Campania International Newport FT-0124 User manual

F
T
-
0124 Newport
Fountain
Professional installationisrecommendedfor thisfountain!Assemble your fountainonalevel surface usingcrushedstone, gravel, or
cementpadasthebase.
R
evised
April 23, 2018
-WINTERCARE-
Fountainbowls/topsandotherfountaincomponents,whichcollect water, shouldnotbeleftoutsideinthewinter since anycomponent,
whichfillswithwater andfreezesmaycrack.Likewisecomponentssuchaspedestals,whichremaininabasin,filledwithwater,
whichthenfreezes,mayalsocrackor crumble. Ideally, therefore, afountainshouldalwaysbestoredindoorsor inadryprotected
place suchasacoveredporchawayfromtheelements. However, ifafountainmustbeleftoutside:
(1) Removepump, rubber stoppers, drainpipes, finials,andother smallcomponentsfor storageindoors. Note that stoppersor
drainpipesareremovedtoallowdrainageintheeventwater accumulatesinanybasin.
(2) Raisefountainbasefromgroundwithwood stripssothat basewill notfreeze tothegroundsurface.
(3) Cover or wrapthefountainwithburlapor other absorbentmaterial (oldblanket or towel) andthencover securelywith
plastic,making surethat water will notaccumulate inthebasinor other fountaincomponentandfreeze;
(4) Checkfountainperiodicallytoinsurethat plastic issecureandwater isnotaccumulating inanyfountaincomponent.
-GENERALFOUNTAINTIPS-
Install fountainsonalevel surface. Youwill needaproperlygrounded110-volt (AConly) GFCI protectedreceptaclenear the
fountainfor your pump. All pumpsaresubmersible andmustbecompletelyunderwater tofunctionproperly. Testall pumpsand
adjusttofull outputprior toassembly. Itisnotrecommendedthat fountainsbeplaceddirectlyongrass or dirt. Positionthechannel
opening at thebaseofeachfountaintoward theelectrical outlet tobeusedsince thepump
cord willbethreadedthroughthisopening.
CheckoutYouTubefor a“Howto”video. (https://youtu.be/O1AadJ99W24)
For moreCampania product informationvisit www.campaniainternational.com
All of ourcaststone is proudly
Pump KitPartsList
PK800 pump(2)
#10 stopper withdoublehole (1)
#7 DrainStopper (1)
Metal plug for hole inside of basin(alreadyinstalledin basin) (1)
2.8oztube ofsilicone(1)
3” lengthof 3/4” Clear Vinyltubing (2) **
3” lengthof 5/8” Clear Vinyltubing (2) **
Approx. 60” lengthof 1/2” BlackNon-Kinktubing (2)**
Approx. 15” lengthof 1/2” BlackNon-Kinktubing (1)
9” lengthof 1½” PVC “Stand Pipe” (1)
Rubber band (1)
Wedges(22)
Hoseclamps(5) *
WoodSpacersfor installation(8)
*Hoseclamps maybeusedasflowrestrictors
**Tubing is preassembled
FOUNTAININFORMATION:
Thisfountain holdsapproximately240 gallonsof water.
Thisfountain usesamediumfountain cover but does
not cover the basin.
(FTNCOV-MED)
Compatible withRefill #10 Device and LEDkit
(A different style stopper mayberequestedfor therefillkit.)
TOOLSREQUIRED:
Bubble Level
Tape Measure
PUMPINFORMATION:
OEMPP800 - 800GPH Pump
16 FTcord length

F
T
-
0124 Newport
Fountain
Professional installationisrecommendedfor thisfountain!Assemble your fountainonalevel surface usingcrushedstone, gravel, or
cementpadasthebase.
R
evised
April 23, 2018
FGB-2020(260lbs)
90”Wx10”H
FT-239J(242lbs)
20”Lx20”Wx12”H
FT-114H(150lbs)
15.5” Lx15.5”Wx18”H
FT-124F(327lbs)
47”Wx6.5”H
FT-305C (52lbs)
12.5”Wx16.25”H
FT-114D(116lbs)
32”Wx9.5”H
1. Place thefiberglass basinwhere thefountain is to beinstalled.
a.Besure to checkthateachpart is leveland centeredduring theassembly of
this fountain.
2. Spread athin amountofsiliconeon both pump cords approximately3 feetfromthe
pumps and fit theminto thedoubleholed stopper.
3. Feed thepump cords through theholein thebasin.
4. To ensure alevelinstallation, makesure thatyou run theremainingcord through the
channelin thebottomofthebasin.
5. Press stopper firmlyand evenlyinto theholeofbasin.
6. Spread athin bead ofsiliconearound theperimeterofthestopper, slit in thestopper,
and around thepump cords.
7. Looselywrapcords up inthecenter ofthebasin.
8. Place thefountain base(FT-239J)over thepumpsand thecords.
9. Place thelargepedestal(FT-114H)on top ofthebase.
10. Place thelargebowl(FT-124F)on top ofthelargepedestal.
11. Place thestandpipeinsidetheholeofthelargebowl.
12. Insertboth 60”lengths of½”non-kink tubingthrough thepipeonto thebottomofthe
base. Makesure to feed theend with theassembled clear vinyltubingdown into the
basin.
13. Connecttheclearvinyltubingonto thepump water outlets ofthepumps.
14. Fold theend ofoneofthelengths oftubingdownover theedgeofthestandpipe.
15. Secure thetubingbyplacingtherubber band over thetubingand pipeso thatthe
tubingopeningpoints down into thebowl.
16. Inserttheremainingtubingcomingoutofthestandpipeup through thepedestal(FT-
305C)and place thepedestalover thestandpipeinthecenter ofthelargebowl.
17. Place ahoseclamp over thetop end ofthetubingand connectthatend ofthetubingto
thebottomofthemiddlebowl(FT-114D). Tighten thehoseclamp to ensureagood
seal.
18. Place themiddlebowldown onto themiddlepedestal.
19. Place ahoseclamp over oneend ofthe15”lengthof½”non-kink tubing.
20. Connectthatend ofthetubingto thepipeprotrudingoutfromthetop ofthemiddle
bowl(FT-114D). Tighten thehoseclamp to ensureagood seal.

F
T
-
0124 Newport
Fountain
Professional installationisrecommendedfor thisfountain!Assemble your fountainonalevel surface usingcrushedstone, gravel, or
cementpadasthebase.
R
evised
April 23, 2018
FT-114C (39lbs)
13”Wx14.5”H
FT-114B (27lbs)
18.25”Wx5.25”H
FT-114A(11lbs)
5.5”Wx11”H
FT-114F(3lbs)
5.25”Lx2”Wx4”H
FT-239L(8lbs)
8.25”Lx1.75”Wx6.5”H
FT-124K(282lbseach)
38”Lx9”Wx15”H
21. Feed theother end ofthetubingup through thesmall pedestal(FT-114C)while
loweringthepedestaldown into themiddlebowl. Ensure thepedestalis leveland
centered in themiddlebowl.
22. Place ahoseclamp over theother end ofthe15”length of1/2”non-kink tubing.
23. Connectthatend ofthetubingto thebottomofthesmall bowl(FT-114B).Tighten the
hoseclamp to ensure agood seal.
24. Place thesmall bowlon top ofthesmall pedestal.
25. Place thefinial(FT-114A) in thesmall bowlbyloweringtheholeoverthecopper pipe
protrudingfromthebowl.
26. Cover themiddlepedestalpump access with thepump cover door(FT-114F).
27. Cover thepump access in thebottombasewith thepump cover door(FT-124J).
28. Place 1 pieceofcoping(FT-124K)directlyagainstthefiberglass basin (FGB-2020).
29. Place 1 wood spacer againstthebottomouter edgeofthefirstpieceofcoping.
a. Leaveabout1inchofthespacer sticking outfor easyremoval.
30. Position thesecond copingagainstthewood spacer and basin.
31. Repeatsteps 29 and 30 until only1 piece ofcopingis notin place. There should bea
gap between copings where theinsidecorners meet.
32. Insert1 plasticwedgeabout3 inches fromeach edgeofthe7 copings alreadyinstalled.
(This reduces thegap in theinner circleofthecoping.)
33. Carefullypush thefinalpiece ofcopinginto place and place the2 wedges under
a. Adjusttheother copingsasneededtoformacircle.
34. Removethewood spacers.
35. Fill thebasin with water.