Burlington C24 User manual

C
Parts supplied:
1 - 5
●Please read these instructions carefully to avoid damage
to the valves, and to ensure correct installation.
●Do not use bleach or bleach based cleaning products in
the cistern, as these will cause damage to the seals.
We cannot be held responsible or liable for any failure
which results from the use of bleach based products.
●Water temperature range +2C to +45C.
●Water pressure 0.2 to 8 bar.
Flush Valve
1x 1x
1x
InletValve
Plug
2x
Bolt
1x
Flush Cone
1x
Fixing Nut
1x
Plastic
Washer
1x
Cone Washer
1x
Flush Cone
Lever
1x
Burlington 510mm close coupled cistern tank
with back and bottom entry water supply with lever flush
1: Flush Valve installation
evlaVhsulF
ydoB
evlaVhsulF
taeS
dnatunehtnwodwercS
.srehsawehtffoekat
rehsawrebbuR
rehsawcitsalP
F tungnixi
rehsawrebbuR
esabevlavhsulF
epipwolfrevO
htiwdehcattaesabevlavhsulftresnI
.elohhsulfnretsicotnirehsawrebbur
,rehsawrebburehtllatsninehT
ehtnethgitdna,rehsawcitsalp
.tungnixif
C24
Burlington Extended depth 510mm close coupled cistern tank
with back and bottom entry water supply with lever flush C30

C
3: Installation Option for Close coupled or Low level
4: Flush Valve trouble shooting
1.Install again according to the correct installation procedure.
3.Disconnet and wash flush valve body.
Adjust water level.
Half flush water level is too high or too low. Water level is adjusted incorrectly.
Cable is distorted.
3.Flush valve body is stuck.
2.Flush valve seat does not fit flush valve body.
1.Incorrect installation.
No flush, low flush or half flush volume
Problem
Leakage
2.Install again.
noituloSnosaeR
Remove kinks or sharp bends in the cable.
2 - 5
evlaVhsulF
ydoB
noitallatsnIevlaVhsulFdelpuoCesolC
hsulF
evlaV
nretsiC
noitallatsnIevlaVhsulFleveLwoL
Use the brass nut from Low Level kit to fix the Flush Valve.
ssarB
tun
Note: The Flush Valve should be adjusted for the required flush volume.
The diagram “A”
below indicates the correct setting for 6L full flush and 3L half flush.
The diagram “B” below indicates the correct setting
is for 4.5L full flush and 2.6L half flush.
2: Flush Valve scale and adjustment setting
hsulfflahL3dnahsulfllufL6
123
Half Flush Float : should be set on the 1 mark.
Full Flush Adjustor : should be set at 2 mark.
Half Flush Adjustor : should be set at 1.5 mark.
A
hsulfflahL6.2dnahsulfllufL5.4
123
Half Flush Float : should be set on the 2 mark
Full Flush Adjustor : should be set on the 5mark
Half Flush Adjustor : should be set at 4.5 mark
B
lf,nwodtaolfevoM ulovhsu .sesaercniem
.sesaercedemulovhsulf,putaolfevoM
taolfhsulfflaH
rotsujdahsulflluF
.sesaercniemulovhsulf,nwodrotsujdaevoM
edemulovhsulf,putaolfevoM .sesaerc
rotsujdahsulfflaH
.sesaercniemulovhsulf,nwodrotsujdaevoM
utaolfevoM .sesaercedemulovhsulf,p
2
3
1
2
1
3
2
1
3
enoChsulF
,tungnixifehtrevoenochsulfehthsuP
e onsierehtdna,talfsititahterusn
.napdnanretsicneewtebegakael
otgulpehtesuesaelP
telnimottobehtkcolb
.eloh
otgulpehtesuesaelP
telnimottobehtkcolb
.eloh
kcolbotstlobetihwowtehtesU
.selohnoitallatsniowteht
hsulfflahL6.2dnahsulfllufL5.4
123
Half Flush Float : should be set on the 2.5 mark
Full Flush Adjustor : should be set on the 5.5 mark
Half Flush Adjustor : should be set at 1.5 mark
B
2
1
3
123
Half Flush Float : should be set on the 2.5 mark
Full Flush Adjustor : should be set on the 5 mark
Half Flush Adjustor : should be set at 1.5 mark
A
2
1
3
hsulfflahL3dnahsulfllufL6
C24 Burlington 510mm close coupled cistern tank
C30 Burlington Extended depth 510mm close coupled cistern tank

C
.dorgnixifehtnesooL
.61otelacsehttsujdA
dorgnixiF
1: Inlet Valve adjustment settings and Installation
2: Filter cleaning (Please clean periodically)
Leakage
Inlet Valve does not work Clean the filter.
Tighten the nut.
The filter is blocked.
Water supply is closed.
Incorrect water level
Problem Solution
Open the water supply
Adjust the Water level correctly..
Readjust the direction of the inlet valve.
The Stop Float is pressed by the tank.
.
The Inlet Valve fixing nut has not been tightened.
Incorrect adjustment.
Reason
3:
Inlet Valve trouble shooting
Close the water supply, and take off the
inlet valve.
Screw down the fixing nut, and take off the water
supply pipe.
Filter
Clean by rinsing the filter.
3 - 5
evlavtelnI
tekcarB
tekcarB
tekcarB
dorgnixiF
epipwolfrevO
wolfrevoehtotnoevlavtelniehtxiF
.dorgnixifehtnethgitdna,epip
.dneylppusehtotepipylppusretawehttcennoC
.llewskrowevlavtelniehtfikcehC,ylppusretawehtnepO
.detsujdaebdluoclevelretaweht,deriuqerfI
:dorehtgnitsujdA
hsulfehtdnasesirlevelretawehtesiwkcolcgnitsujdayB:A
.sesaercniemulov
hsulfehtdnasllaflevelretawehtesiwkcolc-itnagnitsujdayB:B
.sesaercedemulov
nretsiC
Inlet pipe
Fixing nut
Filter
evlavtelnI
tekcarB
nretsiC
Reinstall the inlet valve.
doRtnemtsujdA
elacs"61"
16
16
14
14
12
10
8
6
2
0
4
nretsiC
elacs"61"
16
16
14
14
12
10
8
6
2
0
4
6L full flush and 3L half flush,
Adjust the scale to 16.
4.5L full flush and 2.6L half flush
Adjust the scale to 13.
C30 Burlington Extended
depth 510mm close
coupled cistern tank
C24 Burlington 510mm
close coupled cistern
tank

C
1: Install Close Coupled Cistern To Pan
2: Install Lever
4 - 5
Note:
After installation check that the full flush and half flush are working correctly.
Please consult the trouble shooting pages if there are any problems.
ehtnotolsehtdnadrawtuognicafrevelehthtiW*
.nretsicotrevelehtxif,sdrawpugnicafdaerht
* The fixing nut should be
tightened as much as
possible to avoid the
cistern lever working
loose during operation.
* Raise the lever so that
it fits into the flush box in
the correct position.
* Make sure the cable is not
distorted or kinked.
Insert the box and
tighten the nut.
noitceriDB
B
hsulF
xoBnottuB
tuNgnixiF
noitator-itnA
rehsaW
tuN
reveL
eloHreveLnretsiC
daerhTehTnItolS
rehsaWcitsalP
rebbuR
rehsaW
lluP
nethgitdnanwohssanretsicehtllatsnI
.stungnixifeht
1
.nretsicehtotylppusretawehttcennoC
2
Close Coupled Cistern & Flush Level Installation
Fixing nut
Plastic washer
Rubber washer
* Please ensure the flush cone is in position before
installation.
* The overflow pipe of
flush valve may be cut
down depending on the
installation on site.
Please ensure the fill rate
of the cistern does not
exceed the flow capacity of
the overflow pipe.

C
Low Level Cistern Installation
5 - 5
Note:
Please carefully check for leaks after installation.
Please use two white bolts to block the two fixing holes on the bottom of
cistern, cut the bolts to suitable length if necessary.
,noitallatsninretsicdnanapehtfonoitacoltcaxeehtenimreteD
.yrassecenfiylgnidroccaepiPhsulFehttucneht
.margaidehtninwohsecneuqesehtninretsicehtotniepiPehttiF
epiPhsulFehtybdewollof,napehtotnienoChsulFehttresninehT
.margaidehtninwohssa
eloHtelnI
enoChsulF
naP
nretsiC
teltuO
ahSenoC dep hsaW re
rehsaWcitsalP
tuNgnixiF
revoCevitaroceD
epiPhsulF