Burley ROOMSEALKIT User manual

Instructions for use with
the Universal Room
Sealing Kits
ROOMSEALKIT / ROOMSEALKIT90
SEALBOXKIT
for the Burley range of
Wood Burning Stoves
ApplicableAppliances:

Springdale (9103), Debdale (9104), Hollywell (9105),
Brampton (9108) and Wakerley (9112)
Owston (9303), Launde (9304), Bradgate (9305),
Swithland (9308) and Bosworth (9312)


Airsupply
Allhydrocarbonburningappliancesrequireanoxygen/airsupply.
If the stove is to be fitted on an external wall the air supplycanbetaken
straightfromtheoutside.A100mmdiameterholeneedstobedrilledinthe
correctplace(138mmabovethehearth)totakethe86mmexternal(80mm
internal)ductassupplied.
Thiswillallowforeasyconnection,anygapcanbefilledinwithcementor
mastic.
Aproprietarygrilleissuppliedwiththekit.
Iftheroomsealingkitisnotused,anairbrickornon‐closingventshouldbe
fittedtoensuretheairsupplyisnotblockedinanyway.
Ventilationisnotrequiredonthe3kW&4kWmodels.
Asideventoptiontotheroomsealingkitisavailable.

RoomSealingKit
Theroomsealingmethodofsupplyingairisalwaystobepreferredasheat
lossfromtheroomwillbegreatlyreducedthereforeincreasingthe
efficiencyoftheappliance.
Ifthestoveisnotonanoutsidewallorthedirectairsupplymethodcannot
beused,anairventmustbesuppliedintheroominwhichthestoveis
fitted.Thesizesoftheventsrequiredare:

3kW‐Noventrequired(Usingtheroomsealingkitwillincreaseefficiency)
4kW‐Noventrequired(Usingtheroomsealingkitwillincreaseefficiency)
5kW‐550mmsqrequired(Forhomesbuiltbefore2010noairventrequirement.)
8kW‐1650mmsq(50mmdiameter)
12kW4950mmSq(100mmdiameter)

Onlypermanentlyopenventscanbeusedandconsiderationshouldbegiven
todraughtwhenthestoveisnotinuse,thereforesitethisventcarefully.
TheventcoversshouldcomplywithBuildingRegulationsPartJandshould
besitedwheretheycannotbeblocked.

Room Sealing Kit Contents:
1 X PLENUM BOX
2 X M8 NUTS
2 X M8 WASHERS
1 X 80MM
DIAMETER DUCT
1000MM LENGTH
1 X SLIDING
BAFFLE
1 X VENT COVER
* Not included
with
SEALBOXKIT
* Not included with
SEALBOXKIT

UNDO AND REMOVE THE NUT AND TWO WASHERS.
REMOVE THE AIR CONTROL PLATE.
1.
Fitting Instructions

INSERT SLIDING BAFFLE INTO
THE PLENUM BOX WITH THE
SLOTTED EDGE CLOSEST TO
THE PLENUM BOX FLANGE
2.
3.
INSERT THE AIR CONTROL
PLATE ( REMOVED FROM THE
STOVE IN SECTION 1) THROUGH
THE SLOT IN THE SLIDING
BAFFLE.

INSERT THE END OF THE
AIR CONTROL PLATE INTO
THE AIR CONTROL
ARM.
4.
5.
ATTACH THE AIR
CONTROL PLATE AND
NUT WITH SUFFICIENT
TENSION TO ENABLE
THE SMOOTH OPERATION
OF THE MECHANISM.

6.
MOUNT THE PLENUM BOX ONTO THE FIXING
STUDS AND SECURE WITH THE 2 X M8 NUTS AND
WASHERS.
CUT THE DUCT TO THE LENGH REQUIRED AND
LOCATE ONTO THE SPIGOT ON THE PLENUM
BOX. USE THE LOCKING SCREW TO SECURE
THE DUCT.
FIT THE VENT COVER ON THE EXTERNAL WALL.


MadeintheUK










BurleyAppliancesLtd
LandsEndWay
Oakham
Rutland
LE156RB
UnitedKingdom


Email:[e-mail]
Phone:01572756956
Fax:01572724390
UpdatedOctober2016