Bubbli BBCHAIRHISA User manual

Speckles High Chair
BBCHAIRHISA
Quick Start Guide
Safety Precautions
Please read all instructions carefully and keep a copy of these instructions for
future reference.
•Follow all instructions
•Do not leave children in the chair unattended
•The harness must always be used and correctly fitted – most injuries
from high chairs are caused by falls
•Position the high chair away from solid structures and benches to avoid
injuries caused by falls and by access to dangerous items
•Check that all safety locks are engaged before placing child in the high
chair.
•Always keep child in view while they are in the high chair.
•Not recommended for children under 6 months old.
•The tray is not designed to hold your child in the high chair.
•Use safety locks and brakes at all times.
•Always secure your child in the restraint. nsure that you child wears a
correctly fitted and adjusted harness at all times.
•The high chair should only be used in an upright position once the child is
capable of reliably and consistently sitting upright.
•Only use the high chair on a secure, level surface.
•Do not allow children to stand on the seat or footrest, or climb into or out
of the high chair.
•When adjusting the high chair, make sure that parts of your child's body
are clear of any moving parts.
•Do not carry the high chair with your child in it.
•To reduce the risk of injury, position the high chair away from furniture,
walls, hot surfaces and liquids, window curtain cords and electrical cords.
Position the high chair away from furniture when the high chair is not
being used at a table with the tray removed.
•Periodically check that all parts of the high chair are in good working
order.
•Do not use the high chair if it is damaged for broken. Contact the Kogan
customer support team for repair advice.
•Do not use the high chair unless all components are correctly fitted and
adjusted.
•The weight of the child using this high chair should not exceed 17kgs.
•Promptly replace worn out or broken parts.

Assembly Contents
Seat x 1 Tray x 1 Foot Rest x 1 Leg Assembly x 2 Leg Base Moulds x 2
(Castors fitted)
Plastic Clips x 2
(1 pre-assembled)
Plastic Caps x 2
(1 pre-assembled)
Support Tube Fixing
Screws, Nuts and
Washers x 2
Fixing Bar (axle) x 1 Support Tube x 1
Assembly/Operation Instructions
To assemble the high chair
Open the main frame leg assemblies and join them
together by placing the seat support tube between
them. Secure with screws, nuts and washers
provided.
To fit leg base mouldings
Attach the leg base mouldings onto the bottom of
the front and rear legs. nsure that the leg base
moulds with “F” stickers match the “F” on the front
legs. Secure the mouldings to the legs by pushing
them into position. nsure the pop-up pins are
engaged.
To attach the seat
Place the seat onto the support tube by inserting
the pedestals into the recess at the top of the leg
assemblies as shown in the image. nsure the seat
clicks into place.
1. Push the axle bar through the leg
assemblies and the seat.
2. Press the plastic clip into the groove at the
end of the axle.
3. To secure, press the plastic cap over the
plastic clip. 1 2 3

To attach the foot rest
Place the footrest along the front of the seat
assembly. Press firmly to ensure it 'clicks' into
position.
To adjust the seat height
Squeeze the levers on both front legs of the chair
and raise or lower to the desired position.
To attach and use tray
1. Attach tray by aligning it with the armrests,
and squeezing the lever under the front of
the tray, slide tray along armrests.
2. To adjust tray, squeeze the lever under the
front of the tray and slide to 1 of 3 positions.
To lift the armrest
Press the button on the side of the armrest, then lift.
Harness restraints
To secure your child in the hardness, push buckle (a) and (b) into the
buckle housing (c), until the buckle prongs snap into position.
Carefully adjust the harness by pulling the slider (d) until the desired
fit is achieved in the lap, shoulder and crotch strap. To release the
buckle, squeeze the top and bottom prongs until it disengages.
•CAUTION: The harness must be used at all times and be
correctly adjusted
To fold the high chair
1. Remove tray.
2. Squeeze levers on both rear legs of the
chair and slide upwards while pushing the
rear legs towards the front legs.
3. The tray can be stored by placing it on the
buttons that are located on the rear legs.
Cleaning
To ensure the long-lasting use of your high chair, wipe down with a damp cloth
and use a mild soap solution if necessary. Do not use abrasive cleaners. Always
store product in a clean, dry place.
Maintenance
Always check parts regularly for the tightness of screws, nuts and other
fasteners – tighten or replace if required.