BSD BL-100 User manual

nQ''
=E--E=E
:::
NETWORl(S
Fiber & Data Cofrmunicotiont
'*"Brief
introduction
Many
thanks
forpurchasing
Fast
Ethernet
optical
transceiver!
This
product
supports
IEEE802.3u
I00Base-Tx/Fx
proiocol,
as
wellas
full duplex
and
halfduplex
mode.
This
manual
is
for l00M
transceivers.
The
following
purchasing
guide
is
forcustomer,
s
reference.
Purchasing
guide
for opticaltransceivers
llodel Speclflcaflons
UTP-MM l0l.tOOM
adaptive,
multi
mode
2km,
ST
UTP-SM 10/,lO0M.adaptive,
single
mode
25km,
SC
UTP-SM 10/1OOM
adaptive,
single
mode4okm,
SC
UTP-SM 10/109M
adaptive,
singte
mode
60km,
SC
UTP-SM 10/100M
adaptive,
single
mode
100km,
SC
Packing
list
PIease
check the following items in thepackagebefore installing
lhe transceiver.
o Fast Ethernet optical transceiver
. ACIDC adapter (external)
o Power line (built-in)
. User manual
Iset
lpc
lpc
lcopy Figure I Schematicdrawing ofconnection
Please contact the dealer immediately for any loss or damage
to the above items.
2
Fast
Ethernet
Optical
Transceiver
BL-100
User
Manual
h
tt
p://www.
bs
dnetwo
r
ks.
com
(Donotuseuntil you
read
this
manual
carefully)
', Installation
l. Interface
RJ-45interface
The transmission
mediaadopts CAT5 twisted-pair with
typical length of 100 meter. It features the function of
automatically
identifying
thethrough
line
and
crosswire
Fiberinterface
SC/STfiberinterface
isof duplexmodetype,includingtwo
interfaces,
namelyTX and RX. Whenthe two setsof optical
transceiver
are interfaced or connected
to switchwith fiber
interface,
thefiberisincrosdconnection,
namely..TX-RXi,..RX-
TX" (direct
butting
forsingleoptical
fiber).
2.Connection
The networkdevice(workstation, hub
orswitch)with RJ-45
interface
isconnected
toRJ-45
jackof opticaltransceiver
through
twisted-pair.
Andthemulti/singlemode
fiberis con:rected
to
SC/STfiber interface
oftheoptical transceiver.Then
switchon.
The corresponding
LEDisonfor correctconnection. (Seettre
tablebelowfor the LED indicator
lamp)
TX R(
PWR 'OOM
oo
oolr'l I
soo OSgf
-

r* Expfanation
forLEDindicatorlamp
LEDindicator lampsserve as devicemonitoring andtrouble
display.The following is theexplanation for eachLED indicator
lamp.
LED
indicatorlamp Status Explanation
FX
Link/Act
On Connoction status display for fiber link.
"ON" indicatesthatFiberlinkisin
corrsct conngction.
Blink Active status display of fib6r link "Blink"
Indicates
packetgoes
throughFxond.
TX
Link/Act
On Connectionstatusdlsplayforslectriclink.
"ON" indicatesthatelectric
link
isin
co116ct
conn6ction.
Blink Active status display of fibor link 'BlinK'
indicates packet go€s through Tx end.
FDX/COL On Transceiverworks
in
the
full
duplox
mode.
off Transceiverworkslnthohalfduolexmods.
PWR On Powerison and normal.
SD On Fiber signal isdetect€d,
1
00M On Transfer rats of eloctrlc Intsrface ls 100MbDs
off Rate of €lectric int6rface is 10Mbos
Transmissioncharacteristicsof singlefiber transceiver
Product
model optical
wavelength
(m) Transmitting
optical
powor Recslvlng
6onsitivity distance
(km)
UTP-SM
(25km) t
3't
0/1550
1550/1310 -12-6 '12 25
UTP.SM
(40km) 1310/1550
1550/1330 -3-5 <-31 40
UTP-SM
(60km) 1310/1550
't
550/1330 -5-9 <-44 00
"Su
1
!
r+ Fiber
transmissionfeatures:
r+ Mainfeatures
l. In conformity toIEEE802.3I0Base-T
standard.
In conformity to IEEE 802.3u100Base-TX/FXstandard.
2.Max.2M buffermemorybuilt inchip.
3.Backpressure flow control for fulI duplex.
IEEE802.3X and halfduplex.
4.Automaticidentification of MDI/MDI-X crossline.
5.High-performancel.4Gbpsmemory
bandwidth.
6.In conformity to safety
codeof FCCandI5CLASS A and
CEMARK.
r+ Technical
parameters:
l. StandardProtocol:IEEB802,3I
0Base-Tstandard
IEEE802.3uIO0Base-TX/FXstandard
2.Connector:one
UTP RJ-45connector,one SC/STconnector
3.Operationmode:full duplexmode
orhalf duplexmode
o**
\
I
Product
model
Optical
wavel6ngth
(nm)
optical
power
(dbm) Sensibility
(dbm) Saturability
(dbm)
UTP-MM 1310 -19- -14 -31 -12
UTP.SM
25 1310 -'t4
- -7 -34 -3
UTP.SM
40 1310 -9--5 -38 -3
UTP-SM60 '| 310 -5--0 -3E -3
UTP-SM
1OO 155ODFB -5--0 -38 -3
4.
Powersupply
parameter:
Outside:
5VDC 1A
Built-in: Il0-265VAC 48VDC
5.Environmental
temperature:
0C-60C
6.Relative
humidity; 5%-90%
7.TPcable:
Cat5UTPcable
8.Transfer
fiber:
Multi-mode:
50/
125,62.5/
125or I00/140
um
Single
mode:8.3I125,8.7I125,9I
125or l0/
125
vm
9.Dinensions:
External
powersupply:26mmx7lmm x94mm
Built-inpower
supply:
40mm
x 1lOmm
x 140mm
rr Cautions:
l. Thisproduct
issuitable
for indoorapplication.
2.Putonthedustcover
offiber interface
when
notused.
3.It isforbiddento stareattheTX fiber-transfer
endwith
nakedeyes.
4.Single
optical
fiber
transceiver
mustbe
usedinpair
(Seethe
attachment
description
in delivery).
r*Trouble
shooting:
l' Deviceis notmatched.
Pleaseselect
thecorresponding
network
device
according
tothe
transfer
rateofthe
product(l0Mbpsor l00Mbps)
whenconnectedto
other
network
devices
(networkcard,
hub,switch).
2.Line lossisexcessive
duringthefiber wiring' Excessivelossin
connector
plug-in andfiber soldering
welding,andexcessive
intermediate
nodes
maycause
excessive
lossrateor-abnormal
operation.
Figur€2Dip
Switch
+Toggle
ONpin 1to LFPis enable; OFFis disable.
*Toggle
OFF
pin2 and
toggle
OFF
pin 3
to Storeandforward
switchisenable
OFF
pin2 andon pin 3toModified cut-through
switchmodeisenable.
On
pin 2andoffpin 3to convertermodeis enable.
On
pin 2andon pin 3toconverterwith auto-change-forward
functionisenable.
* Toggle
OFF
pin 8to forcefiber portwork full duplex.
On
pin 8toforcefiber portwork halfduplex.
* Toggle
OFF
pin 5
to support IEEE802.3Xisenable.
On
pin 5tosupportIEEE802.3Xisdisable.
* ToggleOFF
pin4,toggleoffpin 6andtoggleoffpin 7toforceTX port
work l0M/100M,Full Duplex/Half Duplexwith autonegotiation.
OFF
pin4,offpin 6andon
pin 7to forceTX port work I0M
/100M,Half Duplexwith autonegotiation.
OFF
pin 4,on pin 6and
offpin 7
to forceTX port work 10M,Full
Duplex/Half Duplexwith autonegotiation.
OFF
pin4 on pin 6andon pin 7to forceTX port work 10M,Half
Duplexwith autonegotiation.
On
pin 4OFF pin 6andOFF pin 7to forceTX port work 100M,Ful1
Duplexwith autonegotiation,
On
pin 4off pin 6andon pin 7toforceTX portwork 100M,Half
Duplexwith autonegotiation.
On
pin 4,on
pin 6and
off pin 7to forceTX port work l0M,Full Duplex
with autonegotiation.
On
pin 4on pin 6and
on
pin 7to forceTX port work l0M,Half Duplex
with autonegotiation.
,i Dipswitch
DipSwitch:Top
position
isON,
Low
position
is
OFF
5r il$,