BURREL 077-870-0300 User manual

Operating Manual for
Hotplate and
Hotplate Stirrer
Item # 077-870-0300 and #077-870-00-020
Burrell Scientific, LLC
1010 Jackson's Pointe Court
Zelienople, PA 16063
800-732-8484 | [e-mail]

2
OPERATIONS MANUAL
Please read the User Manual carefully before use, and
follow all operating and safety instructions!
INTRODUCTION
Thank you for choosing Burrell Scientific as you your source for laboratory equipment. This
manual covers the Burrell Scientific line of digital Hotplates and Hotplate/Stirrers. In order to
ensure the safe operation of the equipment enclosed, please read this manual in its entirety
before use.
INSTALLATION
1. Prior to installation, ensure all components are included in the carton and have arrived
as expected.
2. Contact Burrell Scientific at 800-732-8484 or [email protected] as soon as possible
should there be any discrepancy or damage.
3. Place your new Hotplate or Hotplate/Stirrer on a flat, nonslip, level surface with at least
4 inches (10cm) clearance on all sides. If desired, attach the optional support rod to the
rear of the unit by screwing threaded end into designated hole.
4. Attach proper power cord to the rear of unit and plug into a grounded outlet of
appropriate voltage.
VOLTAGE OF OUTLET MUST MATCH VOLTAGE LISTED ON THE LABEL ON THE
REAR OF THE INSTRUMENT. FAILURE TO SUPPLY APPROPRIATE POWER MAY
DAMAGE INSTRUMENT AND VOID WARRANTY.

3
OPERATION (HOTPLATE/STIRRER COMBINATION)
1. Turn power switch (rear of instrument) to ON position.
2. Set stir speed by turning the dial. The set stir speed will appear on the top of the display.
To operate without stirring, set stir speed to zero.
3. Set temperature by using the up & down keys beneath the display. The set temperature
will appear on the bottom of the display. To operate without heating, set temperature
to zero.
4. Once desired stir speed and temperature are set, press the selection knob to begin
stirring and heating. The actual stir speed and temperature will begin to rise to the set
parameters. Hot surface indicator lights at 50°C.
CAUTION: HOT SURFACE
Once selection knob has been pressed, the surface of the instrument will begin to heat. Avoid
bodily contact or personal injury may occur.
CONTROL PANEL
A) Hot surface indicator light –Safety
Warning
B) Digital Display
C) Temp. selection keys
D) Speed control dial
E) Start/Stop
If you encounter any problems with the installation or initial operations of this unit, please
contact us at: 800-732-8484 or [email protected].

4
OPERATION (HOTPLATE)
1. Turn power switch (rear of instrument) to on position.
2. Set temperature by turning the dial on the right.
3. Set temperature will appear on bottom of display, with actual surface temperature
appearing on top of display.
4. Once desired temperature is set, press selection knob to begin heating. The actual
temperature (top of display) will rise to match the temperature set on the bottom. Hot
surface indicator lights at 50°C.
CAUTION: HOT SURFACE
Once selection knob has been pressed, the surface of the instrument will begin to heat. Avoid
bodily contact or personal injury may occur.
CONTROL PANEL
A) Hot surface indicator (Hotplate only)
B) Digital Display
C) Temp. control dial
D) Start/Stop
Should any damage occur in shipment, do not operate and please notify us at:
800-732-8484 or [email protected].

5
MAINTENANCE AND CLEANING
To ensure performance and longevity of the instrument, keep outer body and surface plate
clean. Disconnect hotplate from power source and use a lint free cloth to wipe down all
surfaces when cool. Do not immerse in water or spray cleaner directly on the instrument.
The instrument is covered by a 1 year limited warranty. In the event of failure or defect,
disconnect the unit from the power source and contact Burrell Scientific.
SPECIFICATIONS
Speed
200-1500 rpm*
Temperature
Ambient +5° - 380°C*
Platform Dimensions
6.5” by 6.5”
Electrical
115V/60Hz or 230V/50Hz
Power Consumption
Max: 500W
Warranty
1 Year
TROUBLESHOOTING
Concern: Not heating or not stirring
Check:
Troubleshooting:
Power Supply Cord
Plug firmly into socket
Check Fuse
Replace fuse

6
NOTES
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
______________________________________________
______________________________________________
______________________________________________
______________________________________________
______________________________________________