BROLIN Desiccant User manual

1
Specification
Model no.
BR10D
Power supply
220~240V, 50Hz
Humidity Removal capacity
9 L/day RT 30 oC , RH 80%
10 L/day RT 35 oC , RH 90%
Power consumption
TURBO (high) -730W
Electric heating element-650W
Air volume (max.)
185 m3/h
Fan (Ventilation) Speed
3
Water tank volume
5L
Working temperature range
1 ~ 32oC
Timer
1 ~ 24 hours
Continuous Drainage
Yes
Safety Device
Tip-over switch
Size (WxDxH)
340 x 232 x 511 mm
N.W.
7.5 Kg
Above is measured under RT 30 oC , RH 80%.
The data marked with * may vary for technical reasons. For greater precision,
please refer to the rating label placed on the product.
Current & Fuse : F2L250V or T2L250V
Disposal
This product should be taken to our local recycling centre for safety
treatment. Waste electrical and electronic products must not be
disposed of with household waste.

2
Where to position
Excess moisture will travel
throughout your home,
For this reason, the
dehumidifier should be
positioned, so that it can
draw this moist air
towards it from all over
the home.
When positioning the
dehumidifier, ensure that
it is placed on a level
surface and that there is a
minimum of 20 cm (8") of
space on either side of
the unit to allow for
efficient airflow.
Heater advice for Dryer
function. The distance
between air vent &
clothes must be kept at
least 40cm to avoid water
drop into machine and
cause damage.
Suitable to use in basement, kitchen, living room etc

3
Before use
Caution!
Operate this unit on a firm, flat surface to avoid water leak.
Ensure that it is kept upright at all times (including transport
and store).
Suggest to run the unit continuously for 24hrs on its first use.
Do not place on soft surfaces.
Ensure that there is at least 300mm between the sides of the
appliance and any flammable materials.
Ensure that there is at least 900mm from the top of the
appliance and any flammable materials.
The unit contains a chemical substance. The unit will emit a
chemical smell during the 1st hour of operation without any
dangerous consequences.
The unit features an anti-tip safety device that will switch the
unit off if it was tipped during operating.
Only connect the unit to a properly installed and easily
accessible socket so that you can quickly pull the plug in an
emergency.
DO NOT OBSTRUCT THE AIR INTAKES AND EXHAUSTS.
FOR INDOOR USE ONLY.
NOT FOR COMMERCIAL AND INDUSTRIAL USE.
DO NOT EXPOSE THE UNIT TO DIRECT SUNLIGHT.
DO NOT USE IN CABINET, CLOSET, BOATS, CARAVANS OR
SIMILAR LOCATIONS.
DO NOT USE THE UNIT IN BATHROOMS, SWIMMING POOLS,
WASHROOMS OR SIMILAR WET AREAS.
DO NOT USE THE UNIT CLOSE TO A BATHTUB, SHOWER,
SINK AND THE LIKE.
Do not use the appliance in locations where paint, petrol or

4
other flammable liquids are used or stored.
Do not allow the appliance to fall over when there is water in
the bucket.
AVOID THE UNIT FROM SPLASH. DO NOT LET ANY LIQUID
ENTER THE UNIT.
DO NOT PLACE A CONTAINER WITH LIQUID ON TOP OF THE
UNIT.
THE CONDENSED WATER IS NOT FOR DRINKING EITHER
FOR HUMAN OR ANIMALS.
DO NOT USE BUG SPRAYS OR OTHER FLAMMABLE
CLEANSERS ON THE UNIT.
Do not lay the cord under carpets/rugs so that you can
regularly check its condition.
DO NOT TOUCH THE PLUG OF THE UNIT WITH WET HANDS.
Never use the cord of the unit as a carrying strap.
Before moving the unit, first switch off, then unplug and empty
the water tank. Basically, it takes around 2 minutes to stop
the unit and this allows the heater to cool down.
Always unplug the unit from the mains and wait for at least
one hour before carrying out any maintenance, transport or
cleaning of the unit.
Always switch the unit off and pull the plug out of the socket:
If you are not using the unit.
Before you clean the unit.
Before you assemble the accessories.
If a fault occurs.
In the event of a storm.
AVOID OVER-TWISTING, -COILING, -PULLING THE POWER
CORD, NEVER USE NYLON OR IRON WIRE TO TIDE THE
POWER CORD.

5
DO NOT USE EXTENSION CORDS.
IF THE SUPPLY CORD IS DAMAGED, IT MUST BE REPLACED
BY AN ELECTRICIAN OR SIMILARLY QUALIFIED PERSON, TO
AVOID HAZARD.
THE MAINS SUPPLY MUST CONFORM TO THE
SPECIFICATION SHOWN ON THE RATING PLATE AT THE
BACK OF THE UNIT.
THE APPLIANCE SHALL BE INSTALLED IN ACCORDANCE
WITH NATIONAL WIRING REGULATIONS.
NEVER REACH TO RETRIEVE THE UNIT IF IT HAS FALLEN IN
WATER. IN SUCH CASE, IMMEDIATELY PULL THE PLUG.
HAVE THE UNIT CHECKED BEFORE USING IT AGAIN.
This appliance can be used by children aged from 8 ye
ars and above and persons with reduced physical, sensory
or mental capabilities or lack of experience and knowledge if they
have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
Appliances intended for indoor use (excluding laundry room).
While using DRYER mode for clothes, please keep the unit AT
LEAST 40CM away from the objects (ex. the clothes) and
ensure no water will drip into the air vent of unit.
SUGGEST TO SEND THE UNIT FOR PROFESSIONAL
MAINTENANCE PERIODICALLY.
ONLY A LICENSED PROFESSIONAL IS ALLOWED TO
DISMANTLE OR MODIFY THE APPLIANCE.
THE MACHINE IS TO BE USED ONLY FOR ITS PRESCRIBED PURPOSE.
ANY OTHER USE IS DEEMED TO BE A CASE OF MISUSE. THE

6
USER/OPERATOR, NOT THE MANUFACTUER WILL BE LIABLE FOR
ANY DAMAGE OR INJURIES OF ANY KIND CAUSED AS A RESULT OF
THIS.
DO NOT USE YOUR DESICCANT UNDER THE FOLLOWING

7
Parts

8
Programming Feature
1. FAN SPEED Indicator (Sleep,
NORM, TURBO)
2. Humidity/Timer Display Window
3. TIMER Indicator
4. AUTO button
5. AIR CLEAN Indicator
6. FAN SPEED Button
7. DRYER Indicator
8. DRY(TURBO) Button
9. Humidity Button
10. ON indicator (heat element
operation indicator)
11. Power (ON/OFF) Button
12. “Full Water” indicator
13. TIMER button
14. AIR CLEAN Button

9
FAN SPEED BUTTON 3 selections:
SLEEP (MUTE): Low fan speed with Low heat and the unit is quieter. If the
ambient humidity is less than set humidity, it will run at low fan (ventilation)
only, no heat. Note! In sleep mode, the humidity indicator in the front plate
will not light on.
NORM (standard): MEDIUM fan speed with HIGH heat setting. If the ambient
humidity is below set humidity, the unit will run at Medium fan speed only, no
heat.
TURBO: HIGH fan with HIGH Heat setting. If the ambient humidity is below
set humidity, the unit will run at HIGH fan speed only, no heat.
Indicator for the set mode will light on.
AUTO BUTTON
By pressing this button, the unit will work automatically as below:
Above 70% ….in TURBO mode.
Between 55% and 70% …. in SLEEP model.
Less than 55%, …. unit stops for 30 minutes before rechecking room humidity.
Will not restart until humidity is above 55%.
DRY (LAUNDRY) BUTTON (40% RH / high fan speed/high heat)
Suitable for drying clothes.
Set desired humidity at 40%, unit will work 8hrs continuously.
Rest for 30 minutes
If room humidity > 40%, unit work for another 8hrs.
If room humidity <40%, unit rests for another 30 minutes
The DRYER indicator will be light on
☆Under this mode, the fan speed is always fixed at HIGH speed, not adjustable.
HUMIDITY BUTTON
CO (continuous dehumidify) , 40%, 50%, 60% or 70% The set HUMIDIFY level will
show on the LED display .
Please Note:
1. After 8hrs of the heater running continuously, the unit will rest for 30 minutes
before resuming the previously selected operation.
2. If the HUMIDITY button is not set, the unit will work at the default setting:
50% RH /low fan speed/low heat.