Cadel nice User manual

©2014 CADEL srl | All rights reserved – tutti i diritti riservati
en PELLET STOVE
installation, use and maintenance manual
nl PELLETKACHEL
handleiding voor installatie, gebruik en onderhoud
nice - miriam - cristal - pretty - kriss - mary - tecna - evo

2NICE - MIRIAM - CRISTAL - PRETTY - KRISS - MARY - TECNA - EVO
EN
Summary
1 MANUAL SIMBOLOGY ......................................... 3
2 DEAR CUSTOMER ................................................. 3
3 CAUTIONS ............................................................ 3
4 WARRANTY CONDITIONS .................................... 3
5 SPARE PARTS......................................................... 4
6 WARNINGS FOR THE CORRECT DISPOSAL OF THE
PRODUCT ..................................................................... 4
7 PACKAGING AND HANDLING .......................... 5
7.1 PACKAGING ....................................................5
7.2 STOVE HANDLING............................................ 5
8 CHIMNEY FLUE ................................................... 5
8.1 INTRODUCTION ................................................5
8.2 CHIMNEY FLUE..................................................6
8.3 TECHNICAL FEATURES...................................... 6
8.4 HEIGHT-DEPRESSION ........................................ 7
8.5 MAINTENANCE.................................................7
8.6 CHIMNEY POT................................................... 8
8.7 CHIMNEY COMPONENTS ................................ 8
8.8 EXTERNAL AIR INLET.......................................... 9
8.9 CHIMNEY FLUE CONNECTION ........................ 9
8.10 EXAMPLES OF CORRECT INSTALLATION...... 10
9 FUEL ................................................................... 11
9.1 FUEL................................................................. 11
10 INSTALLATION ................................................... 12
10.1 INTRODUCTION .............................................12
10.2 OVERALL DIMENSIONS ................................. 12
10.3 GENERAL INSTALLATION............................... 13
10.4 SIDE PANEL ASSEMBLY.................................. 14
10.5 ELECTRIC CONNECTION .............................. 15
10.6 CONNECTION TO THE EXTERNAL THERMOSTAT.... 15
10.7 VENTILATION..................................................15
11 USE ..................................................................... 16
11.1 ATTENTION .....................................................16
11.2 INTRODUCTION .............................................16
11.3 CONTROL PANEL ......................................... 17
11.4 USER MENU ....................................................18
11.5 START UP .......................................................18
11.6 STOVE ADJUSTMENT ................................... 18
11.7 AIR REGULATOR ............................................19
11.8 FAILED IGNITION............................................19
11.9 POWER FAILURE ............................................19
11.10 TEMPERATURE SETTING ................................ 19
11.11 FUME TEMPERATURE .................................... 19
11.12 SWITCHING OFF........................................... 19
11.13 CLOCK SETTING...........................................20
11.14 DAILY PROGRAMMING ............................. 20
11.15 WEEK-END PROGRAMMING ...................... 20
11.16 WEEKLY PROGRAMMING ........................... 20
11.17 FIRE EXTINGUISHING IN CASE OF FIRE........ 21
11.18 PELLET SUPPLY .............................................. 21
11.19 REMOTE CONTROL (OPTIONAL) ................ 21
12 SAFETY SYSTEM ................................................. 22
12.1 INTRODUCTION .............................................22
12.2 ”BLACK OUT” ALARM ................................... 22
12.3 ”FUME PROBE” ALARM................................. 22
12.4 ”HOT FUME” ALARM ..................................... 22
12.5 ”FAN FAILURE” ALARM ................................. 22
12.6 ”FAILED IGNITION” ALARM...........................22
12.7 ”NO PELLET” ALARM..................................... 22
12.8 ”THERMAL SAFETY” ALARM .......................... 22
12.9 ”FAILURE DEPRESS” ALARM.......................... 23
13 MAINTEINANCE.................................................. 23
13.1 INTRODUCTION .............................................23
13.2
BURNING POT AND ASH TRAY CLEANING .... 23
13.3 HOPPER AND AUGER CLEANING .............. 24
13.4 FUME CHAMBER CLEANING ...................... 25
13.5 FUME CONDUIT CLEANING ........................ 25
13.6 FUME FAN CLEANING ................................. 25
13.7 FUME PASSAGES CLEANING ...................... 26
13.8 FUME PIPES ANNUAL CLEANING ............... 27
13.9 GENERAL CLEANING .................................. 27
13.10 CLEANING OF PAINTED METAL PANELS .... 27
13.11 CLEANING OF CERAMIC AND STONE PANELS .... 27
13.12 GASKET REPLACEMENT ............................. 27
13.13 GLASS CLEANING ...................................... 27
14 IN CASE OF ANOMALY .................................... 28
14.1 ALARMS ......................................................... 28
14.2 PROBLEM SOLVING ...................................... 30
15 TECHNICAL DATAS ........................................... 33
15.1 REPAIR INFORMATION .................................. 33
15.2 FEATURES .......................................................34

3
NICE - MIRIAM - CRISTAL - PRETTY - KRISS - MARY - TECNA - EVO
EN
1 MANUAL SIMBOLOGY
• The icons with the stylized gures indicates whom the subject dealt in the paragraph is addressed to (between
the User and/or the Authorized Technician and/or the Specialized Stove-repairer).
• WARNING symbols indicates an important note.
USER
AUTHORISED TECHNICIAN
(ONLY to interpret or the Stove-manufacturer or the Authorized
Technician of Technical Assistance Service approved by the Stove-
manufacturer)
SPECIALIZED STOVE-REPAIRER
CAUTION:
READ CAREFULLY THE NOTE
CAUTION:
DANGER OR IRREVERSIBLE DAMAGE POSSIBILITY
2 DEAR CUSTOMER
• Our products are designed and manufactured in compliance with standards EN 13240 for wood stoves,
EN 14785 for pellet stoves, EN 13229 for re places, EN 12815 for wood cooker stoves, C.P.R. 305/2011 for
manufacturing products, Re n.1935/2004 for materials and objects which are in contact with foods, Dir.
2006/95/CEE for low tension, Dir.2004/108/EC for Electromagnetic compatibility.
• Read carefully the instruction contained in this manual to obtain the best efciency.
• This instruction manual is an integral part of the product: make sure it is delivered with the appliance also in
case of sold to others. In case of loss please ask a copy to your local Technical Assistance Service.
• All local regulations, including those referring to national European standards, must be respected during
appliance installation.
In Italy biomass system installation below 35 kW must comply with MD 37/08. Every qualied
installer who own these requirements, has to issue the certicate of conformity for the
installed system (“system” means: stove + chimney + air inlet).
• According to (EU) No. 305/2011 regulation, the “ Declaration of Performance” is available online at the web
sites www.cadelsrl.com / www.free-point.it.
3 CAUTIONS
• All the pictures carried in this manual are only for indicative and explanatory purpose and could therefore
slightly differ from your appliance.
• The referring appliance is those you purchased.
• In case of doubts or difculties in the comprehension or for problems not described in this manual, please
promptly contact your distributor or installer.
• It is forbidden to modify the appliance without authorization.
4 WARRANTY CONDITIONS
The company guarantees the product, with the exception of elements subject to normal wear listed below, for
a period of 2 (two) years from the date of purchase attested by:
• a document to serve as proof of purchase (invoice and/or receipt) that shows the name of the vendor and
the date on which the purchase was made;
• forwarding of the completed certicate of guarantee within 8 days of purchase.

4NICE - MIRIAM - CRISTAL - PRETTY - KRISS - MARY - TECNA - EVO
EN
Furthermore, the product must be installed and started by specialised personnel who must, where provided,
issue a declaration of conformity of the plant and of the proper functioning of the product, for the warranty to
be valid and effective.
We recommend testing the product before completion with the relative nishes (claddings, painting of walls,
etc.).
Installations not meeting the current standards, improper use and lack of maintenance as expected by the
manufacturer, void the product warranty.
The guarantee is valid on the condition that the instructions and warnings contained in the use and maintenance
manual are observed, and therefore the product is used correctly.
The replacement of the entire system or the repair of one of its components does not extend the guarantee
period, and the original expiry date remains unchanged.
The guarantee covers the replacement or free repair of parts recognised as being faulty at source due to
manufacturing defects.
To benet from the guarantee, in the event of a fault, the customer must have the guarantee certicate and
present it with the proof of purchase document to the Technical Assistance Ofce.
The guarantee does not cover malfunctions and/or damage to the appliance that arise due to the following
causes:
• Damage caused during transportation or relocation.
• All parts that develop faults due to negligence or improper use, incorrect maintenance, installation that does
not comply with the manufacturer’s instructions (always refer to the installation and use manual provided with
the appliance).
• Incorrect dimensioning with regards to the use or faults in the installation or failure to adopt the necessary
devices to guarantee proper execution.
• Improper overheating of the equipment, use of fuels not conforming to the types and quantities indicated in
the instructions provided.
• Further damage caused by incorrect user interventions in an attempt to x the initial fault.
• Worsening of the damage due to the continued use of the equipment by the user, once the defect has been
noticed.
• In the presence of a boiler, any corrosions, incrustations or breaks caused by water ow, condensation,
hardness or acidity of the water, improperly performed descaling treatments, lack of water, mud or limescale
deposits.
• Inefciency of chimneys, ues or parts of the plant affecting the equipment.
• Damage caused by tampering with the appliance, atmospheric agents, natural disasters, vandalism,
electrical discharges, res, faults in the electric and/or hydraulic system.
Also excluded from this guarantee are:
• Parts subject to normal wear such as gaskets, glass, claddings and cast iron grids, painted, chrome-plated or
gilded parts, handles and electric cables, bulbs, indicator lights, knobs, all parts which can be removed from
the hearth.
• Variations in colour of the painted or ceramic/serpentine parts and craquelure ceramics as they are natural
characteristics of the material and product use.
• Masonry work.
• Plant parts (if present) not supplied by the manufacturer.
Any technical interventions on the product to eliminate the above-said defects and consequent damages must
be agreed upon with the Technical Assistance Centre, who reserves the right to accept the relative appointment
or not. However, said interventions will not be carried out under warranty but as technical assistance to be
granted at part of any eventual and specic agreed conditions and in accordance with the fee in force for the
work to be carried out.
The user will also be charged for any costs incurred to remedy the incorrect technical interventions, tampering
or damage to the appliance, not attributable to original faults.
Save for the legal or regulatory limits, the guarantee does not cover the containment of atmospheric and
acoustic pollution.
The company declines all liability for any damage which may be caused, directly or indirectly, to persons,
animals or objects as a consequence of non compliance with any prescription specied in the manual, especially
warnings regarding installation, use and maintenance of the appliance.
5 SPARE PARTS
For each repair or adjustment which should be necessary, please contact the dealer where you purchased your
stove or your nearest Technical Assistance Service, specifying:
• Appliance model
• Serial number
• Type of problem
Use only original spare parts which you can nd at our Technical Assistance Services.
6 WARNINGS FOR THE CORRECT DISPOSAL OF THE PRODUCT
The owner is the sole party responsible for demolishing and disposing of the product. This must be performed in
compliance with laws related to safety and environmental protection in force in his/her country.

5
NICE - MIRIAM - CRISTAL - PRETTY - KRISS - MARY - TECNA - EVO
EN
At the end of its working life, the product must not be disposed of as urban waste.
It must be taken to a special differentiated waste collection centre set up by the local authorities or to a retailer
that provides this service.
Separating and recycling prevents potential negative effects on the environment and health (often caused by
inappropriately disposing of product parts). It also allows materials to be recovered in order to obtain signicant
savings in energy and resources.
7 PACKAGING AND HANDLING
7.1 PACKAGING
• The packaging is made up of recyclable cardboard boxes according to RESY standards, recyclable
expanded polystyrene inserts and wooden pallets.
• All packaging materials can be re-used for a similar use or eventually discharged as waste assimilable to the
municipal solid ones, in accordance with current regulations.
• After having removed the packaging please assure you about the integrity of the product.
Packaging are not toys and could cause suffocation or strangulation and other health
hazards! People (childreen included) with reduced mobility, psycological deseases or
without experience and knowledge must be kept away from packaging. The stove is not a
toy, please see ATTENTION page 16.
7.2 STOVE HANDLING
Both whether the stove is packed or not it is necessary to observe the following instructions for handling and
transporting the stove from its sale point to its installation point and for any future movements:
• The stove must be handled with idoneous means paying attention to the existing safety regulations;
• do not turn the stove upside down and/or upset it on one side, but keep it in vertical position or as accorded
with the constructor instructions;
• if the stove is made up of ceramic, stone, glass or any particularly fragile material components, all must be
moved with the utmost care.
8 CHIMNEY FLUE
8.1 INTRODUCTION
This chapter about the Chimney Flue has been drawn up in cooperation with Assocosma (www.assocosma.org)
and is based on European Standards (EN 15287 - EN 13384 - EN 1856 - EN 1443 - UNI 10683:2012).
It provides instructions for a good and correct execution of the chimney ue but it does not absolutely replace
the current standards which the qualied manufacturer/installer should comply with.
Please check with your local authorities if exists any restrictive regulation which regards the
combustible air inlet, the fumes exhaust system, the chimney ue and the chimney pot.
The company declines any responsibility regarding the bad running of the stove if it is due to the use of a no
correctly dimensioned chimney ue which does not respect current regulations.

6NICE - MIRIAM - CRISTAL - PRETTY - KRISS - MARY - TECNA - EVO
EN
8.2 CHIMNEY FLUE
Fig. 1 - Chimney Flues
LEGEND Fig. 1 page 6
1Chimney ue with insulated stainless-steel
pipes
2Chimney ue on the existing chimney
3Inspection plug
4Inspection door
5≥ 3,5 mt
• The chimney ue or chimney is of great importance for the correct running of the heating appliance.
• It is fundamental that the chimney ue is perfectly built and always maintained with a perfect efciency.
• The chimney ue must be sole (see Fig. 1 page 6) with insulated stainless-steel pipes (1) or installed on the
existing chimney ue (2).
• Both this solutions must be endowed with an inspection plug (3) and/or an inspection door (4).
It is forbidden to connect more pellet stoves or any other heating appliance to the same
chimney ue.
8.3 TECHNICAL FEATURES
Fig. 2 - Inclined roof

7
NICE - MIRIAM - CRISTAL - PRETTY - KRISS - MARY - TECNA - EVO
EN
LEGEND Fig. 2 page 6
1Height over the ridge of the roof = 0,5 mt
2Roof inclination ≥ 10°
390°
4Measured distance at 90° from the roof surface = 1,3 mt
• The chimney ue must be sealed from fumes.
• It must have a vertical run without narrowing. It must be realized with fume and condensation resistant
materials with thermal insulation and able to last against usual mechanical stresses.
It must be insulated to avoid condensation and to reduce fume cooling effects.
• The stove must be spaced out from fuels or ammable materials with an air gap or with insulating materials.
Check the distance with the chimney manufacturer.
• The chimney entrance must be placed in the same room where the appliance is installed or otherwise in
the adjacent room and it must be provided with a solid and condensation collection chamber under the
entrance, accessible through the sealed metal gate.
• Auxiliary exhaust fans cannot be installed neither along the chimney nor on the chimney pot.
• The inner section of the chimney ue can be round (the best one) or square and the jointed sides must have
a minimum radius of 20 mm.
• The section dimension must be minimum Ø120 mm and maximum Ø180 mm.
• Made the efciency of the chimney ue overhauled by an expert stove-repairer and if necessary cover the
chimney ue with materials in compliance with current regulations.
• The ue system must be placed on the roof.
• The chimney ue must be provided CE in accordance with EN 1443 regulation. Please nd attached an
example of label:
Fig. 3 - Example of label
8.4 HEIGHT-DEPRESSION
The depression (draught) of a chimney ue depends also on its height. Check the depression with the values
provided at FEATURES page 34. Minimum height 3,5 meters.
8.5 MAINTENANCE
• The chimney ue must be cleaned, since the soot and unburnt oil deposits reduce its section so blocking the
draught. In great quantities they can are up.
• The fumes extraction pipes (fumes conduit + chimney ue + chimney pot) must always be cleaned, scrubbed
and checked by an expert stove-repairer, in compliance with current regulations, with the instructions of the
stove-manufacturer and the directives of your insurance company.
• In case of doubts, please follow the most restrictive regulations.
• Have your chimney ue and chimney pot checked and cleaned by an expert chimney sweep at least once
a week. The chimney sweep has to release a written declaration about the security of the system.
• Not cleaning compromise safety.

8NICE - MIRIAM - CRISTAL - PRETTY - KRISS - MARY - TECNA - EVO
EN
8.6 CHIMNEY POT
Fig. 4 - Anti-wind chimney pots
The chimney pot is important for the correct running of the heating appliance:
• We recommend using an anti-wind chimney pot, see Fig. 4 page 8.
• The hole width for fumes exhaust must be the double of the chimney ue width and tted in a way that the
fume exhaust is assured also in case of wind.
• It should prevent the inltration of rain, snow and animals.
• The outlet height in the atmosphere must be away from the reux area caused by the roof structure or by
obstacles laying nearby (see Fig. 2 page 6).
8.7 CHIMNEY COMPONENTS
Fig. 5 - Chimney components
LEGEND Fig. 5 page 8
1Chimney pot
2Fume outlet
3Chimney ue
4Termal insulation
5External wall
6Chimney union
7Fume pipe
8Heat generator
9Inspection door
10 T-union with inspection plug

9
NICE - MIRIAM - CRISTAL - PRETTY - KRISS - MARY - TECNA - EVO
EN
8.8 EXTERNAL AIR INLET
Fig. 6 - Direct air inow Fig. 7 - Indirect air inow
LEGEND Fig. 6 page 9|Fig. 7 page 9
1Room to ventilate
2Adjacent room
3External air inlet
4Cleft under the door
• The room must be endowed with an external air recycling for a good climate in your ambient.
• The air inow from outside to the inner occurs directly, through an opening on the external wall of the room
(see Fig. 6 page 9); otherwise it occurs indirectly by air suction from rooms adjacent to the one to ventilate
(see Fig. 7 page 9).
• Bedrooms, garages, and store of ammable materials are excluded.
• The air inlet should have a total net surface of 80 sqcm2: the aforesaid surface is to widen if inside the room
there are other activated appliances (for example: electric ventilators for foul air suction, cooker hoods, other
stoves, etc...) which depress the environment.
• At switched on appliance it is necessary to check that the pressure fall between the room and the outside
does not exceed 4,0 Pa value: if necessary widen the air inlet (EN 13384).
• The air inlet must be realized at a height close to the oor with an external grid against birds. In such a way it
cannot be obstructed by any object.
• In case of installation with sealed-chamber the air inlet is not necessary.
8.9 CHIMNEY FLUE CONNECTION
Your pellet stove works through a fume draught forced by a fan. It is obligatory to check that all pipes are
realized in compliance with the following regulation on material selection: EN 1856-1, EN 1856-2 e UNI/TS 11278.
All must be effected by specialized personnel or companies as provided by UNI 10683:2012.
• The connection between the appliance and the chimney ue should be short in order to favor the draught
and to avoid condensation in the pipes.
• The fume conduit should be equivalent or longer than the outlet joint ones (Ø 80 mm).
• Some stove models are endowed with a lateral and/or back exhaust. Check that the unused exhaust is
sealed with the plug given with standard equipment.
SYSTEM TYPE Ø80 mm PIPE Ø100 mm PIPE
Minimum vertical length 1,5 mt 2 mt
Maximum length (with 1 union) 6,5 mt 10 mt
Maximum length (with 3 unions) 4,5 mt 8 mt
Maximum number of unions 3 3
Level section (minimum inclination 3%) 2 mt 2 mt
Installation at a height above 1200 m a.s.l. NO Obligatory
• Use a plate pipe for stoves of Ø80 mm or Ø100 mm depending on the type of system and with silicone gaskets.
• It is forbidden to use metal, bre cement or aluminium exible pipes.
• For change of direction it is obligatory always to use a union (with angle > 90°) with inspection plug which
enables an easy periodic cleaning of the pipes.
• Please assure you that after the cleaning the inspection plugs are sealed with its efcient gasket.
• It is forbidden to connect more appliances to the same fume conduit.
• It is forbidden to convey in the same fume conduit exhausts from overhanging cooker hoods.
• It is forbidden to exhaust ue gases directly from the wall towards the outside and closed spaces also at open

10 NICE - MIRIAM - CRISTAL - PRETTY - KRISS - MARY - TECNA - EVO
EN
top.
• It is forbidden to connect any other appliance (wood stoves, cooker hoods, boilers, etc...).
• The fume conduit must be placed at a distance of minimum 500 mm from ammable or heat-susceptible
components.
8.10 EXAMPLES OF CORRECT INSTALLATION
Fig. 8 - Example 1
LEGEND Fig. 8 page 10
1Insulating material
2Reduction from Ø100 to Ø80 mm
3Inspection plug
4Minimum safety distance = 0,5 mt
• Chimney ue installation Ø120 mm with an enlarged drilling for pipe transit.
Fig. 9 - Example 2
LEGEND Fig. 9 page 10
1Insulating material
2Inspection plug
3Chimney inspection entrance
4Minimum safety distance = 0,5 mt
5Inclination ≥ 3°
6Level section ≤ 1 mt

11
NICE - MIRIAM - CRISTAL - PRETTY - KRISS - MARY - TECNA - EVO
EN
• Old chimney ue with an inserted pipe of minimum Ø120 mm and with an external door which enables the
chimney cleaning.
Fig. 10 - Example 3
LEGEND Fig. 10 page 11
1Insulating material
2Inspection plug
3Minimum safety distance = 0,5 mt
• External chimney ue entirely made up of insulated stainless steel pipes, i.e. with double wall of minimum Ø120
mm: all must be rmly attached to the wall. For chimney against wind effects please (see Fig. 4 page 8).
• Ducting system through T-unions which enables an easy cleaning without disassembling the pipes.
We recommend to check with your chimney ue manufacturer the safety distances which
must be respected and the type of insulating material. The aforesaid regulations are valid
also for holes made on the wall (EN 13501 - EN 13063 - EN 1856 - EN 1806 - EN 15827).
9 FUEL
9.1 FUEL
• The type of fuel to use is only the pellets.
• Use top-quality pellets because they have inuence in the caloric value and in ash remains.
• Pellets features are: dimension Ø6-7mm (D06 Class), maximum lenght 40 mm, caloric value 5kWh/kg, humidity
≤ 10%, ash remains ≤ 0,7%, they must be correctly pressed and not much mealy, without sizing agents, resins
and other additives (it is advisable to use pellets in compliance with the regulation EN14961-2 type ENplus-A1
).
• Not adequate pellets cause a bad combustion, a frequent burning pot obstruction and exhaust conduits
obstruction. Further it decreases the caloric value, soils the glass and increases consumptions and ash and
unburnt granules quantity.
Humid pellets cause a bad combustion and running, so please assure you that they are
stored in dry places and far at least one meter from the stove and/or any other source of
heat.
• It is advisable to try different type of pellets available on the market and to choose that which gives the best
performance.
• The use of bad quality pellets can damage the stove so that the warranty and manufacturer liability fall.
• Do not use the appliance as waste inceneretor.
• On all our product are used high-quality materials such as stainless-steel, steel, cast iron, etc... These materials,
before being sold on the market, are tested in laboratory, but despite this on the components which enable
the pellets ow (auger) there could exist minimum differences in the material used, in roughness and porosity,

12 NICE - MIRIAM - CRISTAL - PRETTY - KRISS - MARY - TECNA - EVO
EN
which could generate usual variations in fuel transportation (pellets), causing a ame raising or drapping with
a possible switching off at lower powers.
• Depending on the type of pellets it could be necessary a parameters adjustment, please contact an
Authorized Assistance Service.
10 INSTALLATION
10.1 INTRODUCTION
• The assembly position must be chosen depending on environment, outlet, chimney ue.
• Check with local authorities if there are any restrictive regulations which regard the combustible air inlet,
room ventilation, fume exhaust system together with chimney ue and chimney pot.
• The manufacturer declines any responsibility in case of installation which are not in compliance with current
regulations, in case of a wrong room ventilation system, in case of an electric connection which is not in
compliance with regulations and in case of a wrong use of the appliance.
• Intallation, electric connection, operation test and maintenance must be carried out by an authorized and
skilled technician.
• Check if there is the combustible air inlet.
• Check the probable presence of other stoves or appliances which could depress the room (see EXTERNAL
AIR INLET page 9).
• Check at switched on stove if there is the presence of CO in the room.
• Check if the chimney has the necessary draught.
• Check if during the fume passage all has been executed in safety (probable fume losses and distances from
ammable materials, etc.…).
• The installation of the appliance must enable an easy access for appliance, fume exhaust pipes and chimney
ue cleaning.
• The installation must enable en easy access to the electric connection plug (see ELECTRIC CONNECTION
page 15).
• It is forbidden to install the stove in bedrooms, bathrooms and in rooms used for storing combustible materials
and in one-room ats.
• The installation in one-room ats is allowed if they are in sealed chamber.
• In any case the stove must not be installed in rooms where it can get in touch with water or water splashes
because this can cause burn hazards and short-circuit.
• To install more appliances, the external air inlet must be correctly dimensioned (see EXTERNAL AIR INLET page
9).
10.2 OVERALL DIMENSIONS
Fig. 11 - General dimensions

13
NICE - MIRIAM - CRISTAL - PRETTY - KRISS - MARY - TECNA - EVO
EN
LEGEND Fig. 11 page 12
148,6 - 55 -57 cm
295 cm
346,6 - 47 cm
426,5 cm
517 cm
613,2 cm
7Exhaust fumes d.8 cm
8Hole combustion air inlet d.4 cm
10.3 GENERAL INSTALLATION
Fig. 12 - General installation
LEGEND Fig. 12 page 13
1Stove
2Minimum lateral distance = 300 mm
3Minimum rear distance = 200 mm
4Minimum front distance = 1000 mm
• Please check that the oor has an adequate load capacity. If the existing one does not satisfy this requirement,
appropriate measure should be provided (for example a plate for distributing the load).
• It is obligatory to install the stove away from walls and/or pieces of furniture, with a minimum air ow of 300
mm on the sides and 200 mm on the back, to enable an ecient appliance cooling and a good distribution
of heat in the room (see Fig. 12 page 13).
• For safety re regulations the distances from ammable or sensible to heat objects (sofas, pieces of furniture,
wooden covering, etc...) must be respected, has described in Fig. 12 page 13.
• If there are highly ammable objects (curtains, tted carpet, etc...), all these distances must be further
increased with 1 meter.
• If the walls are made up of ammable materials, check the safety distances (see Fig. 12 page 13).
• At maximum power check that the wall temperature does not ever exceed 80°C. If it would be necessary
please install a re resistant plate on the concerned walls.
• In some countries also masonring load-bearing walls are considered ammable.

14 NICE - MIRIAM - CRISTAL - PRETTY - KRISS - MARY - TECNA - EVO
EN
10.4 SIDE PANEL ASSEMBLY
Fig. 13 - Upper screws removal Fig. 14 - Backward screws removal
• Remove the top cover: unscrew the 2 upper screws and the 3 backward screws (see Fig. 13 page 14 and
Fig. 14 page 14).
Fig. 15 - Side panel insertion Fig. 16 - Ceramic panel insertion
• Insert from on high the metal side panels on the appropriate guides getting it slightly course all the way (see
Fig. 15 page 14).
• Insert from on high the ceramic side panels on the appropriate guides getting it slightly course all the way
(see Fig. 16 page 14).
Fig. 17 - Coloured side panel insertion
• The narrow side panel is to clasp on the squared holes (see Fig. 17 page 14).
• Recompose all.

15
NICE - MIRIAM - CRISTAL - PRETTY - KRISS - MARY - TECNA - EVO
EN
10.5 ELECTRIC CONNECTION
Warning: the appliance must be installed by an authorized technician!
• The electric connection occurs through a cable with plug put in an electric socket which is able to support
charge and tension specic of every model, as described in the technical datas table (see FEATURES page
34).
• The plug must be easily accessible when the appliance is installed.
The cable must not get in touch with the fume exhaust pipe and nor with every other part
of the stove.
• Please further assure you that your network is endowed with an efcient earth connection: if it does not exist
or if it is not efcient, please endow you with one in compliance with the law.
• Connect the supply cable rst on the back of the stove (see Fig. 18 page 15) and then at a wall electric
socket.
Fig. 18 - Electric socket with master switch
• The master switch O/I (see Fig. 18 page 15) is to open only to switch the stove on, otherwise it is advisable
to keep it off.
• Do not use extension cables.
• If the feeder cable is damaged, it must be replaced by an authorized technician.
• When the stove is not going to be used for a long period of time, it advisable to remove the plug from the
socket on the wall.
10.6 CONNECTION TO THE EXTERNAL THERMOSTAT
The stove works through a thermostat probe placed in its inner. If you desire, the stove can be connected to an
external room thermostat. This operation must be executed by an authorized technician.
• External thermostat: set up a temperature which is round 7°C.
• External chronothermostat: set up a temperature which is round 7°C and desable the chrono functions from
the menu 03-01.
10.7 VENTILATION
• The stove is endowed with a ventilation system.
• The air blown from fans keeps the appliance at a low temperature range in order to avoid high stresses to the
materials which make it up.
Fig. 19 - Do not cover air slits

16 NICE - MIRIAM - CRISTAL - PRETTY - KRISS - MARY - TECNA - EVO
EN
Do not cover the hot air outlet slits with any object to avoid stove’s overheating!
The stove is not suitable for food cooking.
11 USE
11.1 ATTENTION
This appliance must not be used by people (childreen included) with reduced mobility,
psycological deseases or without experience and knowledge except in case of supervision
or instruction about the use of the appliance by people responsible for their safety.
Childreen must be constantly overseen in order to assure that they do not play with the
appliance.
The stove is provided with a hand rejector: this rejector can be removed exclusively by the
stove manufacturer or by the Technical Assistance Service.
During its running, the stove reaches high temperatures: keep away childreen and animals
and for your safety please use appropriate reproof devices, such as heat-protecting gloves.
11.2 INTRODUCTION
To have the best performance with the lowest consumption please follow the here descripted instructions.
• The lightning of the pellets occurs very easily if the installation is correct and if the chimney ue is efcient.
• Switch on the stove at Power 1 for at least 2 hours in order to enable the materials which make up the boiler
and the replace to adjust the inner springing stress.
• Oily plant waste and lacquers can cause smells and smoke during the rst working hours: it is advisable to
ventilate the room because they could be noxious to people and animals.
• By using the stove the varnish inside the combustion chamber could be subjected to alterations. This
occurrence can be attributed to different reasons: an excessive stove overheating, the presence of chemical
agents in bad quality pellets, bad chimney draught, etc. Therefore varnish endurance in the combustion
chamber cannot be guarantee.
Set values from 1 to 5 are dened by the manufacturer and they can be changed only by
an authorized technician.
Do not use ammable liquids during the ignition (alcool, petrol, oil, etc...).

17
NICE - MIRIAM - CRISTAL - PRETTY - KRISS - MARY - TECNA - EVO
EN
11.3 CONTROL PANEL
PANEL ELEMENT DESCRIPTION
P1 and P2: when in set temperature mode, they are useful to increase or decrease the
thermostat value from min. 6°C to max 40°C. Keeping pressed P2 key it is possible to see
the fume temperature at the exhaust. Both have programming functions.
P3: it enables to enter set temperature and User and Technician parameters menu.
P4: switching on and off, alarm reset and exit from programming.
P5 and P6: increase and decrease the caloric power from 1 to 5.
Chrono: active time programming.
Ignition plug: active ignition.
Auger: active.
Fume fan: active.
Exchanger fan: active.
-
Alarm: active.
Fig. 20 - LCD control display
LEGEND Fig. 20 page 17
1Time
2Power
3State
4Message
5Temperature

18 NICE - MIRIAM - CRISTAL - PRETTY - KRISS - MARY - TECNA - EVO
EN
11.4 USER MENU
By once pressing P3 key you can hace access to user parameter controlling. To let them slide press P5 and P6
keys. They are:
POS. REFERENCE DESCRIPTION
1 SET CLOCK Set date and time. The board is provided with a lithium battery which enables a clock
autonomy of 3/5 years. See CLOCK SETTING page 20.
2 SET CHRONO
Press once P3: “CHRONO ENABLE” appears. Press P3 again and with P1 and P2 put in “OFF”
or “ON”. For daily, week-end or weekly programming, see DAILY PROGRAMMING page
20. CAUTION: do not active if STAND-BY function is active!
3SELECT
LANGUAGE Press once P3 key and with P1 and P2 keys select the desired language.
4 STAND-BY MODE
It activates a function which, if the set ambient temperature has been exceeded for more
then 10 minutes, start the switching off phase up. If the ambient temperature has fall at
more than 2°C, the stove will restart automatically up, starting from START UP page 18.
Press once P3 key and with P1 and P2 keys put in “OFF” or “ON”. CAUTION: do not activate
if CHRONO function is active!
5BUZZER MODE
(audio alarm) Press once P3 key and with P1 and P2 keys put in “OFF” or “ON”.
6 INITIAL LOAD When the stove has its rst ignition, the auger is completely empty. If it should be necessary
do a precharge by pressing P3 key, then P1 key for starting up and P4 key for stop.
7 STOVE STATE It shows all parameters connected to the stove state: this is a menu for the Authorized
Techinician
8 TECHNICA SETTING Only for the Authorized Technician.
9 SET FLAME It enables to set the ame dipending on the draught of the chimney ue.
11.5 START UP
We remind you that the rst ignition must be carried out by a specialized and authorixed technician who will
check that all is installed in compliance with current regulations and checks the efciency.
• If inside the combustion chamber there are booklets, manuals, etc..., remove them.
• Check if the door is correctly closed.
• Check if the stove is correctly inserted in the electric socket.
• Before switching the stove on, assure you the burning pot is clean.
• To start the stove up, keep pressed P4 key for an instant till it will be shown “START” and “PREHEATI WAIT”: the
preheating of the ingnition resistance starts. After 2 minutes about, it will be shown “PELLET LOAD, FLAME WAIT”,
in this phase the auger loads the pellet and the heating of the resistance continues. When the temperature is
sufciently high (after 7-10 minutes about), the ignition is considered as happened and on the display shows
“FIRE PRESENT”.
• Completed the phase “FIRE PRESENT”, the control unit enter the “WORK” phase showing the set caloric
power and ambient temperature. It is in this phase that P5 and P6 keys settle the stove power from 1 to 5. If
the value of the ambient temperature exceeds the limit set on the keyboard on the temperature setting, the
caloric power will be carried at the minimum showing “WORK, MODULATI”. When the ambient temperature
turns back below the set temperatur, the stove turns back to the set power.
11.6 STOVE ADJUSTMENT
The stove is adjusted according to the chimney ue and used pellets datas, as per technical characteristics (see
FEATURES page 34). If the datas do not correspond, the authorized technician can adjust the stove.
• If the pellet is small in size and with a greater caloric power, (for example: encrusted burning pot), the pellet
drop must be decreased from the menu “SET FLAME”, press P3 “PELLET TYPE”, press P3 again “PELLET LOAD”
and with P2 key decrease the pellet quantity from -1 (which is -2%) till -9 (which is -18%).
• If the chimney ue has a lower draught (for example: weak ame, sooty glass) the revolutions of the geared
motor must be increased from the menu “SET FLAME”, press P5 “CHIMNEY TYPE”, press P3 “FUME-FAN CHIMNEY”
and with P1 key increase the fume fan revolutions from +1 (which is +5%) till +9 (which is +30%).
• If the chimney ue has a greater draught (for example: because of pellets fall on the burning pot) decrease
the fume fan revolutions from -1 to -9.

19
NICE - MIRIAM - CRISTAL - PRETTY - KRISS - MARY - TECNA - EVO
EN
Pay attention if the value is positive or negative..
11.7 AIR REGULATOR
The stove is provided with a back air regulator and must have the following parameters (written also on the back
of the stove):
Fig. 21 - Air regulator
• Air regulator entrance 12 mm to nominal power with a chimney ue of 11 Pa.
11.8 FAILED IGNITION
If the pellets do not burn, the failed ignition will be indicated by the alarm “FAILED IGNITION”.
• If the room temperature is lower than 10°C, the plug is not able to bear the ignition stage. To support it please
insert some pellets in the burning pot and a piece of burning relighter igniter material on the pellets (for
example relighters cubes).
After a failed ignition the burning pot must be empty from the amassed pellets, before
starting the stove up again.
• Too much pellets in the burning pot, or humid pellet, or sooty burning pot make ignition difcult and create
dense white smoke which is harmful to health and can cause explosions on the combustion chamber. It is
therefore necessary not to stand in front of the stove during ignition stage if dense white smoke is present.
If after some months the ame appears weak and/or orange colored or the glass tends
to blackens and the burning pot to become encrusted, clean the stove, clean the fume
conduit and the chimney ue.
11.9 POWER FAILURE
• After a black-out lower than 5 seconds, the stove turns back to the power which was settled.
• After a black-out of more than 5 seconds, the stove enters the “COOLING WAIT” phase. Completed this
phase, it starts automatically up with the different phases (see START UP page 18).
11.10 TEMPERATURE SETTING
• To modify the ambient temperature it is sufcient to press P1 and P2 keys according to the desired temperature
inside the menu “SET TEMP AMBIENT”.
• To see the set temperature, press once P1 key.
11.11 FUME TEMPERATURE
To check the fume temperature at the exhaust it is sufcient to keep pressed P2 key.
11.12 SWITCHING OFF
To switch the stove off, keep pressed P4 key: the display shows “FINAL CLEANING”. After about 10 minutes, also
the fume fan switches off (this happens always, independently if the stove is hot or cold). Then “OFF” will be
shown.

20 NICE - MIRIAM - CRISTAL - PRETTY - KRISS - MARY - TECNA - EVO
EN
If the pellets are of bad quality (if contains sizing agents, oils, varnishes, plastic remains or if
it is mealy), deposits will form along pellets drop pipe during the running. When the stove is
switched off, these remains could form little hot coals that rising along the pipe could reach
the pellets on the hopper burning them and creating a thick and harmful smoke inside the
room. Please always keep the hopper closed with its own lid. If the pipe is sooty, please
clean it (see INTRODUCTION page 23).
11.13 CLOCK SETTING
• Press P3 key and then P5 key till underlining “SET CLOCK” menu (02).
• Press once P3 (DAY) and with P1 and P2 keys select the day of the week (Monday, Tuesday, Wednesday,
Thursday, Friday, Saturday, Sunday).
• Press for the second time P3 key (HOURS) and with P1 and P2 keys set the hour.
• Press for the third time P3 key (MINUTES) and with P1 and P2 keys select the minutes. Press for the fourth time
P3 key (DAY) and with P1 and P2 keys select the day of the month (1,2,3...29,30,31).
• Press for the fth time P3 key (MONTH) and with P1 and P2 keys select the month:
• Press for the sixth time P3 key (YEAR) and with P1 and P2 keys select the year.
• To exit from the programme press P4 twice.
11.14 DAILY PROGRAMMING
It allows to enable, disable and settle the daily chronothermostat functions.
Press P3 key and then P5 key till the menu “SET CHRONO”. Press once P3 key and with P5 and P6 keys select
the “PROGRAM DAY”. Press once P3 till nding “CHRONO DAY”. With P1 and P2 keys put in “OFF” or “ON”. It is
possible to set two working times delimited by the set times.
After “CHRONO DAY”:
• Press P5: the display shows “START 1”, with P1 and P2 keys set the ignition time value or put in “OFF”.
• Press P5: the display shows “STOP 1”, with P1 and P2 keys set the switching off time value or put in “OFF”.
• Press P5: the display shows “START 2”, with P1 and P2 keys set the ignition time value or put in “OFF”.
• Press P5: the display shows “STOP 2”, with P1 and P2 keys set the switching off time value or put in “OFF”.
• Press P4 key three times to exit from the menu.
11.15 WEEK-END PROGRAMMING
It allows to enable, disable and settle the chronothermostat functions during saturday and sunday.
Press P3 key and then P5 key till the menu “SET CHRONO”. Press once P3 key and with P5 and P6 keys select
“PROGRAM WEEK-END”. Press once P3 till nding “CHRONO WEEK-END”. With P1 and P2 keys put in “OFF” or
“ON”.
It is possible to set two working times delimited by the set times and valid only for saturday and sunday.
After “CHRONO WEEK-END”:
• Press P5: the display shows “START 1 WEEK-END”, with P1 and P2 keys set the ignition time value or put in “OFF”.
• Press P5: the display shows “STOP 1 WEEK-END”, with P1 and P2 keys set the switching off time value or put in
“OFF”.
• Press P5: the display shows “START 2 WEEK-END”, with P1 and P2 keys set the ignition time value or put in “OFF”.
• Press P5: the display shows “STOP 2 WEEK-END”, with P1 and P2 keys set the switching off time value or put in
“OFF”.
• Press P4 key three times to exit from the menu.
11.16 WEEKLY PROGRAMMING
It allows to enable, disable and settle the weekly hermostat functions (saturday and sunday included).
Press P3 key and then P5 key till the menu “SET CHRONO”. Press once P3 key and with P5 and P6 keys select
“PROGRAM WEEK”. Press once P3 till nding “WEEKLY CHRONO”. With P1 and P2 keys put in “OFF” or “ON”. It is
possible to set four working times delimited by the set times.
After “WEEKLY CHRONO”:
Press P5: the display shows “START PROG-1”, with P1 and P2 keys insert the ignition time value or put in “OFF”.
Press P5: the display shows “STOP PROG-1”, with P1 and P2 insert the switching off value or put in “OFF”.
• Press P5: the display shows “MONDAY PROG-1”, with P1 and P2 keys set “ON” or “OFF”.
• Press P5: the display shows “TUESDAY PROG-1”, with P1 and P2 keys set “ON” or “OFF”.
• Press P5: the display shows “WEDNESDA PROG-1”, with P1 and P2 keys set “ON” or “OFF””.
• Press P5: the display shows “THURSDAY PROG-1”, with P1 and P2 keys set “ON” or “OFF”.
• Press P5: the display shows “FRIDAY PROG-1”, with P1 and P2 keys set “ON” or “OFF”.
• Press P5: the display shows “SATURDAY PROG-1”, with P1 and P2 keys set “ON” or “OFF””.
• Press P5: the display shows “SUNDAY PROG-1”, with P1 and P2 keys set “ON” or “OFF”.
• Now press P5 and repeat all the previous instructions for Prog-2, Prog-3, Prog-4.
• To exit press three times P4.