Brother Laura Ashley Innov-ís NX2000 User manual

Bobbin work kit
Operation Manual

1
BEFORE YOU START
Thank you for choosing our product. This manual describes the procedures for sewing bobbin work. For specific
details on operating the machine, refer to the Operation Manual provided with your machine. The images and
patterns used in this manual are for illustration purposes and may differ from the actual items.
This is a kit used for sewing (utility stitches, decorative stitches or free-motion sewing). This kit cannot be used for
machine embroidering.
CONTENTS
ABOUT BOBBIN WORK ........................................................................................................... 2
INCLUDED ACCESSORIES ........................................................................................................ 2
PREPARING FOR BOBBIN WORK ............................................................................................ 3
Required Materials ................................................................................................................ 3
Upper Threading................................................................................................................... 4
Preparing the Bobbin Thread................................................................................................. 4
CREATING BOBBIN WORK ...................................................................................................... 8
Positioning the Fabric and Sewing......................................................................................... 8
Finishing the thread ends..................................................................................................... 10
Bobbin Work Free-Motion Sewing ...................................................................................... 11
Templates for Free-Motion Sewing ...................................................................................... 12
ADJUSTING THE THREAD TENSION...................................................................................... 13
Adjusting the Upper Thread Tension ................................................................................... 13
Adjusting the Tension of the Bobbin Thread........................................................................ 13
TROUBLESHOOTING............................................................................................................. 14

2
ABOUT BOBBIN WORK
You can create designs, which gives a three-dimensional appearance to the surface of the fabric, by winding the
bobbin with heavy weight thread or ribbon too thick to be fed through the sewing machine needle and sewing on
the wrong side of the fabric.
Bobbin work is sewn using the special bobbin case (gray) and bobbin cover with tabs included with this kit.
INCLUDED ACCESSORIES
Utility stitches
Decorative stitches
(For models with built-in
decorative stitches)
Free-motion sewing
1. 2. 3. 4.
Bobbin case (gray)
(XE8298-001)
Bobbin cover with tabs
(*See Note.)
Screwdriver (small)
(X55468-051)
CD-ROM (Contains the Operation
Manual and the Templates for free-
motion sewing.)
(USA/CANADA: XE9382-001,
Other areas: XE9501-001)
Note
• Two bobbin covers may be included, depending on the country or region
where this kit was purchased. Use the bobbin cover with the same shape as
the bobbin cover included with your machine. The bobbin cover with a shape
different than that included with your machine cannot be installed on the
machine. (XE8992-001) (XE8878-001)

3
PREPARING FOR BOBBIN WORK
Required Materials
■Bobbin case and bobbin cover
aBobbin case (gray)
This bobbin case is only for bobbin work. The bobbin
case will allow you to sew with thick thread or narrow
ribbon that cannot be inserted through the eye of the
needle. There is a notch at the location indicated by the
letter “A”.
bBobbin cover with tabs (for bobbin work)*
There are ribs “B” on the back of the bobbin cover.
The ribs press down on the bobbin so it is not lifted out
when thick thread is being fed from it.
This bobbin cover can also be used with normal
sewing.
* Two bobbin covers may be included, depending on the
country or region where this kit was purchased. Use the
bobbin cover with the same shape as the bobbin cover
included with your machine. The bobbin cover with a
shape different than that included with your machine
cannot be installed on the machine.
■Lower thread
We recommend the following types of threads for
bobbin work.
* If ribbon is to be used, we recommend that tension not be
applied. Refer to page 6 for more detailed instructions.
■Upper thread
Sewing machine embroidery thread (polyester thread)
or monofilament (transparent nylon) thread.
If you do not wish for the upper thread to be visible, we
recommend using transparent nylon monofilament
thread or polyester light weight thread (50wt. or above)
that is the same color as the lower thread.
■Needle
Use a needle appropriate for the upper thread and
fabric being used. For details, refer to your machine’s
Operation Manual.
■Presser foot
Utility stitches or decorative stitches: Monogramming
foot “N”
Free-motion sewing: Use the free-motion quilting foot
provided with your machine. If you do not have a free-
motion quilting foot, contact your nearest authorized
dealer to purchase one.
No.5 or finer hand embroidery
thread or decorative thread
Flexible woven ribbon
(approx. 2mm (approx. 5/64 inch)
recommended)
Fine embroidery ribbon (silk or
silk-like material) (3.5 mm (approx.
1/8 inch) or less, recommended)
Note
• Do not use thread heavier than No.5 hand
embroidery thread.
• Some threads may not be appropriate for bobbin
work. Be sure to sew trial stitches before sewing on
your project.
Note
• If monogramming foot “N” was not provided with
your machine, use zigzag foot “J”.
• When sewing a pattern described in the machine’s
Operation Manual and the monogramming foot “N”
is recommended, be sure to use this foot, otherwise
the desired results may not be achieved.
Free-motion quilting foot Free-motion open toe
quilting foot “O”

4
■Fabric
Be sure to sew trial stitches on a piece of scrap fabric,
which includes the same threads and fabric as what is
being used in your project.
Upper Threading
aInstall a needle appropriate for the upper
thread and fabric to be used.
For details on installing the needle, refer to the
machine’s Operation Manual.
bAttach the presser foot.
For the presser foot to be used, refer to “Required
Materials” on page 3.
For details on attaching the presser foot, refer to
the machine’s Operation Manual.
cThread the machine with the upper thread.
For details on threading the machine, refer to the
machine’s Operation Manual.
Preparing the Bobbin Thread
In order to create bobbin work, the bobbin case must
be replaced with the one for bobbin work.
Before creating bobbin work, clean the bobbin case
and the race.
aRaise the needle and presser foot, and then
turn off the machine.
bRemove the flat bed attachment.
cRemove the needle plate cover.
For details on removing the needle plate
cover, refer to the machine’s Operation
Manual.
aNeedle plate cover
dRemove the bobbin case.
aBobbin case
eUse the cleaning brush included with the
machine or a vacuum cleaner to remove any
lint and dust from the race and its
surrounding area.
aCleaning brush
bRace
fWipe the bobbin case (gray) with a soft lint
free cloth to clean it.
gInsert the bobbin case so that the projection
on the bobbin case aligns with the spring.
For details on inserting the bobbin case, refer
to the machine’s Operation Manual.
aProjection
bSpring
Note
• The sewing results may be affected by the type of
fabric used. Before sewing your project, be sure to
sew trial stitches on a piece of scrap fabric that is
the same as the fabric used in the project.
Note
• The bobbin case (gray) cannot be used for sewing in
any way other than bobbin work. After sewing
bobbin work, refer back to the steps in “Preparing
the Bobbin Thread” for removing and cleaning the
bobbin case (gray), and then reinstall the standard
bobbin case (black).

5
hWind a decorative thread around the bobbin
by hand. After winding the bobbin so it is
filled as shown below (about 80%), cut the
thread.
iUsing scissors carefully trim the thread tail as
close to the bobbin as possible.
aBeginning of wound thread
jInstall the bobbin wound with thread.
Whether or not tension should be applied to the
bobbin thread depends on the type of thread
being used.
■When tension is applied to the bobbin
thread
Insert bobbin into bobbin case so the thread unwinds
from the left side.
Then correctly pass the thread through the tension
spring as shown below.
aTension spring
CAUTION
• Be sure to use the bobbin case (gray) when creating
bobbin work. Using any other bobbin case may
result in the thread becoming tangled or damage to
the machine.
• Make sure that the bobbin case is correctly
installed. If the bobbin case is incorrectly installed,
the thread may become tangled or the machine may
be damaged.
CAUTION
• Be sure to use the machine’s included bobbin or one
designed specifically for this machine. Using any
other bobbin may result in damage or injuries.
Actual size
This model Other models
Note
• Slowly and evenly wind the thread around the
bobbin.
• For best results, wind the bobbin so the thread is
snug and not twisted.
CAUTION
• If thread extends beyond the top of the bobbin too
much, the thread may become tangled or the
needle may break.
11.5 mm
(approx.
7/16 inch)
CAUTION
• When winding the bobbin, make sure the thread is
not frayed. Sewing with frayed thread may result in
the thread catching on the tension spring of the
bobbin case, the thread becoming tangled or
damage to the machine.
• Do not guide the bobbin thread through the groove
in the needle plate cover, otherwise the lower
threading cannot be done correctly.

6
■When tension is not applied to the bobbin
thread
If the bobbin thread in the trial stitching is too tight and
adjusting the bobbin case tension does not help (*As
described in “Adjusting the Tension of the Bobbin
Thread” on page 13), do not pass the thread through the
tension spring.
Hold the bobbin with your left hand so the thread
unwinds from the right side and hold the end of the
thread with your right hand.
kPull out about 8 cm (approx. 3 inches) of
bobbin thread.
lLightly hold the end of the upper thread while
turning the handwheel toward you
(counterclockwise) until the mark on the
handwheel aligns with the center top of
machine.
mGently pull the upper thread to bring the
bobbin thread up through the needle plate.
→A loop of the bobbin thread comes out through the
hole in the needle plate.
nInsert tweezers through bobbin thread loop
and pull bobbin thread above the needle
plate.
oAlign the upper thread and bobbin thread,
and then pull out about 10 cm (approx.
4 inches) of the threads and pass them under
the presser foot toward the rear of the
machine.

7
pInstall the needle plate cover and bobbin
cover with tabs.
For details on installing the needle plate cover,
refer to the machine’s Operation Manual.
aNeedle plate cover
bBobbin cover with tabs
qInstall the flat bed attachment.
→This completes the upper and lower threading.
Note
• Two bobbin covers may be included, depending on
the country or region where this kit was purchased.
Use the bobbin cover with the same shape as the
bobbin cover included with your machine. The
bobbin cover with a shape different than that
included with your machine cannot be installed on
the machine.
CAUTION
• When creating bobbin work, use the bobbin cover
with tabs, otherwise the thread may become
tangled or the needle may break.
Note
• When installing the needle plate cover, do not allow
it to pinch the thread.
Note
• When installing the flat bed attachment, do not allow
it to pinch the thread.
• When the bobbin thread is replaced with a new one,
be sure to repeat the procedure from aon
“Preparing the Bobbin Thread”, otherwise the lower
threading will not be done correctly.

8
CREATING BOBBIN WORK
Positioning the Fabric and Sewing
aPlace a lightweight tear-away stabilizer on
top (wrong side) of the fabric.
bUsing an awl, punch a hole in the fabric at the
beginning of stitching so the bobbin thread
can be fed through the fabric.
cUse the presser foot lever to raise the presser
foot.
dWith the wrong side facing up, place the
fabric with stabilizer under the presser foot.
aWrong side of fabric
bStabilizer on wrong side of fabric
eTurn the handwheel toward you
(counterclockwise) to feed the needle into the
punched hole. Position the upper thread over
the presser foot and lightly hold then, lower
the presser foot.
aPunched hole
bUpper thread over the presser foot
fPulling the upper thread gently, turn the
handwheel toward you (counterclockwise)
until the mark on the handwheel aligns with
the center top of machine.
→A loop of the bobbin thread comes up through the
hole in the fabric.
gRaise the presser foot lever, and then use
tweezers to pull up the bobbin thread and
bring the end of the thread to the top of the
fabric.
Note
• Be sure to sew trial stitches using same fabric and
threads as your project in order to check the sewing
results.
• The bobbin thread may become tangled due to the
type of pattern and thread that are being used. Since
this may cause the needle to break, immediately
stop sewing if this occurs. Turn off the machine and
cut out the tangled thread with scissors. Then, clean
the race and bobbin case as described in “Preparing
the Bobbin Thread” on page 4.
Note
• Pull the thread while holding down the fabric so it
does not move out of place.

9
hAlign the upper thread and bobbin thread,
and then pass them under the presser foot
toward the rear of the machine.
iTurn on the machine.
jSelect a stitch.
kAdjust the upper thread tension.
For details on adjusting the upper thread tension,
refer to the machine’s Operation Manual.
lIf your machine is equipped with the
automatic thread cutting function and
automatic reinforcement/reverse stitching
function, make sure the automatic thread
cutting and automatic reinforcement/reverse
stitching have been turned off.
mWhile gently holding threads at the rear of the
machine, turn the handwheel to feed the
needle into the punched hole again, and then
lower the presser foot lever.
nSelect a low speed, gently hold the threads
behind the presser foot and start sewing.
Threads can be released after several stitches
have been made.
oWhen you have reached the end of the
stitching area, stop the machine.
pRaise the needle and presser foot.
Memo
• For best results, select a longer stitch length and a
wider stitch width. Depending on the selected stitch,
it may not be possible to change the stitch length
and stitch width settings. For details on adjusting the
stitch length and stitch width, refer to the machine’s
Operation Manual.
• Depending on the fabric, bunched stitches may
result. We recommend selecting a simple stitch and
sewing trial stitches to check the sewing results.
Examples of simple stitches: , ,
Memo
We recommend an upper thread tension that is higher
than the standard setting.
CAUTION
• Before sewing, make sure the automatic thread
cutting has been turned off. If sewing is started with
automatic thread cutting turned on, the thread may
become tangled or the machine may be damaged.
Note
• Before sewing, check that there is enough thread in
the bobbin.
Note
• Do not sew reinforcement/reverse stitches at the
end of the stitching, otherwise the threads may
become tangled or the needle may break. In
addition, it will be difficult to pull the bobbin thread
up to the wrong side of the fabric.

10
qLeaving about 10 cm (approx. 4 inches) of
thread at the ends, use scissors to cut the
threads.
a10 cm (approx. 4 inches)
Finishing the thread ends
aAt the end of the stitching, pull the end of the
bobbin thread up to the wrong side of the
fabric.
aWrong side of fabric
bBobbin thread
bFrom the wrong side of the fabric, tie the
bobbin thread and the upper thread together
by hand, and then cut off excess threads with
scissors.
aWrong side of fabric
bSurface of fabric
cIf the desired results could not be achieved,
adjust the tension of the bobbin thread and of
the upper thread, and then try sewing the
stitching again.
For more details, refer to “ADJUSTING THE
THREAD TENSION” on page 13.
Note
• Do not sew reinforcement/reverse stitches or use a
“Thread Cutter” button (if so equipped) at the end of
the stitching; otherwise it will be difficult to pull the
bobbin thread up to the wrong side of the fabric. In
addition the threads may become tangled or the
needle may break possibly causing machine
damage.
Note
• If it is difficult to pull up the bobbin thread, use a
ribbon embroidery needle to pull the thread up to the
wrong side of the fabric. Otherwise, use an awl to
pull up the bobbin thread.
Note
• To ensure threads do not come undone after being
tied place a drop of fabric glue on knots.

11
Bobbin Work Free-Motion Sewing
If so desired, use a template or draw your design on the
stabilizer to allow for ease of stitching. Remember, your
stitches with your decorative thread will be on the
underneath side of your fabric and the stabilizer will be
on the top of the wrong side of your fabric.
The CD-ROM included with this kit contains template
data for free-motion sewing. For a list of the template
designs, refer to “Templates for Free-Motion Sewing”
on page 12.
aPrint the desired template.
bAffix the stabilizer to the wrong side of the
fabric.
cPlace commercially available transfer paper
on the stabilizer, then the paper printed with
the template on top, and then trace the design
with a pencil.
aTemplate
bTransfer paper
cStabilizer on wrong side of fabric
dOnce the design is transferred to the stabilizer,
position the fabric under the free-motion
presser foot on the machine, and then use free-
motion sewing to sew the design.
Note
• For bobbin work free motion sewing use the
instructions for “CREATING BOBBIN WORK”
beginning on page 8.
• Use the quilting foot provided with your machine. If
you do not have a quilting foot, contact your nearest
authorized dealer to purchase. For details on using
the quilting foot, refer to the Operation Manual
provided with your machine or with the presser foot.
Note
• Print the template in its original dimensions. If an
enlarged template is used, the bobbin thread may
run out during sewing.
Note
• Some templates have the arrows to show you the
sewing direction. Trace the arrows with design.

12
Templates for Free-Motion Sewing
aWrong side of fabric (template design)
bRight side of fabric
Note
• Bobbin work is sewn with the wrong side of the fabric facing up. For this reason, the template designs are backwards.
No.1
No.01.pdf
No.2
No.02.pdf
No.3
No.03.pdf
No.4
No.04.pdf
abababab
No.5
No.05.pdf
No.6
No.06.pdf
No.7
No.07.pdf
No.8
No.08.pdf
abababab
No.9
No.09.pdf
No.10
No.10.pdf
No.11
No.11.pdf
No.12
No.12.pdf
abababab
No.13
No.13.pdf
No.14
No.14.pdf
No.15
No.15.pdf
No.16
No.16.pdf
abababab
No.17
No.17.pdf
No.18*
No.18.pdf
No.19*
No.19.pdf
No.20
No.20.pdf
abababab
* These templates have the arrows to show you the sewing direction. Trace the arrows with design when transferring the design to the
stabilizer.

13
ADJUSTING THE THREAD TENSION
After sewing trial stitches and checking the sewing results, adjust the thread tensions if necessary. After adjusting the
tensions, be sure to sew trial stitches again in order to check the sewing results.
Adjusting the Upper Thread Tension
We recommend an upper thread tension that is higher
than the standard setting.
Refer to the machine’s Operation Manual for detailed
instruction.
Adjusting the Tension of the Bobbin
Thread
If the desired stitching cannot be achieved after
adjusting the upper thread tension, adjust the tension of
the bobbin thread. The tension of the bobbin thread can
be adjusted by turning the slotted-head (–) screw on the
bobbin case (gray) for bobbin work.
aDo not turn the phillips screw (+).
bAdjust with the small screwdriver.
To increase the tension of the bobbin thread, turn the
slotted-head (–) screw 30° to 45° clockwise.
To decrease the tension of the bobbin thread, turn the
slotted-head (–) screw 30° to 45° counterclockwise.
Note
• Turning the screw on the bobbin case (gray) may
push up the spring plate, as shown below.
If this occurs, gently press down the spring plate
with a screwdriver so it is lower than the top surface
of the bobbin case (gray), and then insert the bobbin
case into the machine.
aSpring plate
CAUTION
• DO NOT adjust the position of the phillips (+)
screw on the bobbin case (gray) as this may result in
damage to the bobbin case, rendering it useless.
• If the slotted screw (-) is difficult to turn, do not use
force. Turning the screw too much or providing
force in either (rotational) direction may cause
damage to the bobbin case. Should damage occur,
the bobbin case may not maintain proper tension.
Note
• If the bobbin thread tension is tight, the thread
cannot be passed through the tension spring when
the bobbin is installed in the bobbin case. (Refer to
“When tension is not applied to the bobbin thread”
on page 6.)

14
TROUBLESHOOTING
Several solutions for minor problems are described below. If the problem persists, contact your nearest authorized
dealer.
■The thread was accidentally cut
automatically and the bobbin thread is
caught inside the machine (Only for
machines equipped with the automatic
thread cutting function)
aCut the thread near the fabric above the
needle plate, and then remove the fabric.
aThread
bRemove the bobbin, and then hold it out
toward the left side of the machine.
cLower the presser foot.
dPress the “Thread Cutter” button again, and
then pull the thread out to the left while the
thread cutter is operating.
■The pattern is misaligned
Refer to “ADJUSTING THE THREAD TENSION” and
increase the upper thread tension. If the pattern is still
misaligned, reduce the tension of the bobbin thread.
Example: Decorative Stitch
aCorrect tension
bThe upper thread tension is too loose, or the bobbin
thread tension is too tight.
■The bobbin thread catches on the tension
spring of the bobbin case
Sew with no tension applied to the bobbin thread.
(Refer to “When tension is not applied to the bobbin
thread” on page 6.)
CAUTION
• Do not pull on the thread with excessive force,
otherwise the machine may be damaged.

English
111-001