Cabletron Systems SmartCell 6A000 Assembly instructions

SmartSwitch 6A000
Installation and Setup
Guide
35 Industrial Way
Rochester, NH 03866
USA
[phone]
Part Number 04-0056-01 Rev. A
Order Number 9033005

ii SmartSwitch 6A000 Installation and Setup Guide
NOTICE
Cabletron Systems reserves the right to make changes in specifications and other information contained in this
document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any
such changes have been made. The hardware, firmware, and software described in this manual are subject to change
without notice.
IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL,
OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING, BUT NOT LIMITED TO, LOST PROFITS)
ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED IN IT, EVEN IF
CABLETRON SYSTEMS HAS BEEN ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE
POSSIBILITY OF SUCH DAMAGES.
Copyright 1998 - 99 by Cabletron Systems, Inc., P.O. Box 5005, Rochester, NH 03866-5005
All Rights Reserved
Printed in the United States of America
SmartSwitch 6A000 Installation and Setup Guide
Part Number 04-0056-01 Rev. A
Order Number: 9033005
SmartSwitch, SPECTRUM, LANVIEW, MicroMMAC, and BRIM are registered trademarks and Element Manager,
EPIM, EPIMA, EPIM-F1, EPIM-F2, EPIM-F3, EPIM-T, EPIM-X, FOT-F, FOT-F3, HubSTACK, SEH, SEHI, and
TMS-3 are trademarks of Cabletron Systems, Inc. All other product names mentioned in this manual may be
trademarks or registered trademarks of their respective companies.

SmartSwitch 6A000 Installation and Setup Guide iii
FCC CLASS A NOTICE
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Note This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment uses, generates, and can
radiate radio frequency energy and if not installed in accordance with the
SmartSwitch6A000InstallationandSetupGuide,maycauseharmfulinterference
to radio communications. Operation of this equipment in a residential area is
likely to cause interference in which case the user will be required to correct the
interference at his own expense.
Caution Changes or modifications made to this device which are not expressly approved
by the party responsible for compliance could void the user’s authority to
operate the equipment.
DOC CLASS A NOTICE
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the
Radio Interference Regulations of the Canadian Department of Communications.
Le present appareil numerique n’emet pas de bruits radioelectriques depassant les limites applicables aux appareils
numeriques de la class A prescrites dans le Reglement sur le brouillage radioelectrique edicte par le ministere des
Communications du Canada.

iv SmartSwitch 6A000 Installation and Setup Guide
DECLARATION OF CONFORMITY
ADDENDUM
Application of Council Directive(s): 89/336/EEC
73/23/EEC
Manufacturer’s Name: Cabletron Systems, Inc.
Manufacturer’s Address: 35 Industrial Way
P. O. Box 5005
Rochester, NH 03866
Product Name: SmartSwitch 6A000
European Representative Name: Mr. J. Solari
European Representative Address: Cabletron Systems, Limited
Nexus House, Newbury Business Park
London Road, Newbury
Berkshire RG13 2PZ, England
Conformance to Directive(s)/Product Standards: EC Directive 89/336/EEC
EC Directive 73/23/EEC
EN 55022
EN 50082-1
EN 60950
Equipment Type/Environment: Networking Equipment, for use in a Commercial or Light
Industrial Environment.
We the undersigned, hereby declare, under our sole responsibility, that the equipment packaged with this
notice conforms to the above directives.
Manufacturer: Full Name: Mr. Ronald Fotino
Title: Principal Compliance Engineer
Location: Rochester, NH. U.S.A.
Legal Repersentative in Europe: Full Name: Mr. J. Solari
Title: Managing Director - E.M.E.A.
Location: Newbury, Berkshire, England

SmartSwitch 6A000 Installation and Setup Guide v
SAFETY INFORMATION
CLASS 1 LASER TRANSCEIVERS
The IOM-29-4-MIX, IOM-29-4-IR, IOM-29-4-LR, IOM-39-1 and IOM-39-1-LR connectors use Class 1 Laser
transceivers. Read the following safety information before installing or operating one of these modules.
The Class 1 Laser transceivers use an optical feedback loop to maintain Class 1 operation limits. This control loop
eliminates the need for maintenance checks or adjustments. The output is factory set, and does not allow any user
adjustment. Class 1 Laser transceivers comply with the following safety standards:
•21 CFR 1040.10 and 1040.11 U. S. Department of Health and Human Services (FDA).
•IEC Publication 825 (International Electrotechnical Commission).
•CENELEC EN 60825 (European Committee for Electrotechnical Standardization).
When operating within their performance limitations, laser transceiver output meets the Class 1 accessible emission
limit of all three standards. Class 1 levels of laser radiation are not considered hazardous.
LASER RADIATION AND CONNECTORS
When the connector is in place, all laser radiation remains within the fiber. The maximum amount of radiant power
exiting the fiber (under normal conditions) is -12.6dBm or 55x10-6 watts.
Removing the optical connector from the transceiver allows laser radiation to emit directly from the optical port. The
maximum radiance from the optical port (under worst case conditions) is 0.8 W cm-2 or 8x103W m-2 sr-1.
Do not use optical instruments to view the laser output. The use of optical instruments to view laser output increases
eye hazard. When viewing the output optical port, you must remove power from the network adapter.

vi SmartSwitch 6A000 Installation and Setup Guide
FIBER OPTIC PROTECTIVE CAPS
Warning READ BEFORE REMOVING FIBER OPTIC PROTECTIVE CAPS.
Cable assemblies and MMF/SMF ports are shipped with protective caps to prevent contamination. To avoid
contamination, replace port caps on all fiber optic devices when not in use.
Cable assemblies and MMF/SMF ports that become contaminated may experience signal loss or difficulty inserting
and removing cable assemblies from MMF/SMF ports.
Contamination can be removed from cable assemblies by:
1. Blowing surfaces with canned duster (Chemtronics p/n ES1270 or equivalent).
2. Using a fiber port cleaning swab (Alcoa Fujikura LTS p/n ACT-01 or equivalent) saturated with
optical-grade isopropyl alcohol, gently wipe the end surface of ferrules first; then wipe down the
sides of both ferrules.
3. Blow ferrule surfaces dry with canned duster.
Contamination can be removed from MMF/SMF ports by:
1. Using the extension tube supplied with canned duster, blow into the optical port, being careful not
to allow the extension tube to touch the bottom of the optical port.
2. Reconnect cable and check for proper mating.If problems remain, gently wipe out optical port with
a DRY fiber port cleaning swab and repeat step 1.
Warning To avoid contamination, replace port caps on all fiber optic devices when not
in use.

SmartSwitch 6A000 Installation and Setup Guide vii
REGULATORY COMPLIANCE SUMMARY
SAFETY
The SmartSwitch 6A000 meets the safety requirements of UL 1950, CSA C22.2 No. 950, EN 60950, IEC 950, and
73/23/EEC.
EMC
The SmartSwitch 6A000 meetsthe EMC requirementsof FCC Part 15,EN 55022, CSA C108.8, VCCI V-3/93.01, EN
50082-1, and 89/336/EEC.

viii SmartSwitch 6A000 Installation and Setup Guide
REVISION HISTORY
Document Name: SmartSwitch 6A000 Installation and Setup Guide
Document Part Number: 04-0056-01 Rev. A
Document Order Number: 9033005
Author: Bruce Jordan
Editor: Ayesha Maqsood
Illustrator: Michael Fornalski
Date Revision Description
>ÀV…Ê£™™™ £ Initial release
First revision

SmartSwitch 6A000 Installation and Setup Guide ix
Table of Contents
TABLE OF CONTENTS
1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
2 Switch Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.1 Unpacking the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.1.1 Accessory Carton Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.2 Inspecting the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.3 Installing the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . 2-3
3 Configuring the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.1 Switch Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.1.1 Backup Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
3.2 Using the Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
3.2.1 Port Numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
3.2.2 Console Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
3.2.3 Console Time-out. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
3.2.4 Creating an Alias . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
3.2.5 Ambiguous Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
3.2.6 Console Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
4 ATM Administrator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4.2 Starting ATM Administrator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
4.3 Managing Your ATM Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
4.3.1 ATM Connectivity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
4.3.2 Accessing Online Help. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
5 Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
5.1 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
5.2 Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
A Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
A.1 Telephone Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-1
A.2 FAX Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-1
A.3 Electronic Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-1
A.4 Placing A Support Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-1
A.5 Hardware Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-2
A.6 Software Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-2

x SmartSwitch 6A000 Installation and Setup Guide
Table of Contents
A.7 Repair Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

SmartSwitch 6A000 Installation and Setup Guide xi
List of Figures
LIST OF FIGURES
Figure 2-1 6A000-04 and 6A000-02 front panels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Figure 2-2 Installing the SmartSwitch 6A000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . 2-5
Figure 3-1 SmartSwitch 6A000 console and network connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Figure 4-1 ATM Administrator physical topology view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Figure 4-2 ATM Administrator PNNI topology view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Figure 4-3 View of individual switch in network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Figure 4-4 ATM Administrator drag-and-drop capability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Figure 4-5 ATM Administrator connected through NMS-specific ELAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Figure 4-6 Switches that ATM Administrator cannot reach through Ethernet. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
Figure 4-7 Ethernet connected ATM Administrator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
Figure 4-8 Routes that allow connectively between ATM and Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
Figure 4-9 Routes allow Switches 4 and 5 to be managed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
Figure 4-10 ATM Administrator Help Topic dialog box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11
Figure 5-1 Front panel of 6A000 switch module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

xii SmartSwitch 6A000 Installation and Setup Guide
List of Figures

SmartSwitch 6A000 Installation and Setup Guide xiii
List of Tables
LIST OF TABLES
Table 2-1 I/O module ID numbers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Table 2-2 SmartSwitch 6000 contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Table 4-1 Default accounts and passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Table 5-1 Front panel LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Table 5-2 Hardware Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Table 5-3 Physical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Table 5-4 ATM Port Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Table 5-5 Protocols Standards and Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
Table 5-6 Management Standards and Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
Table 5-7 RJ-45 to DB-9 Adapter (PC Serial Port Adapter). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4

xiv SmartSwitch 6A000 Installation and Setup Guide
List of Tables

SmartSwitch 6A000 Installation and Setup Guide 1-1
1 INTRODUCTION
Welcome to the SmartCell 6A000 Installation and Setup Manual. The SmartCell 6A000 ATM switch is a module that
fits into the SmartSwitch 6000 chassis. You can install as many as five SmartCell 6A000 switches into a SmartSwitch
6000 chassis (using the 6C305-3 power supply). Themodule is hot swap-able, meaning that you can install and remove
it without turning off or disconnecting the chassis.
This manual provides instructions for installing and setting up the SmartSwitch 6A000 ATM switch module.
This manual provides information about
•Unpacking and inspecting your switch module
•Installing your switch module in the SmartSwitch 6000 chassis
•Configuring your switch to be functional on your network
•Using the command line console
•Using the SmartSwitch ATM Administrator graphical network management software
•Obtaining customer support
This manual also provides detailed mechanical, electrical, and performance specifications for the SmartSwitch 6A000
ATM switch.
Note For additional information about using the SmartSwitch 6A000, see the
SmartSwitch ATM User Guide. For a complete explanation of all SmartSwitch
6A000 console commands, see the SmartSwitch ATM Switch Reference Manual.

1-2 SmartSwitch 6A000 Installation and Setup Guide
Introduction

SmartSwitch 6A000 Installation and Setup Guide 2-1
2 SWITCH INSTALLATION
This chapter explains how to inspect and install your SmartSwitch 6A000 ATM switch module.
2.1 UNPACKING THE SWITCH
Remove the accessory carton from the SmartSwitch 6A000 shipping box. Carefully remove the switch from its
packing material.
2.1.1 Accessory Carton Contents
Open the accessory carton and check that it contains the following items:
— 7-foot UTP cable, terminated on both ends with RJ-45 connectors
— RJ-45 to 9-pin female adapter (labeled PC)
— Console cabling instruction sheet
— CDROM containing the following:
-SmartSwitch 6A000 operating firmware
-SmartSwitch ATM switch documentation in Adobe Acrobat format
-SmartSwitch ATM Administrator software
-MIB files
-SmartSwitch 6A000 Release Notes
Note If any of these items are missing, contact Cabletron Global Support Center
immediately.
2.2 INSPECTING THE SWITCH
Depending on the configuration ordered, your switch lookssimilar to one of the units in the drawing in Figure 2-1. The
6A000-04, shown on the left, has four I/O modules. The 6A000-02, shown on the right, has two I/O modules; the
empty I/O module positions are covered by metal blanks.

2-2 SmartSwitch 6A000 Installation and Setup Guide
Inspecting the Switch Switch Installation
Figure 2-1 6A000-04 and 6A000-02 front panels
Inspect the switch and make certain that its configuration corresponds to what was ordered. Also, make certain that the
input/output modules (IOMs) are of the correct type and number (See Table 2-1).
Table 2-1 I/O module ID numbers
Face Plate Number Physical Specification
IOM-21-4 155 Mbps OC-3/STM-1, MMF/SC (4 port)
IOM-22-4 155 Mbps STS-3c/STM-1, UTP-5/RJ-45 (4port)
IOM-29-4-MIX 155 Mbps OC-3/STM-1, SMF-IR/SC (1port) MMF/SC (3 port)
IOM-29-4-IR 155 Mbps OC-3/STM-1, SMF-IR/SC (4 port)
NO SYNC DATA
NO SYNC DATA
1234
1234
IOM-21-4 IOM-22-4
ATM
FAIL
STATUS
POWER
RX ENET
TX ENET
S
Y
S
T
E
M
C
O
M
AC
NO SYNC DATA
NO SYNC DATA
1234
IOM-22-4
1234
IOM-21-4
BD
E
T
H
E
R
N
E
T
NO SYNC DATA
1234
IOM-22-4
ATM
FAIL
STATUS
POWER
RX ENET
TX ENET
S
Y
S
T
E
M
C
O
M
AC
NO SYNC DATA
1234
IOM-21-4
BD
E
T
H
E
R
N
E
T

SmartSwitch 6A000 Installation and Setup Guide 2-3
Switch Installation InstallingtheSwitch
Note All Single-Mode fiber connectors on IOMs are blue.
If the switch hardware configuration is incorrect, contact Cabletron Global Support Center immediately.
2.3 INSTALLING THE SWITCH
The SmartSwitch 6A000 is hot swappable, meaning that you can install and remove it without turning off or
unplugging the SmartSwitch 6000 chassis. You can install as many as five switch modules in each chassis (using the
6C205-3 power supply). In this configuration, the SmartSwitch 6A000 modules provide up to 75 user ports. Modules
should be connected with inter-module trunks if traffic must cross between modules. Table 2-2 shows the maximum
number of LAN and ATM switch modules that can be installed in a SmartSwitch 6000 chassis.
Note A single 6C205-1 power supply (the older version of the 6C205-3) can support
only two SmartSwitch 6A000s within a SmartSwitch 6000 chassis. Three
SmartSwitch 6A000s can reside within a SmartSwitch 6000 chassis that contains
two 6C205-1 power supplies.
Follow the instructions below to install the switch module into the chassis. Refer to Figure 2-2.
IOM-29-4-LR 155 Mbps OC-3/STS-1, SMF-LR/SC (4 port)
IOM-31-1 622 Mbps OC-12/STM-4, MMF/SC (1 port)
IOM-39-1 622 Mbps OC-12/STM-4, SMF-IR/SC (1 port)
IOM-39-1-LR 622 Mbps OC-12/STM-4, SMF-LR/SC (1 port)
IOM-67-4 45 Mbps DS-3, Coax/BNC (4 port)
IOM-77-4 34 Mbps E-3, Coax/BNC (4 port)
Table 2-2 SmartSwitch 6000 contents
Numberof6Exxxor6Hxxxmodulesinstalled012345
Numberof6A000modulesthatcanbeadded543210
Table 2-1 I/O module ID numbers (Continued)
Face Plate Number Physical Specification

2-4 SmartSwitch 6A000 Installation and Setup Guide
Installing the Switch Switch Installation
1. Remove the metal blank that covers one of the empty slots in the chassis.
2. Open the ejectors at the top and bottom of the switch module.
3. With the LEDs at the top, align the top and bottom of the SmartSwitch 6A000 with the tracks in the
slot.
4. Slide the switch into the chassis. The switch module obscures the view of the tracks at the bottom of
the chassis, so be sure to look at that area as you begin to slide the switch into the chassis.
5. Close the ejectors. The installation is complete.