C. Crane CC Vector Technical manual

Quick Start Setup Guide
NOTE: Please follow the Assembly Guide and Mounting Instructions for
your Supplied USB Antenna.
To Configure with a Ethernet Cable:
Although the CC Vector can be set up from a tablet or a smartphone, it may be
easier to use a computer using the included 18” Ethernet cable.
Connect the Ethernet cable to your computer’s Ethernet port and to either of the
CC Vector’s Ethernet ports on the back of the device.
Configure Wirelessly (most popular way):
1. From your computer, tablet, smartphone or
WiFi device, go to the WiFi Settings/Connections
and connect to the WiFi Name listed
on the sticker underneath the CC Vector.
2. Enter the WiFi Password when prompted.
1
WiFi Name
WiFi Password
NOTE: Please do not skip any steps.
START HERE: Attach Repeater’s
Antenna
Plug AC Power
into Wall
Connect Power
Rev 14_4/2018
CC Vector
WiFi Repeater
OR
B1
AA
B2
Leave this one
unplugged
Connect other end of the USB cable to the USB Antenna.
Plug USB into
the CC Vector

2
After confirming you have completed Step “B”, open the Internet Browser screen on your
device and enter 192.168.8.1 into the Address Bar. Press “Enter” on your keyboard.
NOTE: At this point you are connected to the CC Vector but your browser will likely
tell you that you are not connected to the internet. This is normal because the CC Vector
is not yet setup. Continue with the setup.
NOTE: For best performance, your signal should be higher than 50%. For a better signal,
try adjusting the orientation and placement of the USB antenna - then click “Rescan” to
see if the signal is higher.
NOTE: If network in Step “D” does not require a password, then you will not get this
screen. Proceed to Step “F”.
NOTE: If wireless password includes special characters please see #2 in the
“Troubleshooting and Tips” section on Page 3.
..then click
”Next”
and go to
Step “F”
Enter Wireless
Password for
Network
in Step “D”
For
advanced
users only
..then click
”Select”
Click the
dot next to
the WiFi
network that
you want
to repeat..
C
D
E

3
The system will reboot. Please make sure your
computer, phone or tablet stays connected to
“CCrane” and does not automatically connect
to another WiFi network. If no response after 1
minute then close and re-open your web browser
screen.
You should now see a screen similar to this:
If “Status” is “Connected” and “Internet Access” is “Yes”, then you are finished with the setup.
Bookmark this page with your web browser in case you need to return to it to check the
connection or change networks. You can now close this screen and continue using the
internet normally.
2. For wireless networks that use spaces or special characters in the Wireless
Password such as (!@#$%^&*_), follow the instructions below:
a. Follow the included Quick Start Setup Guide to step “E”.
b. Select “Configure Manually”.
c. Select “Site Survey”.
d. Select your desired network with the existing internet connection.
e. Click “Select”.
f. Enter your wireless password in the “Pass Phrase” text box.
g. Select “Next” (you may have to use the arrow to scroll to the right to see “Next”).
h. Then select “Done”.
Troubleshooting and Tips
F
G
If “Status” is “Connected” and “Internet Access”
is “No”, please wait for 5 to 10 minutes.
If no change, please see “Troubleshooting and
Tips” #3.
1. No “Network Names” are showing under the titles for Step “D” in the Site Survey.
a. No WiFi networks in range of the USB WiFi Antenna. Try moving or re-adjust the USB
WiFi Antenna.
b. Check to make sure that the small USB connector of the USB cable is properly inserted
fully into the USB Antenna connector.
c. Make sure to use the main USB connector of the USB cable and it is inserted into the
USB Port of the CC Vector Repeater. After above is checked, click Rescan. Call C. Crane
at [phone] if you are still not able to see any “Network Names” in Step “D”.

4
Copyright ©2018 by C. Crane Company, Inc.
172 Main Street, Fortuna, CA 95540 • Phone: [phone] • Web: ccrane.com
All rights reserved. No part of this booklet may be reproduced, in any form or means whatsoever without permission in writing from C. Crane Company, Inc.
Additional Tips
4. For a wireless network that has a hidden Network Name (SSID), follow the instructions
below:
a. Follow the included Quick Start Setup Guide to step “D”.
b. Select “Manual Setup” from the gray bar (at the top of the page).
c. Select “USB Wireless adapter”.
d. Select the “SSID” text box and enter the name (SSID) of your desired network with the
existing internet connection.
e. Select Network Type “Infrastructure” from the drop-down list.
f. Select the correct Security Mode from the next drop-down if you have a hidden network.
g. You will need to know ALL the correct wireless security information related to the selected
network. In some cases you may be able to find the correct security information by selecting
the hidden network from “Site Survey”. You will still need to know and enter the correct
Wireless Password or Passphrase.
h. Select “Next” (you may have to arrow over to scroll the screen to the right to see “Next”).
i. Then select “Done”.
Troubleshooting and Tips - Continued
3. The “Status” shows “Connected” and “Internet Access” shows “No”
In some cases, if you are at a public WiFi such as an RV Park, Hotel, Hospital, coffee shop,
etc. that requires a Username & password, or to accept the User’s Terms and Agreement,
open your browser and follow their instructions.
• Some devices such as smartphones, tablets, printers, etc. offer WPS
as an alternate form of WiFi connection which does not require a password.
To connect devices to the CC Vector without entering a password, press
the “WPS” button when prompted by your device to connect.
Check the WPS instructions for your computer or WiFi device.
• For best performance we recommend 5 to 15 feet of separation between the CC Vector
and the USB Antenna.
• In some cases you may receive faster WiFi by rotating the USB Antenna horizontally, making
sure to aim the broad side towards the distant WiFi network.
• It is normal to receive some speed reduction when repeating a WiFi network. (Because it
has to deliver the signal twice).
“WPS” button