simplifies the installation.
The use of bathroom fans and a range hood is suggested to better exhaust stale air.
NOTE: For the installation type shown in figure 4, furnace blower should be running when the unit is in operation.
VH0027
Figure 3
S EE 5.4.3
FOR DETAILS
VH0026
Figure 4
S EE 5.4.3
FOR DETAILS
OR
4.1 FULLY DUCTED SYSTEM
4.2 EXHAUST DUCTED SYSTEM (SOURCE POINT VENTILATION)
4.2 SIMPLIFIED (VOLUME VENTILATION)

9
5. Installation
Choose an appropriate location for the unit:
• Within an area of the house where the temperature is above 10°C / 50°F
(basement, attic, furnace room, laundry room, etc.).
• Away from living areas (dining room, living room, bedroom), if possible.
• So as to provide easy access to the interior cabinet and to the control panel on the right hand
side of the unit.
• Close to an exterior wall, so as to limit the length of the insulated flexible duct to and from the
unit.
• Close to a drain. If no drain is close by, use a pail to collect run-off.
• Away from hot chimneys, electrical panel and other fire hazards.
• Allow for a power source (110 V standard outlet).
VD0064
Figure 6
CAUTION
Make sure the unit is level.
INSPECT THE CONTENTS OF THE BOX
• Inspect the exterior of the unit for shipping damage. Ensure that there is no damage to the door, door latches, door hinges,
dampers, duct collars, cabinet, etc.
• Inspect the interior of the unit for damage. Ensure that the fan motor assembly, recovery core, insulation, dampers, damper actuator
and drain pan are all intact.
• If the unit was damaged during shipping, contact your local distributor. (Claim must be made within 24 hours after delivery.)
• Use checklist included with the unit to ensure that no parts are missing.
WARNING
!
WARNING
!
When performing installation, servicing or cleaning the unit, it is recommended to wear safety glasses and gloves.
When applicable local regulations comprises more restrictive installation and/or certification requirements, the aforementioned
requirements prevail on those of this document and the installer agrees to conform to these at his own expenses.
5.1 LOCATING AND MOUNTING THE UNIT
For vänEE Canadian models 1001 VRE, 1001 VRC, 2001 VRE and 2001 VRC,
hang the unit to ceiling joists with washers and 4 straps (included) (see
figure 7 beside).
For Broan U.S.A. models HRV100H, HRV200H, ERV100HC, and ERV200HC,
hang the unit to ceiling joists with the 4 chains, springs and hooks (included)
(see figure 7 beside).
VD0212
Figure 7
VÄNEE CANADIAN MODELS
1001 VRE, 1001 VRC,
2001 VRE AND 2001 VRC
BROAN U.S.A. MODELS
HRV100H, HRV200H,
ERV100HC AND ERV200HC
a) Follow the instructions in Section 5.3 next page to determine the appropriate duct diameters for your system.
b) Keep it simple. Plan for a minimum number of bends and joints. Keep the length of insulated duct to a minimum.
c) Do not use wall cavities as ducts. Do not use branch lines smaller than 4” (102 mm) Ø.
d) Do not ventilate crawl spaces or cold rooms. Do not attempt to recover the exhaust air from a dryer or a range hood. This would
cause clogging of the recovery module. Use sheet metal for the kitchen exhaust duct.
e) Be sure to plan for at least one exhaust register on the highest lived-in level of the house if it has 2 floors or more.
5.2 PLANNING OF THE DUCTWORK

10
5. Installation (cont’d)
Use the table below to ensure that the ducts you intend to install will be carrying air flows at or under the recommended
values. Avoid installing ducts that will have to carry air flows near the maximum values and never install a duct if its air flow
exceeds the maximum value.
NOTE: Examples 5.3.1 and 5.3.2 use imperial measures.
The same calculation applies to metric measures.
5.3.1 Example of calculation:
Problem: My installation requires two exhaust registers (one for the kitchen, one for the bathroom). I will connect these
registers to a main duct which will connect to the unit (high speed performance value of 140 cfm). What size of duct should
I use for the main exhaust duct and for the two end branches leading to the registers? (See figure 8.)
Solution: Simplified method. (For a more detailed method of calculating duct size refer to the ASHRAE or HRAI HANDBOOK).
Main duct: Table above indicates a 6” Ø duct: Recommended air flow: 120 cfm; maximum air flow: 180 cfm. The high speed
air flow of 140 cfm is close enough to the recommended value (120) and far enough away from the maximum value (180).
Therefore a 6” Ø duct or larger is an appropriate choice for the main exhaust duct.
End branches: Each end branch will have to transport an air flow of 70 cfm (140 divided by 2). Table above indicates a 5” Ø duct:
Recommended air flow: 75 cfm; maximum air flow: 110 cfm. The high speed air flow of 70 cfm is close enough to the
recommended value (75) and far enough away from the maximum value (110). Therefore a 5” Ø duct or larger is an
appropriate choice for the 2 end branches.
NOTE: A 4ӯ duct would have been too small because the maximum acceptable value for a 4ӯ duct is 60 cfm.
5.3.2 Example of a design for a fully ducted system for a unit having a high speed performance of 222 cfm
(See figure 9).
5.3 CALCULATING THE DUCT SIZE
VI0003
END
BRANCHES
MAIN BRANCH
6ӯ140 CFM
5ӯ
70 CFM
Figure 8
140 CFM
VI0004
4” Ø
42 CFM
6” Ø
129 CFM
5” Ø
65 CFM
5” Ø
64 CFM
6” Ø
93 CFM
5”
6”
7” 7” 6”
6”
6”
4”
4”
4”
4”
7” Ø 222 CFM
7” Ø 222 CFM
4” Ø 42 CFM
6” Ø 84 CFM
6” Ø 96 CFM
6” Ø 138 CFM
Figure 9
DUCTS
DIAMETER
RECOMMANDED
AIR FLOW
MAXIMUM
AIR FLOW
4” (102 mm) 40 cfm 19 l/s 68 m³/h 60 cfm 28 l/s 102 m³/h
5” (127 mm) 75 cfm 35 l/s 127 m³/h 110 cfm 52 l/s 187 m³/h
6” (152 mm) 120 cfm 57 l/s 204 m³/h 180 cfm 85 l/s 306 m³/h
7” (178 mm) 185 cfm 87 l/s 314 m³/h 270 cfm 127 l/s 459 m³/h
8” (203 mm) 260 cfm 123 l/s 442 m³/h 380 cfm 179 l/s 645 m³/h

There are two methods for connecting the unit to the furnace:
Method 1: Supply side connection
• Cut an opening into the furnace supply duct at least 18 inches (0.5 m) from the
furnace.
• Connect this opening to the fresh air distribution port of the HRV/ERV (use metal
duct, see figure 10).
• Make sure that the HRV/ERV duct forms an elbow inside the furnace
ductwork.
• If desired, interlock (synchronize) the furnace blower operation with the HRV/ERV
operation. (See Section 7.4).
Method 2: Return side connection
• Cut an opening into the furnace return duct not less than 10 feet (3.1 m) from the
furnace (A + B).
• Connect this opening to the fresh air distribution port of the HRV/ERV (see
figure 11).
NOTE: For Method 2, it is not essential that the furnace blower runs when the HRV/ERV
is in operation, but we recommend it. If desired, synchronize the furnace
blower operation (see Section 7.4).
5.4 INSTALLING THE DUCTWORK AND REGISTERS
11
5. Installation (cont’d)
5.4.1 Fully Ducted System (as illustrated in Section 4.1)
Stale air exhaust ductwork:
• Install registers in areas where contaminants are produced: kitchen, bathrooms, laundry room, etc.
• Install registers 6 to 12 inches (152 to 305 mm) from the ceiling on an interior wall OR install them in the ceiling.
• Install the kitchen register at least 4 feet (1.2 m) from the range top.
• If possible, measure the velocity of the air flowing through the registers. If the velocity is higher than 400 ft/min. (122 m/min),
then the register type is too small. Replace with a larger one.
Fresh air distribution ductwork:
• Install registers in bedrooms, dining room, living room and basement.
• Install registers either in the ceiling or high on the walls with air flow directed towards the ceiling.
(The cooler air will then cross the upper part of the room, and mix with room air before descending to occupant level.)
• If a register must be floor installed, direct the air flow up the wall.
5.4.2 Exhaust Ducted System (Source Point Ventilation) (as illustrated in Section 4.2)
Stale air exhaust ductwork: (Same as for Fully Ducted System, described on Section 5.4.1)
Fresh air distribution:
WARNING
!
Never install a stale air exhaust register in a room where a combustion device is, such as a gas furnace, a gas
water heater or a fireplace.
VD0040
B
A
VD0041
MINIMUM 18”
(0.5 M)
METAL DUCT WITH
BACKDRAFT DAMPER
A + B = NOT LESS
THAN 10’ (3.1 M)
Figure 10
Figure 11
WARNING
!
When performing duct connection to the furnace, installation must be done in accordance with all applicable
codes and standards. Please refer to your local building code.
CAUTION
When performing connection to the furnace supply duct, this duct must be sized to support the additional airflow
produced by the HRV/ERV. Also, use a metal duct with a backdraft damper to prevent the risk of overheating
the HRV/ERV.
CAUTION
The ductwork is intended to be installed in compliance with all applicable codes.

12
5. Installation (cont’d)
5.4.3 Simplified installation (Volume Ventilation) (as illustrated in Section 4.3)
There are two methods (figures 12 and 13) for connecting the unit to the furnace:
Method 1: Return-supply Method 2: Return-return
Stale air intake:
• Cut an opening into the furnace return duct not less than 10 feet (3.1 m) from the furnace (A + B).
• Connect this opening to the stale air intake port on the HRV/ERV as shown .
Fresh air distribution: (Same instructions as for Method 1 or Method 2, Section 5.4.2).
For method 2 (return-return) make sure there is a distance of at least 3 feet (0.9 m) between both connections to the
furnace.
NOTE: For Method 1, it is not essential to synchronize the furnace blower operation with the HRV/ERV operation, but we
recommend it.
VD0043
A
B
M INIMUM 3’ (0.9 M )
Figure 12 Figure 13
CAUTION
If using Method 2, make sure the furnace blower operation is synchronized with the HRV/ERV operation! See
Section 7.4.
CAUTION
When performing connection to the furnace ducts (Method 1), these ducts must be sized to support the additional
airflow produced by the HRV/ERV. Also, the supply duct must be a metal duct with a backdraft damper to prevent
the risk of overheating HRV/ERV.
VD0042
A
B
M ETAL DUCT WITH
BACKDRAFT DAMPER
M INIMUM
18” (0.5 M)
A + B = NOT LESS
THAN 10’ (3.1 M )
A + B =
NOT LESS
THAN 10’ (3.1 M )
WARNING
!
When performing duct connection to the furnace, installation must be done in accordance with all applicable
codes and standards. Please refer to your local building code.
5.4 INSTALLING THE DUCTWORK AND REGISTERS (cont’d)

Insulated flexible duct
Use the following procedure for connecting the insulated flexible duct to the ports on the unit (exhaust to outside and fresh air from outside).
a) Pull back the insulation to expose the flexible duct.
b) Connect the interior flexible duct to the port using a duct tie.
c) Carefully seal the connection with duct tape.
d) Pull the insulation over the joint and tuck it between the inner and outer rings of the double collar.
e) Pull the vapor barrier over the insulation and over the outer ring of the double collar.
f) Apply duct tape to the joint making an airtight seal. Avoid compressing the insulation when you pull the tape tightly around the joint.
Compressed insulation loses its R value and causes water dripping due to condensation on the exterior surface of the duct.
a) b) c) d), e) f)
Rigid duct:
Use duct tape to connect the rigid ducts to the ports.
Make sure that the 2 balancing dampers are left in a fully open position
before connecting the ducts to these ports (fresh air distribution port
and stale air exhaust port as shown on figure 14).
5.5 CONNECTING DUCTS TO THE UNIT
VJ0009
CAUTION
Make sure that the vapor barrier on the insulated ducts does not tear during installation to avoid condensation
within the duct.
CAUTION
Do not use screws to connect rigid ducts to the ports.
Figure 14
VJ0001
VJ0002
VJ0003
VJ0004
VJ0005
13
5. Installation (cont’d)

Make a water trap loop in the tube
to prevent the unit from drawing
unpleasant odors from the drain
source. Make sure this loop is located
BELOW the “T” as shown. This will
prevent water from being drawn
back up into the unit in case of
negative pressure. Run the tube to
the floor drain or to an alternative
drain pipe or pail. Be sure there is a
slight slope for the run-off.
14
5.6 INSTALLING THE EXTERIOR HOODS
Choose an appropriate location for installing the exterior hoods:
• At a minimum distance of 6 feet (1.8 m) between the hoods to
avoid cross-contamination
• At a minimum distance of 18 inches (457 mm) from the ground
Make sure the intake hood is at least 6 feet (1.8 m) away from any
of the following:
• Dryer exhaust, high efficiency furnace vent, central vacuum vent
• Gas meter exhaust, gas barbecue-grill
• Any exhaust from a combustion source
• Garbage bin and any other source of contamination
Refer to figure 15 for connecting the insulated duct to the hoods.
Place the “FRESH AIR INTAKE” sticker, provided in the installation
kit, on corresponding hood. An “Anti-Gust Intake Hood” should be
installed in regions where a lot of snow is expected to fall.
CAUTION
All models require an exhaust hood with a backdraft damper. This damper closes when the unit is off and
prevents unwanted cold air from entering the house.
VD0028
EXHAUST
HOOD
OPTIONAL DUCT
LOCATION
TAPE AND DUCT TIE
CAULKING
INTAKE
HOOD
6ӯ
(152 MM)
18”
(457 MM)
18”
(457 MM)
6’
(1.8M)
6’
(1.8M)
18”
(457 MM)
Figure 15
5.7 CONNECTING THE DRAIN
VO0005A
± 12"
(± 305 mm)
± 12"
(± 305 mm)
VO0003
12
VO0011
TO DRAIN
TIE-WRAP
3
5. Installation (cont’d)
Attach the 2 plastic drain fittings to
the unit using the gaskets, washers
and nuts as shown.
Cut 2 sections of plastic tubing,
about 12” (305 mm) long and attach
them to each drain fitting. Join the 2
short sections to the “T” junction and
main tube as shown.
VD0231A
± 1”
If using a pail to collect water, locate the tube
end approximately 1” from the top of the pail in
order to prevent water from being drawn back
up into the unit.

15
VT1W model (U.S.A.)
Basic model (Canada)
6.1 MAIN CONTROLS
6. Control Devices
CONDENSATION CONTROL
AIR SUPPLY CONTROL
MIN.
MAX.
OFF
AIR
EXCHANGE
-20°C
-4°F
-5°C
23°F
5°C
41°F
C
O
M
F
O
R
T
Z
O
N
E
S
U
M
M
E
R
VC0027
VT2W model
(U.S.A.)
-20°C
-4°F
-5°C
23°F
5°C
41°F
CONDENSATION CONTROL
AIR SUPPLY CONTROL
CONDENSATION CONTROL
MAXIMUM SPEED
AIR EXCHANGE IN PROGRESS
MIN. MAX.
CONTINUOUS INTERMITTENT
20 MIN.
ON
40 MIN.
OFF
C
O
M
F
O
R
T
Z
O
N
E
S
U
M
M
E
R
VC0028
Humidity Control
Designed primarily for use with our low price HRV (Heat Recovery
Ventilator) units, the Humidity Control helps control indoor maximum
humidity level during fall, winter and spring. This control should not
be installed in a house already equipped with other main controls
(except the 3-position switch). You will find a relative humidity %
scale instead of a temperature scale meant to reduce the window
condensation problems.
3-position switch
Some model may come with a 3-position mounted switch on the
electrical box on the exterior lower right front side. It is basically an
airflow control that gives the customer the choice between the low
and high speed or the OFF (REMOTE) position. This OFF
(REMOTE) position does not deactivate the optional controls.
CAUTION
All models require a main control.
Platinum model
(Canada)
VC0104
SMART
SET
MODE
PREF
U.S.A. MODELS DH100W VT1W VT2W
CANADIAN MODELS HUMIDITY
CONTROL BASIC PLATINUM
MODES
OFF Position X X X X
Intermittent exchange (TBI) 20 ON - 40 OFF X
Intermittent exchange OR OFF (ON - OFF or ON - Recirculation) X
Low speed continuous exchange X X X
High speed continuous exchange X X X
SMART (entirely automatic mode optimizing ventilation) X
Program (programs the desired ventilation according to the period of the day) X
Recirculation (manual mode performing air recirculation inside the house) X
DETECTOR
TYPES
Humidity control (Relative humidity scale %) X
Indoor condensation control (Temperature scale) X X
Outdoor Temperature X
INDICATORS
Mode indicator X X X
Air exchange indicator X X
Condensation/Polluant control max speed indicator X
Maintenance indicator X X
Day and hour indicators X
SWITCHES
Sliding button X
Push button X X

6.4 MAIN AND OPTIONAL CONTROLS AVAILABLE FOR YOUR UNIT
6.3 OTHER FEATURES
FURNACE INTERLOCK (for forced air heating system)
The furnace fan can be interlocked so that it will run simultaneously with the ERV or HRV to ensure proper distribution of fresh air throughout
the house (see table section 6.4, to see if it is available on your unit).
PERMANENT MEMORY
Our electronic controls have a default memory feature in the event of a power outage. Even the date of the last service reminder is
maintained as a convenience to the homeowner.
NOTE: For Platinum control only, if the power failure duration is more than 4 hours, the day and hour settings must be reprogrammed.
CONTROL UPGRADES
All controls can be used on any ERV, so a Basic control can be upgraded to a Platinum (or VT1W control can be upgraded to a VT2W)
in the future (see table in Section 6.4 below for control availability according to the units).
16
LIGHTED PUSH-BUTTON REMOTE 20-MINUTE SWITCH:
This remote illuminated switch is typically installed in bathrooms, kitchen and laundry room to provide 20 minutes of high speed ventilation at
the push of a button. The switch is supplied and mounted on a white single gang wall plate. This push-button is available only for
HRV100H and HRV200H units.
20/40/60-MINUTE PUSH-BUTTON TIMER:
This remote illuminated switch is typically installed in bathrooms, kitchen and laundry room to provide 20, 40 or 60 minutes of high speed
ventilation at the push of a button. The switch is supplied and mounted on a white single gang wall plate. This push-button is not available for
HRV100H and HRV200H units.
MECHANICAL TIMER
This timer allows up to 60 minutes of high speed operation to be selected from a remote location.
6.2 OPTIONAL CONTROLS
6. Control Devices (cont’d)
MODEL
NUMBER
DH100W
HUMIDITY CONTROL
VT1W
BASIC VT2W PLATINUM 20/40/60-MINUTE
PUSH-BUTTON TIMER
20-MINUTE
PUSH-BUTTON TIMER
60-MINUTE
CRANK TIMER
FURNACE
INTERLOCK
1001 ERV X X X X INTEGRATED
ERV100HC X X X X INTEGRATED
1001 HRV X X X X INTEGRATED
2001 ERV X X X X INTEGRATED
ERV200HC X X X X INTEGRATED
2001 HRV X X X X INTEGRATED
HRV100H /
HRV200H X X X X OPTIONAL KIT
PART NO.12658
MAIN CONTROLS OPTIONAL CONTROLS

7.2 INSTALLATION OF THE MAIN CONTROL
7. Installation of the Controls
7.1 DIMENSIONS AND SPECIFICATIONS (MAIN CONTROLS)
5" (127 mm)
VC0016A
5" (127 mm)
1³/8"
(35 mm)
FRONT VIEW SIDE VIEW
HUMIDITY CONTROL, DH100W, BASIC, VT1W,
AND VT2W
VO LTAGE: 12 volts DC
DIMENSIONS:5” x 5” x 1³/8”
(127 mm x 127 mm x 35 mm)
VC0105A
1"
(26 mm)
4¼" (107 mm)
4" (102 mm)
FRONT VIEW SIDE VIEW
PLATINUM
VO LTAGE: 12 volts DC
DIMENSIONS:4¼” x 4” x 1”
(107 mm x 102 mm x 26 mm)
WARNING
Always disconnect the unit before making any connections. Failure in disconnecting power could result in
electrical shock or damage of the control or electronic module inside the unit.
CAUTION
Failure to comply with the following can cause erratic operation of the unit:
• Never install more than one optional control per unit.
• Keep control low voltage wiring at least 1 foot (305 mm) away from motors, lighting ballast, light dimming
circuit and power distribution panel. Do not route control wiring alongside house power wiring.
• Ensure the wires are securely connected.
7.2.1 Platinum Main Control Installation
4. Splice back the end of the cable to
access the 4 wires. Strip the end of
each wire. Connect each wire to its
corresponding terminal on the back
of the front module: YELLOW wire
to “Y”, RED wire to “R”, GREEN
wire to “G” and BLACK wire to “B”.
5. Reinstall the front module over the back plate.
1. Route the cable from the unit to a convenient location for the
control.
2. Detach the front module from the
mounting plate by pulling the
bottom part.
3. Run the cable (4 wires) through the
central opening of the mounting
plate and mount this plate to the
wall using screws (not included). If
needed, use wall anchors (not
included).
VC0102
VC0103
VE0173
BLACK
WIRE
YELLOW
WIRE
GREEN
WIRE
RED
WIRE
CAUTION
Be careful not to pinch wires when reinstalling the
front module on its back plate.
17
!

VC0068
HUMIDITY
CONTROL
BASIC,
VT1W AND VT2W
7.2 INSTALLATION OF THE MAIN CONTROL (CONT’D)
18
7.2.2 Humidity Control, DH100W, Basic, VT1W, and VT2W Main Controls Installation
1- Determine the location of the control. The control must be installed in a central location on the main floor. Typical locations for these
controls are kitchen, main hallways and family room.
2- Remove the button(s) and the cover plate of the control.
3- Install the control 60 inches (1.5 m) from the floor and leave a free space of at least
2 inches (5 cm) to the right of the control to allow user to slide out the control
instructions (see figure beside).
Use the template provided in the control box to position the wire hole and the screw
holes. Use the screws and the plastic anchors provided in the installation kit to secure
the control.
VC0026
Humidity Control
or VT2W BASIC or VT1W
60" (1.5 m)
2"
(5 cm)
VD0025A
4- Connect the wires to the main control.
(See figures beside)
NOTE: For HRV100H and HRV200H only:
To install VT1W, only connect GREEN and BLACK wires to main
control.
5- Make sure the instruction pull-out is in the occupant’s language. If not, turn
it to the other side (see figure beside).
6- Reinstall the cover plate and the button(s).
YRGB
VE0124
VC0061
7. Installation of the Controls (cont’d)

19
7.3 ELECTRICAL CONNECTION TO OPTIONAL CONTROLS
9
8
7
6
5
4
3
2
1
OL
OC
I
1 4 7
2 5 8
36 9
J3
MAIN PC BOARD
PUSH-BUTTON SWITCHES
(HRV100H and HRV200H :
5 switchesmaximum)
J1
0L 0C I
VE0164A
REAR VIEW
7.2 INSTALLATION OF THE MAIN CONTROL (CONT’D)
7.2.3 Main Control Electrical Connection (All models)
1- Connect the wires to their corresponding position
inside the electrical compartment. Make sure the
connections of the unit and of the control
correspond exactly. (See figure beside.)
2- Connect the optional control (if applicable) by referring to Section 7.3.
3- Do the appropriate connection to the furnace (if applicable) by referring to Section 7.4.
4- NOTE: If the unit is installed in a cold region (Zone A, as defined in Section 2), set up “extended defrost” by removing jumper JU1F
on the main circuit board inside the electrical compartment (see Section 8).
5- Plug in the unit and do the “overall verification” of the system as described in Section 10.
FFIOCOL YR GBFF IOCOL YRGB
YR GBG
B
VE0038A
FF IOCOL YRGB
GB
SWITCH
VENTILATION
Proper switch
Position
REMOTE
ARRÊT
LOW SPEED
BASSE VITESSE
HIGH SPEED
HAUTE VITESSE
VT1W
HUMIDITY
CONTROL
BASIC / VT2W / PLATINUM
7. Installation of the Controls (cont’d)

W R G Y
W
R
G
C
Y
9 8 7 6 5 4 3 2 1
UNIT CONTROL CONNECTOR
THERMOSTAT
TERMINALS
FOUR
WIRES
I OC OL Y R G BF F
J3
TWO WIRES
heating only
FURNACE
24-VOLT
TERMINAL BLOCK
TWO WIRESCOOLING SYSTEM
VE0010A
STANDARD FURNACE INTERLOCK WIRING
7.4 ELECTRICAL CONNECTION TO THE FURNACE
WRGY
W
R
Y
R
G
Y
C
J1 1
2
4
5
6
8
93
*FURNACE INTERLOCK
RELAY
NC NO
7
COM
7
THERMOSTAT
TERMINAL
Unit Control Module
4 WIRES
2 WIRES
(heating only) wiring
nuts
FURNACE
24-VOLT
TERMINAL BLOCK 2 WIRESCOOLING SYSTEM
GRAY BROWN
RED
GREEN
BLUE
9-PIN AMP PLUG
*FURNACE INTERLOCK RELAY, PART NO. 12658
VE0009A
ALTERNATE FURNACE INTERLOCK WIRING
For a furnace connected to cooling system:
On some older thermostats, energizing the “R” and “G” terminals at the furnace has the effect of energizing “Y” at the thermostat and
thereby turning on the cooling system. If you identify this type of thermostat, you must use the “alternate furnace interlock wiring”. An
additional control relay will then have to be installed.
NOTE: For HRV100H and HRV200H units, always use the “alternate furnace interlock wiring”.
WARNING
!
Never connect a 120-volt AC circuit to the terminals of the furnace interlock (standard wiring). Only use the low
voltage class 2 circuit of the furnace blower control.
20
7. Installation of the Controls (cont’d)