Bromic Heating STRATOS BRAHMA 3.0 NG Troubleshooting guide

INSTALLATION, INSTRUCTION AND
SERVICE MANUAL
BROMIC FLUED INDOOR GAS HEATER
STRATOS 3.0 / 5.0 / 7.0 / 9.0
BROMIC.COM/PLUMBING
1300 276 642
A member of the Bromic Group July 2019 - V1
PRODUCT IMAGE
INSTALLATION, INSTRUCTION
AND SERVICE MANUAL
BROMIC FLUED INDOOR GAS HEATER
BROMIC BRAHMA STRATOS 3.0 / 5.0 / 7.0 / 9.0
August 2019-v1.1

Flued Indoor Gas Heater - Instruction Manual
2
July 2019 - V1
PLUMBING & GAS
2GENERAL
COMPLIANCE
    
   
   
   
  
  
RANGE

 















2GENERAL
COMPLIANCE
    
   
   
   
  
  
RANGE

 















2GENERAL
COMPLIANCE
    
   
   
   
  
  
RANGE

 















Head Ofce: 10 Phiney Place, Ingleburn, Sydney, NSW 2565 Australia
Telephone: [phone] (within Australia) or NZ 0508 276 642
Email: [email protected] Web: www.bromic.com/plumbing
Note: Bromic Plumbing Pty Ltd reserves the right to make changes to specications, parts,
components and equipment without prior notication. This Installation, operation and service manual
may not be reproduced in any form without prior written consent from Bromic Plumbing Pty Ltd.
This manual contains important information about the assembly, operation, and maintenance of
Blow Heaters. Please pay close attention to the important safety information shown
throughout this instruction manual. Any safety information will be accompanied
by the following safety alert symbols:
DANGER, WARNING, IMPORTANT
!
!
!
MODEL CODE
BRAHMA STRATOS 3.0 NG 2620970
BRAHMA STRATOS 5.0 NG 2620971
BRAHMA STRATOS 7.0 NG 2620972
BRAHMA STRATOS 9.0 NG 2620973
Flued Indoor Gas Heater - Instruction Manual
2
July 2019 - V1
PLUMBING & GAS
2GENERAL
COMPLIANCE
    
   
   
   
  
  
RANGE

 















2GENERAL
COMPLIANCE
    
   
   
   
  
  
RANGE

 















2GENERAL
COMPLIANCE
    
   
   
   
  
  
RANGE

 















Head Ofce: 10 Phiney Place, Ingleburn, Sydney, NSW 2565 Australia
Telephone: [phone] (within Australia) or NZ 0508 276 642
Email: [email protected] Web: www.bromic.com/plumbing
Note: Bromic Plumbing Pty Ltd reserves the right to make changes to specications, parts,
components and equipment without prior notication. This Installation, operation and service manual
may not be reproduced in any form without prior written consent from Bromic Plumbing Pty Ltd.
This manual contains important information about the assembly, operation, and maintenance of
Blow Heaters. Please pay close attention to the important safety information shown
throughout this instruction manual. Any safety information will be accompanied
by the following safety alert symbols:
DANGER, WARNING, IMPORTANT
!
!
!
MODEL CODE
BRAHMA STRATOS 3.0 NG 2620970
BRAHMA STRATOS 5.0 NG 2620971
BRAHMA STRATOS 7.0 NG 2620972
BRAHMA STRATOS 9.0 NG 2620973
MODEL CODE
STRATOS BRAHMA 3.0 NG 2620970
STRATOS BRAHMA 5.0 NG 2620971
STRATOS BRAHMA 7.0 NG 2620972
STRATOS BRAHMA 9.0 NG 2620973
Flued Indoor Gas Heater - Instruction Manual
2
July 2019 - V1
PLUMBING & GAS
2GENERAL
COMPLIANCE
    
   
   
   
  
  
RANGE

 















2GENERAL
COMPLIANCE
    
   
   
   
  
  
RANGE

 















2GENERAL
COMPLIANCE
    
   
   
   
  
  
RANGE

 















Head Ofce: 10 Phiney Place, Ingleburn, Sydney, NSW 2565 Australia
Telephone: [phone] (within Australia) or NZ 0508 276 642
Email: [email protected] Web: www.bromic.com/plumbing
Note: Bromic Plumbing Pty Ltd reserves the right to make changes to specications, parts,
components and equipment without prior notication. This Installation, operation and service manual
may not be reproduced in any form without prior written consent from Bromic Plumbing Pty Ltd.
This manual contains important information about the assembly, operation, and maintenance of
Blow Heaters. Please pay close attention to the important safety information shown
throughout this instruction manual. Any safety information will be accompanied
by the following safety alert symbols:
DANGER, WARNING, IMPORTANT
!
!
!
MODEL CODE
BRAHMA STRATOS 3.0 NG 2620970
BRAHMA STRATOS 5.0 NG 2620971
BRAHMA STRATOS 7.0 NG 2620972
BRAHMA STRATOS 9.0 NG 2620973

GENERAL
General informations pag.5
Safety rules pag.5
Appliance description pag.6
Identification pag.6
Structure pag.7
Technical data pag.8
Accessories pag.8
Electrical scheme pag.9
Control panel pag.10
INSTALLATION
Receiving the product pag.11
Weight and dimension pag.12
Installation: WALL FITTING or FLOOR STANDING
- Apparatus choice location pag.13
- Intake & exhaust tube fumes assemblage pag.14
-- Tube Kit Ø 32 o Ø 54 mm with unique term. (Standard) pag.16
KIT “FLOOR STANDING” support structure pag.18
KIT “PROTECTION FOR WALLS MADE OF WOOD PANELS” pag.19
Electrical collegaments pag.20
Gas connection pag.20
CUSTOMER SERVICE
Preliminary operations pag.21
First service start pag.21
Processor control box malfunction pag.22
Controls during the first & after starting service pag.22
Gas transformation pag.23
Regolation pag.24
Ordinary maintenance pag.25
Appliance clean out pag.25
Components replacement pag.26
Disassembly & reassembly of the casing pag.30
Eventual anomalies & remedies pag.30
Useful information pag.32
4GENERAL
          
        
          
 
INDEX
Flued Indoor Gas Heater - Instruction Manual
3
GENERAL
General informations pag.5
Safety rules pag.5
Appliance description pag.6
Identification pag.6
Structure pag.7
Technical data pag.8
Accessories pag.8
Electrical scheme pag.9
Control panel pag.10
INSTALLATION
Receiving the product pag.11
Weight and dimension pag.12
Installation: WALL FITTING or FLOOR STANDING
- Apparatus choice location pag.13
- Intake & exhaust tube fumes assemblage pag.14
-- Tube Kit Ø 32 o Ø 54 mm with unique term. (Standard) pag.16
KIT “FLOOR STANDING” support structure pag.18
KIT “PROTECTION FOR WALLS MADE OF WOOD PANELS” pag.19
Electrical collegaments pag.20
Gas connection pag.20
CUSTOMER SERVICE
Preliminary operations pag.21
First service start pag.21
Processor control box malfunction pag.22
Controls during the first & after starting service pag.22
Gas transformation pag.23
Regolation pag.24
Ordinary maintenance pag.25
Appliance clean out pag.25
Components replacement pag.26
Disassembly & reassembly of the casing pag.30
Eventual anomalies & remedies pag.30
Useful information pag.32
4GENERAL
          
        
          
 
INDEX
GENERAL
General informations pag.5
Safety rules pag.5
Appliance description pag.6
Identification pag.6
Structure pag.7
Technical data pag.8
Accessories pag.8
Electrical scheme pag.9
Control panel pag.10
INSTALLATION
Receiving the product pag.11
Weight and dimension pag.12
Installation: WALL FITTING or FLOOR STANDING
- Apparatus choice location pag.13
- Intake & exhaust tube fumes assemblage pag.14
-- Tube Kit Ø 32 o Ø 54 mm with unique term. (Standard) pag.16
KIT “FLOOR STANDING” support structure pag.18
KIT “PROTECTION FOR WALLS MADE OF WOOD PANELS” pag.19
Electrical collegaments pag.20
Gas connection pag.20
CUSTOMER SERVICE
Preliminary operations pag.21
First service start pag.21
Processor control box malfunction pag.22
Controls during the first & after starting service pag.22
Gas transformation pag.23
Regolation pag.24
Ordinary maintenance pag.25
Appliance clean out pag.25
Components replacement pag.26
Disassembly & reassembly of the casing pag.30
Eventual anomalies & remedies pag.30
Useful information pag.32
4
GENERAL
          
        
          
 
INDEX
GENERAL
General informations 4
Safety rules 4
Appliance description 5
Identication 5
Structure 6
Technical data 7
Accessories 7
Electrical scheme 8
Control panel 9
INSTALLATION
Receiving the product 10
Weight and dimension 11
Installation: WALL FITTING or FLOOR STANDING
- Apparatur choice location 12
- Intake & exhaust tube fumes assemblage 13
--Tube Kit 32-54 mm with unique term (Standard) 15
KIT “FLOOR STANDING” support structure 17
KIT “PROTECTION FOR WALLS MADE OF WOOD PANELS” 18
Electrical collegaments 19
Gas connection 19
CUSTOMER SERVICE
Preliminary operations 20
First service start 20
Processor control box malfunction 21
Controls during the rst & after starting service 21
Gas transformation 22
Regolation 23
Ordinary maintenance 24
Appliance clean out 24
Components replacement 25
Disassembly & reassembly of the casing 27
Eventual anomalies & remedies 27
Useful information 31

Flued Indoor Gas Heater - Instruction Manual
4
We like to remember that, products that use combustion
or electrical energy there is security rule to observe
before operating.
Do not allow children to be near the appliance.
It is prohibited to turn on an electrical device if there
is a gas smell.
In this case:
- Open windows and door.
- Close the gas tap.
- Call a Technical Service Assistance.
It is prohibited to touch the appliance with wet hand
or other parts of your body.
-Electrical Hazard: Do not touch the appliance with
wet feet or other part of your body.
It is prohibited to clean the appliance when it is run-
ning.
It is prohibited to pull, remove and wring electric
wires outside the appliance also if the electrical
supply is turned off.
It is prohibited place over the appliance, towels, tea
clothes and other could be cause of inefficiency or
also source of hazard.
It is prohibited to leave paper, plastic, or other things
of the appliance box outside within a child’s reach.
It could be potential source of hazard.
After removing the packaging, check the integrity of
the contents. In case of discrepancies, contact the
Agency that sold the appliance.
The APPLIANCE must be used as intended by the
Manufacturer and for the purpose for which it was
expressly built.
The Manufacturer disclaims any contractual and
non-contractual liability for injury to persons and ani-
mals and damage to things caused by installation,
adjustment and maintenance errors or improper
appliance use.
If the APPLIANCE is not used for a long period of
time, the following operations will have to be perfor-
med:
- position the master switch of the appliance on
"OFF"
- position the master switch of the system, if fitted, on
"OFF" or disconnect the plug from the power socket.
- close the gas tap
The appliance should be serviced at least once a
year.
This booklet is an integral part of the appliance and
must therefore be carefully looked after and
ALWAYS accompany the APPLIANCE, including
when this is sold to another user or transferred to
another system.
In case of damage or loss, ask the Area After Sales
service of the Manufacturer for another copy.
Always make sure that curtains or other objects do
not obstruct the suction filter and the room air outlet
vent.
Only connect the appliance to properly earthed
power sockets.
Only install the appliance in dry environments (pro-
tection IP 20)
The appliance must not be operated wherever there
are hazardous materials, vapours or liquids.
Install the appliance on a flat surface to prevent any
malfunction.
5
GENERAL
GENERAL INFORMATIONS
SAFETY RULES
GENERAL
General informations pag.5
Safety rules pag.5
Appliance description pag.6
Identification pag.6
Structure pag.7
Technical data pag.8
Accessories pag.8
Electrical scheme pag.9
Control panel pag.10
INSTALLATION
Receiving the product pag.11
Weight and dimension pag.12
Installation: WALL FITTING or FLOOR STANDING
- Apparatus choice location pag.13
- Intake & exhaust tube fumes assemblage pag.14
-- Tube Kit Ø 32 o Ø 54 mm with unique term. (Standard) pag.16
KIT “FLOOR STANDING” support structure pag.18
KIT “PROTECTION FOR WALLS MADE OF WOOD PANELS” pag.19
Electrical collegaments pag.20
Gas connection pag.20
CUSTOMER SERVICE
Preliminary operations pag.21
First service start pag.21
Processor control box malfunction pag.22
Controls during the first & after starting service pag.22
Gas transformation pag.23
Regolation pag.24
Ordinary maintenance pag.25
Appliance clean out pag.25
Components replacement pag.26
Disassembly & reassembly of the casing pag.30
Eventual anomalies & remedies pag.30
Useful information pag.32
4
GENERAL
          
        
          
 
INDEX
Flued Indoor Gas Heater - Instruction Manual
4
We like to remember that, products that use combustion
or electrical energy there is security rule to observe
before operating.
Do not allow children to be near the appliance.
It is prohibited to turn on an electrical device if there
is a gas smell.
In this case:
- Open windows and door.
- Close the gas tap.
- Call a Technical Service Assistance.
It is prohibited to touch the appliance with wet hand
or other parts of your body.
-Electrical Hazard: Do not touch the appliance with
wet feet or other part of your body.
It is prohibited to clean the appliance when it is run-
ning.
It is prohibited to pull, remove and wring electric
wires outside the appliance also if the electrical
supply is turned off.
It is prohibited place over the appliance, towels, tea
clothes and other could be cause of inefficiency or
also source of hazard.
It is prohibited to leave paper, plastic, or other things
of the appliance box outside within a child’s reach.
It could be potential source of hazard.
After removing the packaging, check the integrity of
the contents. In case of discrepancies, contact the
Agency that sold the appliance.
The APPLIANCE must be used as intended by the
Manufacturer and for the purpose for which it was
expressly built.
The Manufacturer disclaims any contractual and
non-contractual liability for injury to persons and ani-
mals and damage to things caused by installation,
adjustment and maintenance errors or improper
appliance use.
If the APPLIANCE is not used for a long period of
time, the following operations will have to be perfor-
med:
- position the master switch of the appliance on
"OFF"
- position the master switch of the system, if fitted, on
"OFF" or disconnect the plug from the power socket.
- close the gas tap
The appliance should be serviced at least once a
year.
This booklet is an integral part of the appliance and
must therefore be carefully looked after and
ALWAYS accompany the APPLIANCE, including
when this is sold to another user or transferred to
another system.
In case of damage or loss, ask the Area After Sales
service of the Manufacturer for another copy.
Always make sure that curtains or other objects do
not obstruct the suction filter and the room air outlet
vent.
Only connect the appliance to properly earthed
power sockets.
Only install the appliance in dry environments (pro-
tection IP 20)
The appliance must not be operated wherever there
are hazardous materials, vapours or liquids.
Install the appliance on a flat surface to prevent any
malfunction.
5
GENERAL
GENERAL INFORMATIONS
SAFETY RULES
GENERAL
General informations pag.5
Safety rules pag.5
Appliance description pag.6
Identification pag.6
Structure pag.7
Technical data pag.8
Accessories pag.8
Electrical scheme pag.9
Control panel pag.10
INSTALLATION
Receiving the product pag.11
Weight and dimension pag.12
Installation: WALL FITTING or FLOOR STANDING
- Apparatus choice location pag.13
- Intake & exhaust tube fumes assemblage pag.14
-- Tube Kit Ø 32 o Ø 54 mm with unique term. (Standard) pag.16
KIT “FLOOR STANDING” support structure pag.18
KIT “PROTECTION FOR WALLS MADE OF WOOD PANELS” pag.19
Electrical collegaments pag.20
Gas connection pag.20
CUSTOMER SERVICE
Preliminary operations pag.21
First service start pag.21
Processor control box malfunction pag.22
Controls during the first & after starting service pag.22
Gas transformation pag.23
Regolation pag.24
Ordinary maintenance pag.25
Appliance clean out pag.25
Components replacement pag.26
Disassembly & reassembly of the casing pag.30
Eventual anomalies & remedies pag.30
Useful information pag.32
4
GENERAL
          
        
          
 
INDEX
Flued Indoor Gas Heater - Instruction Manual
4
We like to remember that, products that use combustion
or electrical energy there is security rule to observe
before operating.
Do not allow children to be near the appliance.
It is prohibited to turn on an electrical device if there
is a gas smell.
In this case:
- Open windows and door.
- Close the gas tap.
- Call a Technical Service Assistance.
It is prohibited to touch the appliance with wet hand
or other parts of your body.
-Electrical Hazard: Do not touch the appliance with
wet feet or other part of your body.
It is prohibited to clean the appliance when it is run-
ning.
It is prohibited to pull, remove and wring electric
wires outside the appliance also if the electrical
supply is turned off.
It is prohibited place over the appliance, towels, tea
clothes and other could be cause of inefficiency or
also source of hazard.
It is prohibited to leave paper, plastic, or other things
of the appliance box outside within a child’s reach.
It could be potential source of hazard.
After removing the packaging, check the integrity of
the contents. In case of discrepancies, contact the
Agency that sold the appliance.
The APPLIANCE must be used as intended by the
Manufacturer and for the purpose for which it was
expressly built.
The Manufacturer disclaims any contractual and
non-contractual liability for injury to persons and ani-
mals and damage to things caused by installation,
adjustment and maintenance errors or improper
appliance use.
If the APPLIANCE is not used for a long period of
time, the following operations will have to be perfor-
med:
- position the master switch of the appliance on
"OFF"
- position the master switch of the system, if fitted, on
"OFF" or disconnect the plug from the power socket.
- close the gas tap
The appliance should be serviced at least once a
year.
This booklet is an integral part of the appliance and
must therefore be carefully looked after and
ALWAYS accompany the APPLIANCE, including
when this is sold to another user or transferred to
another system.
In case of damage or loss, ask the Area After Sales
service of the Manufacturer for another copy.
Always make sure that curtains or other objects do
not obstruct the suction filter and the room air outlet
vent.
Only connect the appliance to properly earthed
power sockets.
Only install the appliance in dry environments (pro-
tection IP 20)
The appliance must not be operated wherever there
are hazardous materials, vapours or liquids.
Install the appliance on a flat surface to prevent any
malfunction.
5
GENERAL
GENERAL INFORMATIONS
SAFETY RULES
GENERAL
General informations pag.5
Safety rules pag.5
Appliance description pag.6
Identification pag.6
Structure pag.7
Technical data pag.8
Accessories pag.8
Electrical scheme pag.9
Control panel pag.10
INSTALLATION
Receiving the product pag.11
Weight and dimension pag.12
Installation: WALL FITTING or FLOOR STANDING
- Apparatus choice location pag.13
- Intake & exhaust tube fumes assemblage pag.14
-- Tube Kit Ø 32 o Ø 54 mm with unique term. (Standard) pag.16
KIT “FLOOR STANDING” support structure pag.18
KIT “PROTECTION FOR WALLS MADE OF WOOD PANELS” pag.19
Electrical collegaments pag.20
Gas connection pag.20
CUSTOMER SERVICE
Preliminary operations pag.21
First service start pag.21
Processor control box malfunction pag.22
Controls during the first & after starting service pag.22
Gas transformation pag.23
Regolation pag.24
Ordinary maintenance pag.25
Appliance clean out pag.25
Components replacement pag.26
Disassembly & reassembly of the casing pag.30
Eventual anomalies & remedies pag.30
Useful information pag.32
4
GENERAL
          
        
          
 
INDEX
Flued Indoor Gas Heater - Instruction Manual
4
We like to remember that, products that use combustion
or electrical energy there is security rule to observe
before operating.
Do not allow children to be near the appliance.
It is prohibited to turn on an electrical device if there
is a gas smell.
In this case:
- Open windows and door.
- Close the gas tap.
- Call a Technical Service Assistance.
It is prohibited to touch the appliance with wet hand
or other parts of your body.
-Electrical Hazard: Do not touch the appliance with
wet feet or other part of your body.
It is prohibited to clean the appliance when it is run-
ning.
It is prohibited to pull, remove and wring electric
wires outside the appliance also if the electrical
supply is turned off.
It is prohibited place over the appliance, towels, tea
clothes and other could be cause of inefficiency or
also source of hazard.
It is prohibited to leave paper, plastic, or other things
of the appliance box outside within a child’s reach.
It could be potential source of hazard.
After removing the packaging, check the integrity of
the contents. In case of discrepancies, contact the
Agency that sold the appliance.
The APPLIANCE must be used as intended by the
Manufacturer and for the purpose for which it was
expressly built.
The Manufacturer disclaims any contractual and
non-contractual liability for injury to persons and ani-
mals and damage to things caused by installation,
adjustment and maintenance errors or improper
appliance use.
If the APPLIANCE is not used for a long period of
time, the following operations will have to be perfor-
med:
- position the master switch of the appliance on
"OFF"
- position the master switch of the system, if fitted, on
"OFF" or disconnect the plug from the power socket.
- close the gas tap
The appliance should be serviced at least once a
year.
This booklet is an integral part of the appliance and
must therefore be carefully looked after and
ALWAYS accompany the APPLIANCE, including
when this is sold to another user or transferred to
another system.
In case of damage or loss, ask the Area After Sales
service of the Manufacturer for another copy.
Always make sure that curtains or other objects do
not obstruct the suction filter and the room air outlet
vent.
Only connect the appliance to properly earthed
power sockets.
Only install the appliance in dry environments (pro-
tection IP 20)
The appliance must not be operated wherever there
are hazardous materials, vapours or liquids.
Install the appliance on a flat surface to prevent any
malfunction.
5
GENERAL
GENERAL INFORMATIONS
SAFETY RULES
GENERAL
General informations pag.5
Safety rules pag.5
Appliance description pag.6
Identification pag.6
Structure pag.7
Technical data pag.8
Accessories pag.8
Electrical scheme pag.9
Control panel pag.10
INSTALLATION
Receiving the product pag.11
Weight and dimension pag.12
Installation: WALL FITTING or FLOOR STANDING
- Apparatus choice location pag.13
- Intake & exhaust tube fumes assemblage pag.14
-- Tube Kit Ø 32 o Ø 54 mm with unique term. (Standard) pag.16
KIT “FLOOR STANDING” support structure pag.18
KIT “PROTECTION FOR WALLS MADE OF WOOD PANELS” pag.19
Electrical collegaments pag.20
Gas connection pag.20
CUSTOMER SERVICE
Preliminary operations pag.21
First service start pag.21
Processor control box malfunction pag.22
Controls during the first & after starting service pag.22
Gas transformation pag.23
Regolation pag.24
Ordinary maintenance pag.25
Appliance clean out pag.25
Components replacement pag.26
Disassembly & reassembly of the casing pag.30
Eventual anomalies & remedies pag.30
Useful information pag.32
4
GENERAL
          
        
          
 
INDEX
Flued Indoor Gas Heater - Instruction Manual
4
We like to remember that, products that use combustion
or electrical energy there is security rule to observe
before operating.
Do not allow children to be near the appliance.
It is prohibited to turn on an electrical device if there
is a gas smell.
In this case:
- Open windows and door.
- Close the gas tap.
- Call a Technical Service Assistance.
It is prohibited to touch the appliance with wet hand
or other parts of your body.
-Electrical Hazard: Do not touch the appliance with
wet feet or other part of your body.
It is prohibited to clean the appliance when it is run-
ning.
It is prohibited to pull, remove and wring electric
wires outside the appliance also if the electrical
supply is turned off.
It is prohibited place over the appliance, towels, tea
clothes and other could be cause of inefficiency or
also source of hazard.
It is prohibited to leave paper, plastic, or other things
of the appliance box outside within a child’s reach.
It could be potential source of hazard.
After removing the packaging, check the integrity of
the contents. In case of discrepancies, contact the
Agency that sold the appliance.
The APPLIANCE must be used as intended by the
Manufacturer and for the purpose for which it was
expressly built.
The Manufacturer disclaims any contractual and
non-contractual liability for injury to persons and ani-
mals and damage to things caused by installation,
adjustment and maintenance errors or improper
appliance use.
If the APPLIANCE is not used for a long period of
time, the following operations will have to be perfor-
med:
- position the master switch of the appliance on
"OFF"
- position the master switch of the system, if fitted, on
"OFF" or disconnect the plug from the power socket.
- close the gas tap
The appliance should be serviced at least once a
year.
This booklet is an integral part of the appliance and
must therefore be carefully looked after and
ALWAYS accompany the APPLIANCE, including
when this is sold to another user or transferred to
another system.
In case of damage or loss, ask the Area After Sales
service of the Manufacturer for another copy.
Always make sure that curtains or other objects do
not obstruct the suction filter and the room air outlet
vent.
Only connect the appliance to properly earthed
power sockets.
Only install the appliance in dry environments (pro-
tection IP 20)
The appliance must not be operated wherever there
are hazardous materials, vapours or liquids.
Install the appliance on a flat surface to prevent any
malfunction.
5
GENERAL
GENERAL INFORMATIONS
SAFETY RULES
Do not spray aerosols in the vicinity of this
appliance while it is in operation.
Do not use or store flammable materials in or
near this appliance.
Do no place articles on or against this appliance.
Do not modify this appliance.

Flued Indoor Gas Heater - Instruction Manual
5
July 2019 - V1
The appliance is identified through:
- Packed label:
A label that indicates the code and the combustion it
uses to identifies the appliance.
- Technical label:
The technical label reports the matrices numbers,
the gas prearrangement, and technical observation.
-Gas prearrangement label:
It reports the kind of gas the appliance has to use,
and if there is a transformation from one kind of gas
to another you have to change the old label.
Spare parts, or technical operation require, a
precise identification of the type of model.
If there is going to be any tampering of the technical
label, this will not consent the right identification of
the apparatus.
The appliance is a gas radiator that heat up the
atmosphere.
It has an intake of air that goes in the combustion
chamber type C.
The appliance is made with an aluminium body that
allows a high efficiency of heat; it also has a fan that
allows the dispersal of air faster in the rooms.
The appliances are arranged in factory for the func-
tion at gas methane and they can be transformed to
GPL(G30/G31) using the furnished nozzle kit.
Note: At request the apparatus can be furnished
already arranged at GPL.
It also has an electrical device that allows you to do
a series of things.
There also is a Processor Control Box (P.C.B
assy) that controls all the principals’ function of
the apparatus.
After there is the Control Panel that has other
options.
6
GENERAL
 

APPLIANCE DESCRIPTION
IDENTIFICATION

Flued Indoor Gas Heater - Instruction Manual
6
July 2019 - V1
7
GENERAL
  
 
 
 
  
     
   
  
   
 
  
  
  
   
  
  
  
  
  
  
  
   
   




 














 
STRUCTURE

Flued Indoor Gas Heater - Instruction Manual
7
July 2019 - V1
8GENERAL
TECHNICAL DATA
ACCESSORIES






°


















 





 





 

     





 
 



°











 
   


 


 


 


  
  






  
  
  



°     
     
     
         
        
    
°     
     
     
°    
         
        
    
           
           
        
        
°   
°   
        
         
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
 

 

 
 
 
 
    
    
    
    
           
           
       
      
          
 
          
          
DESCRIPTION CODE
Comando Wireless 2620980
Stratos Timer - Wireless Remote 2620981
1000mm Flue 32mm dia. (70000710) 2620982
1000mm Flue 54mm dia. (70000380) 2620983
290° Aluminium Bend 54mm dia. (70000370) 2620984
Floor Standing Kit 3.0 (233628) 2620985
Floor Standing Kit 5.0 (233629) 2620986
Floor Standing Kit 9.0 (233631) 2620987
HT Armaex 32mm (70000840) 2620988
HT Armaex 54mm (70000850) 2620989
Stratos 32mm Flue Cowl (70000466) 2620990
Stratos 32mm Flue Terminal (80006900) 2620991
Stratos 54mm Flue Terminal (80006915) 2620992
Stratos 90° Elbows 32mm (7000700) 2620993
Stratos Chimney 54mm Dia (70000740) 2620994
Stratos Flue Guard (3.0 & 5.0) (70000600) 2620995
Stratos Short Radius 90° Bend - 54mm dia (70000740) 2620996

Flued Indoor Gas Heater - Instruction Manual
8
July 2019 - V1

Flued Indoor Gas Heater - Instruction Manual
9
July 2019 - V1
10
GENERAL
CONTROL PANEL
DESCRIPTION OF DISPLAY
This type of screen simultaneously provides an
entire series of information:
- MIN operating power.
- MAX operating power.
- Wire command enabling.
- ambient temperature.
- desired ambient temperature.
- degrees centigrade unit scale.
- data transmission
DESCRIPTION OF ICONS
1 - operation at MAX power.
2 - operation at MIN power.
3 - data transmission between the device and
the Wireless command (intermittent icon).
3b - Wireless command enabled (fixed on
icon).
4 - Detected ambient temperature.
4b - Desired ambient temperature.
1 - On/Off key and device RESET
2 - Reduce temperature key (MIN 5°C)
3 - Light display
4 - Increase temperature key (MAX 35°C)
5 - Enable/disable Wireless command key

Flued Indoor Gas Heater - Instruction Manual
10
July 2019 - V1
The appliance is supplied in one cardboard package:
Contents of appliance package:
1 Appliance
1 Manual control
1 Metal template
1 Pipe KIT:
1 Adapter union
1 Suction pipe (L = 500mm)
(Ø 32mm Mod. 3.0 - 5.0)
(Ø 54mm Mod. 7.0 - 9.0)
1 exhaust pipe (L = 500mm)
(Ø 32mm Mod. 3.0 - 5.0)
(Ø 54mm Mod. 7.0 - 9.0)
1 Single outer end piece + anchors
(Ø 32mm Mod. 3.0 - 5.0)
(Ø 54mm Mod. 7.0 - 9.0)
1 Document envelope:
1 Operator's instruction booklet
1 Installer's instruction booklet
1 Gas transformation kit
1 Spare parts catalogue
1 Warranty certificate
1 Warranty labels
1 Power socket
1 Paper template
11
INSTALLER
RECEIPT OF PRODUCT

Flued Indoor Gas Heater - Instruction Manual
11
July 2019 - V1
12 INSTALLER
   



   


   


  
















WEIGHT & DIMENSION




Flued Indoor Gas Heater - Instruction Manual
12
July 2019 - V1
GENERAL INFORMATIONS
This apparatus is tin respect to the environment; the
air is intake from the outside.
-When the appliance is being installed do not use
other pieces that are not give from the manufacturer.
-Don’t let the electrical cable touch heated parts, like
the grill or the intake & exhaust tubes.
Is the installation duty to tell the owner the behaviour
to keep during the apparatus function.
-Don’t block with cloths or rug the apparatus intake &
exhaust tubes.
APPARATUS CHOICE LOCATION
Before you’re going to install the appliance, check if
there is enough space for the correct function of the
appliance.
Check if around the appliance tubes there are mate-
rials that can support the heath, second check if the
wall is made of the right material and can support the
appliance weight.
Verified if around the exhaust fumes tubes, there is
no wood or plastic but there is the right material that
can support the heath.
The material where the appliance it going to be pla-
ced has to resist the exhaust tube heath (about
180°C).
In case of low resistant wall material it’s possi-
ble to realize a cavity around the exhaust fume
tube, and insulate with strong material for the pre-
sent temperature, otherwise execute a hole with a
larger diameter at least 4 cm respect to the exhaust
fume tube.
Its prohibited settles the appliance in rooms like
bath, or showers. For this installation you need
to realize special protections that make the appara-
tus consistent to the Electrical security rules.
INSTALLATION: WALL FITTING or FLOOR STANDING
13
INSTALLER

Flued Indoor Gas Heater - Instruction Manual
13
July 2019 - V1
14
INSTALLER
INTAKE AND EXHAUST TUBE FUMES ASSEM-
BLAGE
The intake & exhaust tubes can be embedded insi-
de the wall, or in sight, they have to be protected to
avoid, risk condition. To have the apparatus in sight
it exist a spacing bar so that you can see the tubes,
we recommend that the exhaust tubes have to
have a good insulation using materials that have
also a resistant of more 200° C° (ex. HT/-
Armaflex) of temperature. Realize the holes for
fastening the tubes, after establish the hangers’
length; insert it in the right position.
Before assembling the tubes kit verifying that the
Max tube length has been respected, even the
Max loaded loss provided (See table).
   
     
    
   

 




















  




        


 
















  

  

  

  

  








Flued Indoor Gas Heater - Instruction Manual
14
FITTING THE TEMPLATE, UNION AND PIPES
To determine the position of the APPLIANCE and of
the support template (3), use the paper template
(4) provided:
- level and mark the holes (1, 2), then remove the
paper template from the wall;
- make the holes (2) for fastening the template to the
wall;
- make the centring hole (1), through the entire wall
thickness;
- make the hole for the suction and discharge pipes
using the centring hole (1);
Ø 65 mm hole for Ø 32 mm pipes or Ø 110 mm
hole for Ø 54 mm pipes.
So as not to damage the outer part of the wall to
be drilled, we suggest making the hole in two
stages: starting from the inside (A) and ending on the
outer side (B).
- remove the plate (5);
- fit the adapter union unit (6) on the template, using
the screws provided;
- cut the pipes to the thickness of the wall adding 25
mm, then eliminate the excess parts.
The cut must be perpendicular to the pipe
axis, being very careful not to deform these.
After cutting, carefully remove any burrs.
To make it easier to fit pipes with O-rings, use silico-
ne grease or a soapy solution and make sure the O-
rings do not exit from their seats.
In the event of the spacer support being used, the
template + unit + pipes must be fastened directly on
the support and the pipes must be fitted in the slots
provided on the support.
- fit and fasten the pipes (7) on the unit (6);
- level the template + unit + pipes;
- insulate the exhaust pipe (8) and fit the pipes in the
hole in the wall;
Before fastening the pipes, only for lengths
greater than 50cm, insulate the fume exhau-
st using material resistant to temperatures above
200 °C (e.g. HT/-Armaflex).
- fasten the template + unit + pipes on the wall using
the screw anchors provided (2);
Use the screw anchors most suitable for
sustaining the weight and suitable for the
material of which the wall is made and to which it
is being fastened.
15
INSTALLER

Flued Indoor Gas Heater - Instruction Manual
15
16 INSTALLER
Outside grill assemblage GP and GPu
To assemble the grill you only need the inserts, and
the steeliness steel flange.
Assemblage SDP protection
The assembling is execute in the following way:
-After you have drilled on the outside wall put the
protection (1) with mortar
-Assemblage the terminal tube with the equipment
screws
-Adapt the terminal to the tube length and grill (2)
protection between the walls.
The tube cuts have to be perpendicular being real
careful do not deform.
Kit parallel tube Ø 32/54 mm with unique terminal
(standard)
This kind of system is used when the exhaust fume
and the intake of air are next to the apparatus.
Assemblage the adapter tubes connection uni-
que terminal, from the out side.
-Insert in the wall the assembled group adapter con-
nection, angles, and curves.
Position the exhaust/intake tubes at thread outside
wall, being real careful that the short tube is always
up (exhaust tube)
-Fasten the group adepter connection to the templa-
te with the screw set.
-Insert the unique terminal until the plastic ring tou-
ches the wall.
-Mark with a punch the holes for the fastening
-Cut the terminal then make the hole for the inserts
Ø 6 mm
-Fasten the unique terminal to the wall using the
inserts Ø 6mm seeing that the exhaust tube is
toward up.
Ascertain that the adapter tubes connections
are correctly inserted. To fasten the tubes
assemblage, use silicone grease and verified that
the O-ring don’t come out from there seating.
Before you wall up the tubes, only for
lengths greater than 50cm, provide to insula-
te the exhaust fume tube with material resistant
to the 200° C° (ex. HT/-Armaflex).

1
2
Ø32
Ø54
Ø32
Ø54
Ø32
Ø54
GP
SDP
GPu

Flued Indoor Gas Heater - Instruction Manual
16
July 2019 - V1

Flued Indoor Gas Heater - Instruction Manual
17
July 2019 - V1
18
INSTALLER
MOUNTING THE “FLOOR STANDING” SUPPORT
STRUCTURE
IMPORTANT! Read and respect the general
information of INSTALLATION chap.
The support structure kit is used when the wall selec-
ted for installation is unable to support the weight of
the appliance. Thanks to this accessory, all the wei-
ght of the appliance is discharged onto the floor.
Installation
- check the contents of the KIT;
- choose the installation wall and its actual consi-
stency for making the hole (A) for the suction and
exhaust pipes;
- assemble the side brackets (1) with the template
(2), supports (6) and the adjustment screws (7) so as
to create a single structure (5);
- move the single structure up against the wall and with
the help of a spirit level, make the centre of hole (A);
- make the hole (A);
Ø 65 mm hole for Ø 32 mm pipes or Ø 110 mm
hole for Ø 54 mm pipes.
- remove the plate (3) from the template (2);
- fit the unit (4) on the template (2);
- fit and fasten the pipes (10) on the unit (4);
- fit the new unit (structure + pipes) on the frame (11)
of the appliance;
- move the appliance up against the wall and level;
- fix the appliance to the wall with suitable wall plugs
using the holes (8).
- connect the power and gas supplies;
- fit the cover (9);
FLOOR STANDING

Flued Indoor Gas Heater - Instruction Manual
18
July 2019 - V1
FITTING SILUMINA FRAME ASSEMBLY FOR
INSTALLATION ON COMBUSTIBLE OR WOODEN
WALL
This assembly is suitable for walls between 100 mm
and 500 mm thick.
- Having chosen the position for the heater in accor-
dance with the installation booklet for the heater, cut
a hole through the wall, with these dimensions: dia-
meter (A).
The hole in the wall as neatly as possible to enable
the flue assembly to be installed both straight and
level through the wall.
- Fit the silumina frame assembly to the wall, as follows:
1) Measure the wall thickness, not including the
stainless-steel plate and cut the tube (2) to length
equal to the wall thickness.
Fit the internal tube, (2) inside the opening cut in the wall.
Fit the metal plate (5) to the inside of the wall, using
the 4 screws with anchors for wooden walls provi-
ded, for fixing the plate on the wall. Fit the cut tube to
the wall working from inside the building, ensuring
that it fits within the lugs on the stainless-steel plate.
Fit the internal wall plate so that the 4 screws (1) on
it fit inside the tube.
2) Fit the external stainless - stell (3) AISI 304 to the
outside of the wall using the 4 screws, included in
the pack, if the external wall is hard stone chose
screws and anchors suitable for stone walls.
Use a water resistant compound (e.g. Secomasic or
Silastic) between the plate and the wall to prevent
rainwater reaching the interior of the wall.
PROTECTION FOR WALLS MADE OF WOOD PANELS





 

 

  





19
INSTALLER

Flued Indoor Gas Heater - Instruction Manual
19
20
INSTALLER
Check on the technical label that is on the heat
exchanger cover, for the kind of gas that the applian-
ce uses.
Use the proper gas tubes and pipe fitting. The
etching under the appliance is a 3/8" M UNI ISO 7/1.
When the gas alimentation, is on the right side
of the appliance for eventuating any problems
use a nipples.
After the gas connection is done, do the first
seal tests.
GAS CONNECTION
This apparatus is equipped with a cable with plug for
connection to the mains power supply.
A proper earth connection is mandatory.
The manufacturer of the appliance cannot be held
liable for any damage caused by lack of proper earth
connection.
For jobs of an electrical nature, always refer to the
diagram attached to this booklet.
Never use gas and/or water pipes to earth the
appliance.
POWER CONNECTIONS

Flued Indoor Gas Heater - Instruction Manual
20
July 2019 - V1
The appliance is furnished and preset for the gas
function (G 20) and regulated in factory.
Note: the apparatus can also be requested with the
GPL gas function.
First things to do before you start the appliance check:
- If the appliance is preset for the right gas
- The gas connection is correctly realized and the
gas switch is opened.
- The electrical connections are properly done.
Remember it is also important to realize a good
ground connection and to respect the neutral phase.
During the first start, could be emissions of
vapors and odors annoying non dangerous. To
avoid these inconveniences, it is recommended to
run the unit at full power for several hours and ven-
tilate the room.
For greater comfort in the heated environment, we
advise using the humidifier tray (1) encased in the
casing.
Do not fill the tray to the top to prevent
water overflowing with consequent damage
to or malfunction of the appliance.
Only fill the tray with water. Avoid all other
liquids that could damage the tray or cause
appliance malfunctions.
After performing all the preparation operations for ini-
tial start-up, to start the appliance:
- make sure the fuel tap is open;
- plug into the power supply socket;
- move the master switch (if fitted) to "on" or fit the
power plug in the wall socket;
- press the On/Off key (see User section) to switch
on the appliance;
- set the room thermostat at a high value to reduce
heating time;
After startup, the appliance runs until it reaches the
set room temperature.
In case of malfunctions in startup procedure or ope-
ration, the appliance STOPS and the relevant
unblock signal lights up on the display. Reset the
appliance by keeping the unblock button pressed.
Wait until the startup procedure is completed and the
operation signal lights up.
- When the appliance is running, set the clock and
the timer for automatic operation (see User section).
FIRST SERVICE START
PRELIMINARY OPERATIONS

21
CUSTOMER SERVICE