Buitink Technology BICS User manual

READ THE FOLLOWING INSTRUCTIONS AND WARNINGS TO AVOID SERIOUS INJURY
The BICS® is used as a protective measure against direct transfer of bodily uids, such as
sneezing, coughing and breathing. The BICS® will greatly reduce the chance on infection, but does
not completely eliminate the chance of infection.
WARNING: Always pay attention to road and trafc conditions when driving.
WARNING: The BICS® may obstruct the view while driving. The BICS® may glint by light sources,
such as the sun, other cars lights as well as interior lights. Always make sure there is enough
visibility while driving.
WARNING: The BICS® is to be assembled by adults only.
Ination: For best results, inate by using a low pressure air pump (such as a Bicycle pump).
Remove the air valve cap and insert the appropriate attachment of your ination device. Inate the
tube to 100% capacity or until almost rm. Close air valve by attaching the cap.
WARNING: Do NOT over inate tube, it may burst.
The BICS® is developed for use inside vehicles, without inuence of wheather conditions and UV
light. The material of the BICS® is sensitive to UV-light and can slightly change color (yellowish). It
is important to only use the BICS®inside vehicles and that they are properly stored in a dry place
when not in use. The BICS® should not be exposed to UV radiation and wheather inuences.
The BICS®can be cleaned and/or disinfected with most common cleaning agents up to a
concentration of 10 % at room temperature. Always ask the vendor of your BICS®screen whether
the cleaning agent and the concentration you have chosen is applicable to the material of the
BICS®! In case you use a cleaning agent, not applicable to the shield, it can irreversibly damage
the screen such that the visibility and transparency is reduced!. This can lead to dangerous trafc
situations!
When cleaning the BICS® inside the vehicle, be careful not to allow cleansing agent to leak into the
vehicle.
Part 2 >>
BICS®Vehicle screen instructions
Part 1
®

READ AND FOLLOW ALL SAFETY INSTRUCTIONS
- This is an inatable car screen – not a toy! To avoid risk of re, burns and personal injury, it
should not be placed where small children can reach it.
- Do not mount or place near gas or electric heaters, replaces, candles, or other similar
sources of heat.
- Do not secure product with staples or nails or place on sharp hooks or nails.
- Do not use this product for other than its intended purpose.
- Do not hang ornaments or other objects on the product.
- Store at room temperature, extreme temperatures can cause the inatable to become
defective.
- Maximum environment temperature when inated is 50°C/122°F, if used in higher
temperatures the inatable can become defective or, in worst case, even catch re.
- Avoid contact with hot or sharp objects.
- This is not a lifesaving device.
- Not for use by children.
- Do not use this product under the inuence of alcohol or drugs.
- Do not use the car screen after an impact or accident.
- Do not use tools to install the screen, the required fasteners are included.
Additional warnings:
- DO NOT over inate! Product should be rm, but allow a small depression when pushed on
with your hand.
- DO NOT drag across concrete, pavement or other rough surfaces. Unfold inatable at on
a clean surface free of debris and sharp objects.
- DO NOT store in direct sunlight.
- DO NOT inate with high-pressure air compressor.
WARNING: TUBE CAN EXPLODE IF OVER INFLATED
Make sure that the BICS® does not interfere with airbags or other safety equipment or other safety
requirements.
Do not use the BICS® at home. It has not been designed for home use and should only be used in
your vehicle. Never use the car screen without fastening the product securely, and never attempt to
use it without fastening into the vehicle. Do not add anything to the screen or modify it in any way.
The BICS® must not be used without fastening to the vehicle, as shown in the users manual.
Always use the fasteners that are delivered with the BICS®.
Please consult the users manual before use.
BICS®Vehicle screen instructions
Part 2
®

BICS®Vehicle screen instructions
Part 2
VS 2
Unfold inatable at on clean surface.
Inate BICS® screen using a low
pressure air pump or a bicycle pump.
Open box
Note: Do not use knife or other sharp
objects to open the box. The content is
very fragile.
Fit the inated screen in vehicle with valve at the
bottom right.
(Seen from the back seat -looking forward)
2x Velcro straps 5x D-rings 1x Valve
Fasten inated screen with included fasteners.
Fasteners are adjusteble in lenght using the robe
stopper. Find the proper position to xate the shield,
such that it is nicely tensioned.
max 30 cm
Fasten velcro straps around headrest
Have a save trip!
D-rings
Clip
Fasteners
1 2
3 4
5 6
BICS®Users manual
®