Calimet CM-5-ACFP User manual




1


www.bestirongatemotor.com
9949HaywardWaySouthElMonteCA91733
Tel:(626)4529009



1


www.bestirongatemotor.com
9949HaywardWaySouthElMonteCA91733
Tel:(626)4529009
16
Calimet Co Inc
9949 Hayward Way
South El Monte, CA 91733
Tel: [phone]
Alternate: 626-482-3066
Fax: [phone]
[email protected]om
www.bestirongatemotor.com
9949 Hayward Way, South El Monte, CA 91733
www.bestirongatemotor.com

1



2

PRODUCT SPECS：
VoltageInput：110V
Maximumoutputcurrent：15AM,Fuse:AC110V15AM
Remotecontroldistance：Openspace>150Feet(50meters)
MaximumGateweight:1000LBS
MaximumGatelength:22FEET







WARNING
ToreducetheriskofINJURYorDEATH:

Neverletchildrenoperateorplaywithgatecontroloraroundgate,keep
remotecontrolawayfromchildren.
ALWAYSkeeppeopleandobjectsawayfromgate.NOONESHOULDCROSS
THEPATHOFMOVINGGATE.
Testgateoperatormonthly.ThegateMUSTreverseincontactwitharigid
objectofreversewhen anobjectactivatesthe noncontactsensors.After
adjustingtheforceorlimitoftravel,resetgateoperator.Failuretoadjust
and reset the gate operator properly can increase the risk of INJURY or
DEATH.
UsetheemergencyreleaseONLYwhengateisnotmoving.
KEEPGATEPROPERLYMAINTAINED.Readowner’smanual.Haveacertified
servicepersontomakerepairsorinstalloperatorhardware.
The entrance is for vehicles ONLY. Pedestrians MUST use separate
entrance. 
SAVETHESEINSTRUCTIONS.

3000
50

2



3
Installation of Base

1. Layoutpositionof6Anchorsbymeasuringclearancebetweenanchorsand
insideedgeofgate.Figure1
2.  Installundergroundconduitsinareaforconduits.Figure2



Figure1      Figure2




3
Installation of Base
1. Lay out position of 4 Anchors by measuring clearance between
anchors and inside edge of gate. Figure 1
2. Install underground conduits in area for conduits. Figure 2

3



4
Installation Barrier distance

Figure3



Figure4

4



5
Position Of Gate and Operator
Twooptionsforchainconnections:


Figure5 RearMount

Figure6  FrontMount

5



6
Welding Bracket of Chain











Figure 7
Correct connection of chain
Figure 8
Figure 8. Follow the correct way to install chain. Incorrect installation will cause
malfunctionofoperatorandpotentialdamages.   

6



7
Power Connection




















Figure9



1. MUSTuseULprovedpowerwires,powerwiresMUSThaveminimumcapacity
for25Amcurrent. 
2. AlloperatorsMUSTbeproperlygroundedinordertopreventelectricalcharge.
Mustusededicatedcircuitforpowersupply. 
3. Whenpowerisconnected,turnoperatorpowerswitchtoONposition.





7



8
EMERGENCY RELEASE


Figure10


A.  EmergencyReleaseofgate
1.  Disconnectpower.
2.  PushReleasepedaldownwardandmoveslightlytotherightuntilitwaslocked
in.
3.  Holdandpushgatetodesireddirection.   


B.   Resetpedal(OnlywhenoperatorhasNoreactionwhileusingremotecontrol)  
1. Push pedal downward from locked position and slightly move to the left,
unlockedpedal.
2. AllowPedalriseuptoresetpositionandreleasepedal.



8
EMERGENCY RELEASE
Figure 10
A. Emergency Release of gate
1. Disconnect power
2. Push Release pedal downward and move slightly to the right until it was locked in down
position.

8



9
Entrapment Protection
Safety and Exit Loop




Figure11

9



10
Control Board Lay Out
Figure12