Calitop Calispace Ocean 80 User manual

Calispace Ocean 80 – assembly instructions
Preparation:
Lay out a sufficiently large area with cardboard (the telescopic rails are greased).
Place the components as shown in the picture.
Tools:
•Angle screwdriver, hexagon, 4 mm (Allen wrench, KEA key)
•Slot and Phillips screwdrivers
•Wrench (10 pieces)
•folding rule
1
1
2
1
2
2
3
45
67
8
9
10
11

Components basic version
Frame:
1 schmales Systemprofil (Querverbindung hinten) 1
2 Teleskopschienen mit vormontierten Winkeln (1x mit Federbolzen) 2
4 Befestigungsschrauben für Bodenschiene 3
Drawer:
2 schmale Systemprofile mit montierter Schubladenschiene 4
2 schmale, lange Systemprofile (1 x mit Griffschlaufe) 5
2 kleine Winkel 6
2 Senkkopfschrauben M5 x 10 7
2 Senkkopfschrauben M5 x 12 mit Vierkantmuttern 8
2 Endkappen schwarz 9
4 Verbindungswinkel für Schublade 10
4 Befestigungsflansche für Schublade 11

Drawer:
The drawer consists of two short system profiles with mounted drawer slide rails and two long
system profiles (one with handle loop).
Note:
Do not tilt profiles and connection angles
No violence, it is only with feeling!
Slightly loosen the screws of the connection bracket
The upper edge of the picture is seen in the direction of travel in front
Mounting steps:
•Arrange components
•nsert the mounting flanges (14) before connecting (about 20 cm distance from the
outside)
•nsert connecting caps (15) (pre-assembled).
•nsert connecting bracket (13) and tighten screws.
•Fix small angles (11) with countersunk screw M5 x 10 on left and right
•nsert end caps (16).

nstallation of the rear extension
There are two ways to attach the telescopic rails to the floor rails:
nstallation variant A:
•Attach telescopic rails to the rear system profile (2) with countersunk screw (8) M5x12
and square nut. The angles are flush with the profile.
•nsert the drawer into the telescopic rails. (The ball cages should be pushed all the way
back (towards the drawer).
•Lift the rear extension on the right so that the left holders go under the cabinet profile.
•Lower, and attach to the ground screws.
•Place washer and tighten with M6 nut.
Note:
The ground screws can be moved to the left and right if the holes are not exactly above the
ground screws.
nsert rear drawer.(Film)
The film shows the older version with column profile(x2) and center profile (x1).
nstallation variant B:
nstall the left and right telescopic rails individually. f the ground screws do not fit exactly
through the holes, the ground screws can be moved to the right or left. Then screw the rear
floor profile to the angles.
Then insert the drawer as described above.
x1
x2

General installation instructions:
The drawer is unlocked on the
sides (left and right opposite)
and can therefore be pulled out
completely.
The rear seat must be about
3-4 cm are advanced.
nserting the fixing screws
(Film).
*
*
The nut bolt must be screwed hand-tight and the knurled nut screwed approx. 1 cm. The screw
is then countersunk in the rail and placed in the left-hand position and pulled upwards. Then
the knurled nut is screwed down by hand. Now the bolt can be screwed in to the right until it is
fixed. Finally, the knurled nut is unscrewed.
The floor screws must be installed at the same distance on the left and right.
The distance from the back is about 3,8 cm.
After approx. 500 km, all screw connections should be tightened.
Also, the balls should be occasionally greased.