C-me EasyTel User manual

5
Thank you for choosing CME.
This simplified universal remote control contains all the main
functions of most TV remote controls of
the brands listed on the back.
Insert the batteries and program your remote control
before using it.
Keep your Instructions Booklet for future reference.
USING THE KEYS AND FUNCTIONS
GB
FITTING THE BATTERIES
The remote control requires 2 new
AAA/LR03 alkaline batteries.
Insert the batteries as shown:
• Batteries must be changed once a year.
• Change the batteries if the light indicator starts to flash during use.
The batteries are low.
• When removing batteries, insert the new ones within 5 minutes or
you may have to reprogram your remote control.
• Make a note of the code for your TV on the adhesive label supplied
inside the battery compartment cover. This note will be handy if you
have to reprogram your remote control.
Mute key.
Control the volume
using +/-.
ON/OFF per
spegnere il TV e
in alcuni casi per
accendere il TV.
To select the
previous programme
or to turn ON
your TV.
Press them together to
turn ON your TV on
programme 1.
To select an
external terminal.
Light indicator.
To select the next
programme or to turn
ON your TV.

6
1.Make sure that the TV is ON.
2.Hold down the and
keys simultaneously until
the light indicator at the top
starts to flash indicating
that the remote control is
in programming mode.
3. Press key four times
then point the remote
control at the appliance.
Press and release the
key slowly several times.
STOP when your TV goes
OFF.
4.When your TV is OFF, press
the and keys
simultaneously. When you
release the keys, three
flashes indicate that the
search operation has been
completed correctly.
5.
IF YOU DO NOT HAVE THE
PROGRAMME SELECTION
KEYS ON YOUR ORIGINAL
REMOTE CONTROL
If your remote control does
not have the programme
selection keys (e.g. / ,
+/-, CH+/-..etc) once you
have programmed Easytel,
you can still select the
programmes from 0 to 9, as
follows:
SET-UP
Read these instructions carefully before programming
your remote control!
To use the remote control with your appliances, you must first
program Easytel as described below. You can also visit our
Internet site www.cme.it to have access to interactive
instructions for easier and faster
remote control programming.
PROGRAMMING YOUR REMOTE CONTROL
•Hold down the and
keys simultaneously until
the light indicator starts to
flash indicating that the
remote control is in
programming mode.
•Release the keys and
press 8 times within
12 seconds.
Three flashes indicate that
the operation has been
completed correctly.
•Make sure you can change
programmes from 0 to 9
using the and keys.
If not, repeat the search
operation, starting from
point 2.
Additional check
Check that all 7 keys are
operating correctly. If the
commands work incorrectly
or erratically, you have
probably entered a code for a
similar but different remote
control.
In this case, repeat the search
procedure from point 2 until
all keys respond correctly to
the commands sent.
P
-
P
-
+
P
P
-
+
P
+
P
AV
AV
AV
Identify and take note of the TV code which you have
searched for, following the code noting procedure
(see "PROGRAMMED CODE NOTING" section).

7
NOTE: DURING THE SEARCH OPERATION, THE LIGHT
INDICATOR FLASHES MORE QUICKLY. THE LIGHT
INDICATOR STOPS FLASHING AND YOUR REMOTE
CONTROL LEAVES PROGRAMMING MODE IN THE
FOLLOWING CASES:
•if no keys are pressed for 12 seconds
•if you press keys other than those indicated
•if the code search list is completed. In this case, visit
www.cme.it or contact the call center.
RE-PROGRAMMING YOUR REMOTE CONTROL
BY ENTERING THE CODE NOTED DOWN
If the remote control is no longer programmed because it has
been left without batteries for a long time or has flat batteries,
you can re-program it quickly as follows:
1.Hold down the and keys simultaneously until the
light indicator at the top starts to flash indicating that the
remote control is programming.
2.Release the keys and, within 12 seconds, using the
and keys, enter the eight-sign code which you noted
down before. At the end, three flashes indicate that the code
has been saved correctly. If not, try the code entry procedure
again from point 1.
When you have programmed Easytel CME, note down the
code on the label in the battery compartment cover.
To find the code for your remote control:
1. Hold down the and keys simultaneously until the light
indicator at the top starts to flash indicating that the remote
control is searching for the code.
2. Release the keys and, within 12 seconds, press and
simultaneously.
3. Release and and pay attention to the flashing of the
LED: a long flash corresponds to a +while a short flash
corresponds to a -. Note the sequence of the 8 flashes and
note them down on the label in the battery compartment
cover, from left to right.
PROGRAMMED CODE NOTING
Once you have programmed Easytel, you can turn ON
your TV in three ways:
•Press or .
•Press .
•Press and simultaneously: this sends the code
for programme 1.
To return to programme 1 directly, press and
simultaneously.
USING YOUR REMOTE CONTROL
P
-
+
P
P
-
+
P
P
-
+
P
P
-
+
P
P
-
+
P
P
-
+
P
AV
AV

8
WARRANTY: 2 years
The warranty ceases to be valid if the product is tampered with or
used incorrectly.
Remote control model Easytel
Purchase date
Agent's stamp
PROBLEM
The TV does not respond
and the light indicator does
not light up when you press
a key.
The TV or VCR does not
respond but the light
indicator does light up.
The TV does not respond
and the light indicator
flashes.
Not all remote control
commands are working
correcting.
The and keys do not
select the programmes.
TROUBLESHOOTING
SOLUTION
Check that the batteries are
fitted correctly. If necessary,
replace them with 2 new 1.5 V
AAA/LR03 alkaline batteries.
Check that the batteries are new
and that the remote control is
pointing at the appliance without
any obstacles in the way. If
required, reset the remote
control code by repeating the
programming procedure.
Batteries are low. Replace them.
You may have used the wrong
code. Reset the remote control
code, following the programming
procedure.
The original remote control may
not have had this function. In
this case, set the code (press
8 times) as described in the
PROGRAMMING YOUR
REMOTE CONTROL section
above.
If you have any queries about Easytel:
•read this booklet carefully – this will help you to solve
almost all problems
•consult our Internet site www.cme.it to answer all your
queries more easily and quickly.
INFO-LINE
P
-
+
P
+
P