Bunn VPR Series Instruction and safety manual

S6161-L6-FSE-010
REVISION 2
TECHNICAL MANUAL
FOR
COFFEE MAKER, BUNN MODELS VPR & VPS
OPERATING AND SERVICE MANUAL
SUPERSEDURE NOTICE:THIS MANUAL SUPERSEDES S6161-FSE-010
REVISION 1, DATED 30 SEPTEMBER 2002, AND ALL CHANGES THERETO.
DISTRIBUTION STATEMENT A: APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED.
PUBLISHED BY DIRECTION OF COMMANDER, NAVAL SEA SYSTEMS COMMAND
*0910LP9841762* 01 DEC 2013

S6161-L6-FSE-010, Revision 2
01 DEC 2013
IDENTIFYING TECHNICAL PUBLICATION SHEET FOR
COMMERCIAL MANUAL
This manual supersedes S6161-L6-MMC-010 Revision 1, dated 30 September 2002, and all changes thereto.
1. PURPOSE: This technical publication sheet is issued for the purpose of identifying and authorizing the following
commercial manual for Navy use.
Manufacturer: Bunn O Matic Corporation
1400 Stevenson Drive
Springfield, IL 62703
Cage 25628
Purchase Order or Contract No.: P.O. 4500438046
Requisition No.: N/A
Equipment: Coffee Maker, Bunn Models VPR & VPS
National Stock Number: 0910-LP-984-1762
Title: Coffee Maker, Bunn Models VPR & VPS; Operating and Service Manual
Additional Identification: N/A
Date: 12/01/2013
1. ADDITIONAL COPIES: Additional copies are available from the Naval Logistics Library (NLL).
2. FILE LOCATION: The above-described commercial manual is filed in ________________________.
3. AUTHORITY NOTICE AND DISTRIBUTION STATEMENT:
Published by direction of Commander, Naval Sea Systems Command.
Distribution Statement A: APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED.
FOR UNCLASSIFIED MANUALS
NOTICE: Reproduction for non-military use of the information or illustration in this publication is not permitted.
The policy for military use reproduction is established in OPNAVINST 5510.1B.
This material may be reproduced by or for the U.S. Government pursuant to the rights acquired under Article 39 of
Newport News Shipbuilding Purchase Order DoD Contracts Appendix A dated March 2009.

This technical manual provides installation and parts list information for the Coffee Maker, Models VPR
& VPS, manufactured by Bunn O Matic Corporation. This manual is intended for guidance of and use by
personnel operating and maintaining the equipment described herein.
This manual consists of two parts as follows:
Part I - Serial Numbers 10053.0000G & 10784.0000G
Section I - Operating & Service Manual
Section II - Illustrated Parts Catalog
Part II - Serial Numbers 10053.001A, 41667.0000A, and 40667.0000D
Section I - Installation & Operating Guide
Section II - Service & Repair Manual
Section III - Illustrated Parts Catalog
Ships, training activities, supply points, depots, Naval Shipyards and Supervisors of Shipbuilding are
requested to arrange for the maximum practical use and evaluation of NAVSEA technical manuals. All errors,
omissions, discrepancies and suggestions for improvement to NAVSEA technical manuals shall be forwarded
to:
COMMANDER
CODE 310 TMDERs
NAVSURFWARCENDIV NSDSA
4363 MISSILE WAY BLDG 1389
PORT HUENEME, CA 93043-4307
on NAVSEA/SPAWAR Technical Manual Deficiency/Evaluation Report (TMDER), NAVSEA form 4160/1. All
feedback comments shall be thoroughly investigated and originators will be advised of action resulting
therefrom. One copy of NAVSEA form 4160/1 is at the end of each separately bound technical manual 8-1/2 x
11 inches or larger. Copies of NAVSEA form 4160/1 may be requisitioned from the Naval Systems Data
Support Activity Code 310 at the above address. Users are encouraged to transmit deficiency submittals via the
Naval Systems Data Support Activity Web site located at:
https://mercury.tdmis.navy.mil/def_external/pubsearch.cfm
FOREWORD
S6161-L6-FSE-010
FOREWORD-1/(FOREWORD-2 Blank)

SAFETY SUMMARY
GENERAL SAFETY NOTICES
The following general safety notices supplement the specific warnings and cautions appearing elsewhere
in this manual. They are recommended precautions that must be understood and applied during operation and
maintenance of the equipment covered herein. Should situations arise that are not covered in the general or
specific safety precautions, the commanding officer or other authority will issue orders as deemed necessary to
cover the situation. No work shall be undertaken on energized equipment or circuits until approval of the
commanding officer is obtained, and then only in accordance with Naval Ships’ Technical Manual (NSTM)
S9086-KC-STM-010/Chapter 300.
DO NOT REPAIR OR ADJUST ALONE
Under no circumstances shall repair or adjustment of energized equipment be attempted alone. The
immediate presence of someone capable of rendering first aid is required. Before making adjustments, be sure
to protect against grounding. If possible, adjustments should be made with one hand, with the other hand free
and clear of equipment. Even when power has been removed from equipment circuits, dangerous potentials
may still exist due to retention of charges by capacitors. Circuits must be grounded and all capacitors
discharged prior to attempting repairs. Equipment should be deenergized and properly tagged out according to
the ship’s Standard Operating Procedures.
TEST EQUIPMENT
Make certain test equipment is in good condition. If a metal-cased test meter must be held, ground the
case of the meter before starting measurement. Do not touch live equipment or personnel working on live
equipment while holding a test meter. Do not ground any measuring devices; these devices should not be held
when taking measurements.
INTERLOCKS
Interlocks are provided for safety of personnel and equipment and should be used only for the purpose
intended. They should not be battle shorted or otherwise modified except by authorized maintenance personnel.
Do not depend solely upon interlocks for protection. Whenever possible, disconnect power at the power
distribution source.
MOVING EQUIPMENT
Personnel shall remain clear of moving equipment. If equipment requires adjustment while in motion, a
safety watch shall be posted. The safety watch shall be qualified to administer CPR, have a full view of the
operations being performed, and have immediate access to controls capable of stopping equipment motion.
FIRST AID
An injury, no matter how slight, shall never go unattended. Always obtain first aid or medical attention
immediately, and file an injury report in accordance with OPNAVINST 5102.1 series, subj: Mishap
Investigation and Reporting.
S6161-L6-FSE-010
i

RESUSCITATION
Personnel working with or near high voltage shall be familiar with approved methods of resuscitation.
Should someone be injured and stop breathing, begin resuscitation immediately. A delay could cost the
victim’s life. Resuscitation procedures shall be posted in all electrically hazardous areas.
GENERAL PRECAUTIONS
The following general precautions are to be observed at all times.
a. Install and ground all electrical components associated with this system/equipment in accordance with
applicable Navy regulations and approved shipboard practices.
b. Ensure that all maintenance operations comply with Navy Occupational Safety and Health (NAVOSH)
Program Manual for Forces Afloat, OPNAVINST 5100.19 series.
c. Observe precautions set forth in NSTM S9086-KC-STM-010/Chapter 300 with respect to electrical
equipment and circuits.
d. Ensure that protective guards and shutdown devices are properly installed and maintained around
rotating parts of machinery and high voltage sources.
e. Do not wear loose clothing while working around rotating parts of machinery.
f. Ensure that special precautionary measures are employed to prevent applying power to the system/
equipment any time maintenance work is in progress.
g. Do not make any unauthorized alterations to equipment or components.
h. Before working on electrical system/equipment, use the correct tag out procedure and check with
voltmeter to ensure that system is not energized.
i. Consider all circuits ″live″and dangerous at all times, unless otherwise known to be ″dead.″
j. Do not use metal rules, flashlights, metallic pencils, or any other objects having exposed conducting
material when working near electricity.
k. Deenergize all equipment before connecting or disconnecting meters or test leads.
l. When connecting a meter to terminals for measurement, use range higher than expected voltage.
m. Before operating equipment or performing any tests or measurements, ensure area is dry of water or
other liquid conductive material and that frames of all motors and starter panels are securely grounded.
S6161-L6-FSE-010
ii

n. Ensure that area is well-ventilated when using cleaning compound or solvent. Avoid prolonged breathing
of fumes and compound or solvent contact with skin or eyes.
S6161-L6-FSE-010
iii

PART I
SERIAL NUMBERS
10053.0000G & 10784.0000G

SECTION I
OPERATING & SERVICE MANUAL
PART I / SECTION I

PART I / SECTION I

Page 1
TABLE OF CONTENTS
PAGE
Table of Contents 1
Introduction 2
User Notices 3
Electrical Requirements, Initial Set-Up, and Cleaning 4
Troubleshooting 5
Service 8
Schematic Wiring Diagrams (VPR & VPS) 15
Schematic Wiring Diagrams (VPRA & VPSA) 16
PART I / SECTION I

PART I / SECTION I