BSLight BS-ZGX5 User manual

C/ Arabia 24, Pol.Ind. Congost 08520 Les Franqueses del Valles -Bar elona -España Tel: [phone]
e-mail: light@bsvele troni . om www.bslight.es www.bsvele troni .om
BS-ZGX5
Controladores
controllers
Caracteristicas tecnicas / Technical data
Alimentación/ power supply 110V-230V
Tipo de control/ dimmmable surpport 4 Zonas/
Zones
Medidas Mando/ remote control dimensions
86x86x29.1mm
Alimentacio Zonas Medidas
Referencia
Reference Power supply Zones Measure
BS-ZGX5 4 86x86x29.1mm
Carga Máx.
Max.Charge
30 Receptores
Medidas Receptor/ Receiver dimensions
Frec.de trabajo del mando/ Work frequency command
2.4Ghz
Dist. de señal del mando/ Command signal distenace 30mts
1145x46.5x16mm
110V-230V
BS-ZG1029 −− 12−24Vdc 1145x46.5x16mm 4A x Canales/
Channels
Tipo de Control
Type of control
60.3 mm
ZigBee Controller
AC Power input
L
52.0 mm
60.3 mm 52.0 mm
19.4 mm
N

C/ Arabia 24, Pol.Ind. Congost 08520 Les Franqueses del Valles -Bar elona -España Tel: [phone]
e-mail: light@bsvele troni . om www.bslight.es www.bsvele troni .om
BS-ZGX5
Controladores
controllers
LED indicator
Important: Read All Instructions Prior to Installation Function introduction
Brightness wheel, slide
clockwise to increase
light intensity, slide
counter-clockwise to
decrease light intensity
All ON/OFF button, click to switch ON/OFF all
paired lighting devices
Press and hold down to search and pair to
ZigBee network or factory reset the dimmer
switch.
Note: This remote supports 4 groups for
binding max. 30 lighting devices. 4 scenes
can be saved and recalled for each group.
Group buttons, click to choose a
group, press and hold down to turn
ON/OFF it
Scene buttons, press and hold down
to save a scene, click to recall it.

C/ Arabia 24, Pol.Ind. Congost 08520 Les Franqueses del Valles -Bar elona -España Tel: [phone]
e-mail: light@bsvele troni . om www.bslight.es www.bsvele troni .om
BS-ZGX5
Controladores
controllers
•DO NOT install with power applied to the device.
•DO NOT expose the device to moisture.
Safety & Warnings
Operation
Product Data
Protocol
Input Voltage
Transmission Frequency
Transmission Range (free field)
Protection Type
Dimming Range
Dimensions
ZigBee 3.0
100-240VAC
2.4GHz
30m
IP20
0.1%-100%
86x86x29.1mm
• ZigBee wireless dimmer switch based on ZigBee 3.0
• Full touch glass interface, smooth light intensity control
• Enables to pair ZigBee lighting devices via touchlink
commissioning without coordinator
• Supports find and bind mode to pair with ZigBee lighting
devices
• Supports 4 groups for binding max. 30 lighting devices
• 2.4 GHz global operation
• Transmission range up to 30m
• Compatible with universal ZigBee Gateway products
• Compatible with universal ZigBee dimmable lighting devices
ZigBee Clusters Supported by This Remote Are As
Follows: Input clusters:
Power Configuration
•Basic • Output
clusters: •Identify •Scenes •Group
•Identify
•On/off
•Diagnostics
•Level control •Ota
1.This ZigBee dim remote is a wireless transmitter that communicates with a variety of ZigBee compatible
systems. This transmitter sends wireless radio signals that are used to remotely control a compatible system.
2.This ZigBee remote supports 4 groups for binding max. 30 lighting devices and enables to control single color
ZigBee lighting devices.
3. igbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network)
Step 1: Remove the remote from
previous zigbee network if it has
already been added to it, otherwise
pairing will fail. Please refer to the
part "Factory Reset Manually".
Step 3: Press and hold down until
LED indicator turns on.
Step 2: From your zigbee controller or hub
interface, choose to add device or accessory and
enter Pairing mode as instructed by the controller.
Step 4: Immediately short press to search nearby
network, indicator flashes every 1 second, 20
seconds timeout if there is no network. Indicator
will then blink 5 times quickly for successful
pairing.
LED indicator

C/ Arabia 24, Pol.Ind. Congost 08520 Les Franqueses del Valles -Bar elona -España Tel: [phone]
e-mail: light@bsvele troni . om www.bslight.es www.bsvele troni .om
BS-ZGX5
Controladores
controllers
4. ouchLink to a Zigbee Lighting Device
Note: 1) Directly TouchLink (both not added to a ZigBee network), each remote can link with 30 devices.
2) TouchLink after both added to a ZigBee network, each remote can
link with max. 30 devices.
3) For Hue Bridge & Amazon Echo Plus, add remote and device to
network first then TouchLink.
4) After TouchLink, the remote can control the linked lighting devices.
LED indicator
5. emoved from a Zigbee Network through Coordinator or Hub Interface
6. actory Reset Manually
Note: 1) After pairing successfully, the remote information will appear on the controller or hub interface.
2) No remote information will appear on the hub interface if pairing to Philips Hue Bridge.
Step 1: Set the zigbee lighting
device to start TouchLink
commissioning, please refer to its
manual to learn how. ZigBee Lighting Device
< 10cm
Step 2: Bring the remote within
10cm of the lighting device.
Step 3: Short press any button to
choose a group to touchlink
Step 4: Press and hold down until
LED indicator turns on.
Step 5: Immediately short press to start TouchLink
commissioning of the remote. LED indicator flashes
fast for 3S, then flash 6 times slowly to indicate
successful pairing to the device and the light
connected to the device will blink twice.
LED indicator
Step 1: Press and hold
down until LED indicator
turns on.
From your ZigBee controller or hub interface, choose to
delete or reset the remote as instructed, indicator flashes 3
times quickly to indicate successful removing.
Note: All configuration parameters will be reset after
the remote is reset or removed from the network.
Step 2: Immediately short press 5 times continuously,
indicator flashes 3 times quickly to indicate successful
reset.

C/ Arabia 24, Pol.Ind. Congost 08520 Les Franqueses del Valles -Bar elona -España Tel: [phone]
e-mail: light@bsvele troni . om www.bslight.es www.bsvele troni .om
BS-ZGX5
Controladores
controllers
7. emove a Touchlink Paired ZigBee Lighting Device
8. actory Reset a Lighting Device (Touch Reset)
Note: the device shall be added to a network, the remote added to the same one or not added to
any network.
9. ind and Bind a Zigbee Lighting Device
Note: Make sure the device and remote already added to the same zigbee
network.
Note: Each remote can bind max. 30 lighting devices.
LED indicator
Step 1: Set the Touchlink
pairedzigbee device to start
TouchLink commissioning, please
refer to its manual to learn how. ZigBee Lighting Device
< 10cm
Step 2: Bring the remote within 10cm of
the lighting device.
Step 3: Short press the group
button that the device was linked to.
Step 4: Press and hold down
until LED indicator turns on. Step 5: Immediately short press twice to
start TouchLink removing of the remote. LED
indicator flashes fast for 3S, then flash 6
times slowly to indicate successful removing.
LED indicator
Step 1: Set the zigbee device
to start TouchLink
commissioning,refer to its manual.
ZigBee Lighting Device
< 10cm
Step 2: Bring the remote within 10cm of the
lighting device.
Step 3: Press and hold down
until LED indicator turns on.
Step 4: Immediately short press 5 times to
start Touch Reset of the remote. LED
indicator flashes fast for 3S, then flash 3
times slowly to indicate successful reset.
LED indicator
Step 1: Start find and bind mode
on the Zigbee lighting device
(initiator node) and enable it to find
and bind target, refer to its manual. ZigBee Lighting Device
Step 2: Short press a group button
that you would like to bind the
device to.
Step 3: Press and hold down until
LED indicator turns on.
Step 4: Short press to enable the remote
(target node) to find and bind initiator.LED
indicator flashes 4 times for successful
binding or twice if binding fails.

C/ Arabia 24, Pol.Ind. Congost 08520 Les Franqueses del Valles -Bar elona -España Tel: [phone]
e-mail: light@bsvele troni . om www.bslight.es www.bsvele troni .om
BS-ZGX5
Controladores
controllers
10. ind and Unbind a Zigbee Lighting Device
11. lear All Find and Bind Mode Paired Lighting Devices
12. etup a Network & Add Devices to the Network (No Coordinator or Hub Required)
LED indicator
Step 1: Start find and bind mode on
the Zigbee lighting device (initiator
node) and enable it to find and bind
target, refer to its manual.
ZigBee Lighting Device
Step 2: Short press the group button
that the device already bound to.
Step 3: Press and hold down until
LED indicator turns on.
Step 4: Short press twice to enable the
remote (target node) to find and unbind
initiator. LED indicator flashes 4 times for
successful unbinding or twice if unbinding
fails.
LED indicator
Step 1: Short press to choose the
group that you would like to unbind all
devices.
Step 2: Press and hold down until
LED indicator turns on.
Step 3: Short press 5 times
continuously to clear all bound lighting
devices . LED indicator flashes 4 times
for successful unbinding.
LED indicator
Step 1: Factory reset the remote and
the lighting device, refer to their
manuals. ZigBee Lighting Device
< 10cm
Step 2: TouchLink the remote and device to
setup a network, refer to
their manuals.
Step 3: Short press the group button
that the device was linked to.
Step 4: Set another remote into
network pairing mode and pair it to
the network, refer to its manual.
Step 5: Add more remotes to the network as you would like.
Step 6: Factory reset the lighting devices that you would like to add to the network, refer to
their manuals.
Step 7: Touchlink to pair the added remotes and lighting devices you would like to add, the
devices will be added to the network through Touchlink, refer to their manuals.
13.OTA
The remote supports firmware updating through OTA, and will acquire new firmware from
zigbee controller or hub every 10 minutes automatically.

C/ Arabia 24, Pol.Ind. Congost 08520 Les Franqueses del Valles -Bar elona -España Tel: [phone]
e-mail: light@bsvele troni . om www.bslight.es www.bsvele troni .om
BS-ZGX5
Controladores
controllers
14. How to Check Whether the Remote Belongs to a Network or not
Short press any other buttons except group buttons, indicator blinking means the remote has already been
added to a network, no blinking of indicator means the remote does not belong to any network.
Wiring diagram
AC 100-240V
AC Power
50/60Hz
ZigBee Controller
L N
Installation