BUDDEE BD903205-BK User manual

Thank you for purchasing a Buddee Digital Clock Radio.
For optimum performance and safety, read these instructions
carefully before connecting, operating or adjusting this product.
Refer to this manual for future reference.
INTRODUCTION
Never be late again with the Buddee Dual Alarm Digital
Clock Radio. Set alarms for multiple times of the day or night
to ensure you wake up on time ready for your important
appointments.
Dual alarms and AM/FM radio allow you to wake up how
and when you like while the compact size fits easily on your
bedside table.
DEVICE FUNCTIONS
1. Set alarm 1 / Increase volume
2. Set alarm 2 / Decrease volume
3. Radio ON/OFF / Select AM/FM
4. Set time / Set radio presets
5. Previous radio preset
6. Next radio preset
7. Set minutes / Increase radio frequency
8. Set hour/ Decrease radio frequency
9. Set sleep timer / Snooze alarm
10. PM indicator
11. Alarm 1 Buzzer indicator
12. Alarm 1 Radio indicator
13. FM indicator
14. Alarm 1 Buzzer indicator
15. Alarm 2 Radio indicator
POWER SOURCE
Please check carefully that the voltage indicated on the rating
label corresponds to the voltage of your area. Plug the AC cord
into a standard wall socket.
BATTERY BACKUP
This unit has a backup battery which provides power in the
event of a power outage.
1. Remove battery door.
2. Insert 2 new AAA batteries (not included).
3. Replace the battery door.
If there is a power failure, the time setting, alarm setting and
memory settings will not be affected. The LED display will not
be illuminated while backup battery is in use. After AC power is
restored, the unit will function normally with the settings from
before the power outage.
Note: If the unit will not be used for an extended period of time,
disconnect from AC power and remove the batteries.
SNOOZE
SLEEP
AM/FM PRESET
ON/OFF TIME P- P+
AL1
AL2
HOUR
MINUTE
V
O
L
U
M
E
T
U
N
I
N
G
1
10
11
12
13
14
15
9
3 4
2
8
7
5 6
DUAL ALARM DIGITAL CLOCK RADIO
0.6” LED DISPLAY
USER MANUAL
© Buddee Gear 2016. All rights reserved. All trademarks are
registered trademarks of respective manufacturers listed.
Made in China
FEATURES
• Dual alarms
• AM/FM radio
• Sleep and snooze functions
• 20 radio presets
• Radio or buzzer alarms
PACKAGE CONTENTS
Before attempting to use this unit, please check the packaging
and make sure the following items are contained in the shipping
carton:
• Main unit (Dual alarm digital clock radio)
• Power cable
• User manual
TECHNICAL SPECIFICATIONS
Power source: AC 220V-240V 50Hz
Power consumption: 5W
Radio frequency: FM 87.5-108MHz
AM 522-1620kHz
Speaker: 50mm 8 (ohm), 0.5W
Battery backup: 1.5V (AAA battery) x2 (not included)

OPERATING THE RADIO
1. Press the ON/OFF button once to turn the radio on.
The radio will begin playing on the FM band.
2. Press the AM/FM button to switch between AM and FM.
3. Adjust the volume with the VOLUME buttons.
Volume range: 00 (mute) to 16 (max).
4. Use the TUNING buttons to tune to your desired station.
Manual Tuning: Press either of the TUNING buttons repeatedly
to reach the desired frequency. In AM mode, each press will
adjust the frequency up or down by 9KHz. In FM mode, each
press will adjust up or down by 0.1MHz.
Automatic Scanning: Press and hold either of the TUNING
buttons to auto scan. Scanning will stop automatically when
a clear signal is found. Repeat until the desired station is
reached. *To stop auto scanning, press any button once.
Note: In areas where the radio signal is not strong, auto
scanning may fail to find a strong enough signal. In this case,
please use manual tuning.
5. To turn off the radio, hold the ON/OFF button until the radio
is turned off and the LED displays the time.
Note: The current station and volume will be memorised when
the radio is turned off, and will be played the next time the radio
is turned on.
For the best FM reception, extend the FM antenna wire to
its full length and move around to find the direction which
captures the strongest signal. Do not connect the FM wire
to an outdoor antenna.
For AM reception, extend the inbuilt antenna and turn the unit
to find the optimal direction.
PRESETTING RADIO STATIONS
You can preset up to 10 stations for each AM and FM,
these are stored as P01, P02, etc.
1. Tune the radio to the station you wish to preset.
2. Hold the preset button until the last memorised preset
number appears and flashes.
3. Select the desired preset number using the
P+ and P- buttons.
4. Once the desired preset number is displayed on screen,
press the PRESET button once to save.
Note: If the PRESET button is not pressed within 5 seconds
of reaching the desired preset number, preset mode will be
exited and the preset will not be saved.
If the chosen preset number is already saved, the existing
preset will be overwritten.
TUNING IN TO A PRESET STATION
1. When the radio is on, press either the PRESET, or P+ button
once to tune into the next preset.
2. Continually press the P+ or P- button to reach the
desired preset.
TIME SETTING
1. When the unit is first plugged in to the power outlet,
12:00 will appear and flash on the display.
2. Press the HOUR button to set the hour.
3. Press the MINUTE button to set the minutes.
4. Once the correct time is set, either press the TIME button
or leave for 5 seconds to save.
5. To adjust the current time, first switch off the radio. Hold the
TIME button until the display flashes, then set the time following
steps 2 - 4.
DUAL ALARM FUNCTION
This product allows the user to set dual alarms. These can be
set independently, waking up to either the radio or a buzzer.
When an alarm is set to radio, the user must select the desired
band, station and volume level before turning off the radio.
ALARM SETTING
1. To set the alarm time, the radio must be turned off.
2. Press the ALARM 1 button once, the alarm time and either
the Alarm 1 Buzzer or Radio indicator will flash.
3. Set the desired time using the HOUR and MINUTE buttons.
4. Once the desired time is set, either press the ALARM 1
button or leave for 5 seconds to save.
5. Press the ALARM 1 button repeatedly to set the alarm
function. The corresponding indicator be illuminated.
6. To set alarm 2, repeat steps 1 - 5 using the ALARM 2 button.
Note: Alarms 1 and 2 have unique buzzer sounds, allowing the
user to easily distinguish between the two alarms.
If the same time is set for both alarms, alarm 2 will take priority.
TURNING OFF THE ALARM
When the alarm sounds, press the ON/OFF or ALARM 1 button
to turn off alarm 1. Repeat with the ALARM 2 button to turn off
alarm 2. If a button isn’t pressed after the alarm sounds, it will
continue to sound and will turn off after 1 hour.
The alarm will sound again the same time the next day.
To disable the alarm, press the ALARM 1 or 2 button repeatedly
until no alarm indicators are illuminated.
SNOOZE SETTING
When the alarm sounds, press the SNOOZE button to turn off
the alarm. The alarm will sound again after 9 minutes. To switch
off the alarm while snoozing, press the ON/OFF button. The
alarm indicator will stop flashing and the alarm will sound again
the next day.
SETTING THE SLEEP TIMER
The sleep function allows the radio to play for 10, 20, 30, 40, 50,
60, 70, 80 or 90 minutes before turning off automatically.
1. Turn on the radio.
2. Press the SLEEP button repeatedly to select the desired
sleep time.
3. During sleep mode, press the SLEEP button to display the
remaining time. The sleep time can be set again following step
2.
4. To turn off sleep mode, press the SLEEP button repeatedly
until the LED displays OFF. The radio will continue to play until
turned off manually.