Camplux FMGG302B User manual
Model: FMGG302B
PROPANE GAS GRILL GRIDDLE
Instruction For Installation And Use
Visit Us: Camplux.com
3330-A Marathon Ct Charleston, SC 29418 1(844) 538-7475
If you smell gas:
● Disconnect the gas supply to the barbecue.
● Extinguish all open flames.
● Open the lid on the grill griddle unit.
● If the smell persists, move away from the
barbecue and contact your gas supplier or the fire
brigade.
DANGER
● Do not store petrol or other flammable liquids or
gases near your barbecue or other electrical
appliances.
● Never keep an unused gas cylinder in the vicinity
of your barbecue or other electrical appliances.
WARNING
Read this instruction carefully and ensure that your appliance is properly installed, assembled, maintained and
serviced in accordance to these instructions. If you have any questions concerning the assembly or operation of
this appliance, please consult Camplux. Do not try to fix theproblems yourself, or it will cause injury or property
damage.
Precautions
● This gas grill griddle is intended for personal private use only.
● Accessible parts may be very hot. Please keep young children away.
● Do not move the appliance during use.
● Turn off the gas supply at the gas cylinder after use.
● Do not modify the appliance.
● Any modification of the appliance may be dangerous.
Improper Use:
Any other use, or any use beyond the stated purpose, is not permissible. This appliance in particular to the
following types of misuse:
● Do not operate the grill griddle with coal or fuel other than liquid gas
(propane/butane).
● Do not operate the grill griddle as a heater.
● Do not use the grill griddle to heat materials and substances other than
barbecue food.
IMPORTANT! Read thoroughly before use. Keep these operating instructions for future reference.
NOTE: for the installer: This manual must remain with the consumer.
Pictograms & Signal Words
The following rules are used in these instructions to point out hazards and important information.
WARNING
Visit Us: Camplux.com
3330-A Marathon Ct Charleston, SC 29418 1(844) 538-7475
1
www.camplux.com
Safety Information:
Indicates a possible danger that can result in severe
personal injury or damage to property if the stated
measures are not taken
Indicates a hazardous situation which, if not avoided,
could result in death, serious injury or material damage
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury or material damage
Pictogram and signal word Note on
DANGER!
WARNING!
CAUTION!
Important Safety Precautions
CAUTION! Failure to obtain the following basic safety precautions may result in serious personal injury or
material damage due to fire or explosion.
Installation and assembly
CAUTION! Before you start, read the operating manual carefully.
WARNING! Never use the grill griddle if there is any visible damage. Never make any technical modifications
to the grill griddle. Only use original spare parts.
DANGER! Never install this grill griddle in an integrated or slide-in construction. This grill griddle is not suitable
for installation in caravans or boats.
Operation and use
WARNING! Use the product exclusively for the intended purpose.
DANGER! Only use the grill griddle in a well-ventilated spot and above ground level (i.e. not in areas
below ground level). Do not use the grill griddle in garages, covered passageways, tents, awnings, and other
closed areas or combustible structures.
DANGER! Fire or smoldering fire if flammable materials or substances are near the grill griddle. Choose
an area for installation where no flammable materials or substances are or will be, in close proximity to the
product. Minimum distance to flammable materials or substances: 6.6 ft overhead and 3.3 ft to the side.
Distance to flame-resistant materials, e.g. house walls: at least 1.9 ft.
CAUTION! Accessible parts can become very hot. Keep children away. Wear grill griddle mittens while
using .
WARNING! The grill griddle must stand level during operation and must not be moved.
WARNING! Never leave the grill griddle unattended when in use. Take particular care to ensure that
children and individuals with physical or mental disabilities are kept away from the barbecue. They may not be
able to identify the dangers correctly.
DANGER! Gas is highly flammable. When connecting the gas cylinder make sure that there are no
sources of ignition within a 16.4 ft radius. Protect the gas cylinder and the gas hose from direct sunlight and
other sources of heat (max. 122°F). Take particular care to ensure that the gas hose does not touch any part of
the hot barbecue.
2
www.camplux.com
Visit Us: Camplux.com
3330-A Marathon Ct Charleston, SC 29418 1(844) 538-7475
● Do not store petrol or other flammable liquids or gases
near your barbecue or other electrical appliances.
● Never keep an unused gas cylinder in the vicinity of
your barbecue or other electrical appliances.
● Never use the grill griddle if there is any visible
damage. Never make any technical modifications to
the grill griddle.
● Only use original spare parts.
● Use the product exclusively for the intended purpose.
● The grill griddle must stand level during operation and
must not be moved.
● Never leave the grill griddle unattended when in use.
Take particular care to ensure that children and
individuals with physical or mental disabilities are kept
away from the barbecue. They may not be able to
identify the dangers correctly.
● Do not close any openings on the sides or on the back
of the unit. Storage and/or non-use.
● Close the valve on the gas cylinder (b) immediately
when you finish using the grill griddle.
● If you will not be using the product for a longer period
of time, disconnect the gas cylinder and store them
properly:
● Protect the gas cylinder with a protective cap.
● The gas cylinder must be kept outdoors and out of the
reach of children.
● Gas cylinder must not be stored below ground level, in
garages, in stairwells corridors or other closed rooms.
WARNING
● Failure to obtain the following basic safety
precau-tions may result in serious personal
injury ormaterial damage due to fire or
explosion. Beforeyou start, read the
operating manual carefully.
● Accessible parts can become very hot.
Keep children away. Wear grill griddle
mittens while using.
● Clean the grease tray and cooking grate
regularly to avoid deposits that could lead
to a grease fire.
CAUTION
DANGER! Before each use check to ensure that all of the connections through which gas is supplied are
sealed and intact. The grill griddle must not be used if the connections for the gas supply are porous or faulty.
This also applies, for example, to hoses or fittings that are blocked with insects, as this can result in a
dangerous flashback.
DANGER! When igniting the gas flame, do not bend over the barbecue surface as deflagration can occur
if the gas has accumulated in the combustion chamber.
CAUTION! Clean the grease tray and cooking grate regularly to avoid deposits that could lead to a grease
fire.
WARNING! Do not close any openings on the sides or on the back of the unit. Storage and/or non-use.
WARNING! Close the valve on the gas cylinder (b) immediately when you finish using the grill griddle.
WARNING! If you will not be using the product for a longer period of time, disconnect the gas cylinder and
store them properly:
● Protect the gas cylinder with a protective cap.
● The gas cylinder must be kept outdoors and out of the reach of children.
● Gas cylinder must not be stored below ground level, in garages, in stairwells, corridors or other closed
rooms.
3
Visit Us: Camplux.com
3330-A Marathon Ct Charleston, SC 29418 1(844) 538-7475
www.camplux.com
● Never use a dented or rusty liquid gas cylinder.
● Never use a gas cylinder with a damaged valve.
● Never place a gas cylinder on its side, always install, transport and store the gas cylinder in a stable, upright
position.
● Never expose a gas cylinder to extreme heat or direct sunlight.
WARNING
Important information about gas & gas connections
liquid gas (lpg) propane, butane and mixtures that remain liquid at room temperature and low compression (< 10
bar). If the gas cylinder is opened, the pressure escapes and the liquid expands to the gaseous state.
Instructions for safely handling a gas cylinder:
● An empty liquid gas cylinder must not be stored directly next to a gas barbecue that is being used. Even
apparently empty liquid gas cylinders can still contain liquid gas and must, therefore, be treated with the same
care as a full liquid gas cylinder.
● When connecting and changing the gas cylinder, make sure that you do this only in rooms that are sufficiently
ventilated or outdoors. Make sure that there are no open fires or other sources of ignition, as well as other
persons in the vicinity.
Requirements for a liquid gas cylinder:
Only use liquid gas cylinders that comply with national regulations. Use liquid gas cylinders with the maximum
dimensions as specified in the installation instructions for your product.
If placed on the floor, the liquid gas cylinder may only be positioned at the side or rear of the barbecue. In this case,
make sure that the ground is firm and level.
Requirements for the gas pressure regulator:
The gas pressure regulator ensures that the gas grill griddle is always supplied with uniform gas pressure.
Only use the gas pressure regulator supplied with your grill griddle. If your product was delivered without a gas
pressure regulator (country-dependent), procure a gas pressure regulator that complies with your national
regulations.
Requirements for the hose line:
The hose line forms the connection between the liquid gas bottle and the gas barbecue.
The tested and CSA-Certified hose line must not be longer than 4.9 ft. Before each use, check whether the hose
line has any cracks or is wom.
● Make sure that the hose line does not have any kinks.
● Make sure that the hose line does not touch any hot surfaces.
Only use the hose line supplied with your gas barbecue. If your gas barbecue was delivered without a hose line
(country-dependent), procure a hose line that complies with your national regulations.
4
www.camplux.com
Visit Us: Camplux.com
3330-A Marathon Ct Charleston, SC 29418 1(844) 538-7475
What's In The Box
17
16
15
14
13
12
11
11
19
10
9
8
18
9
76
6
5
5
4321
No.
1
2
3
4
5
6
7
8
9
10
Name
Attachment Strap
Cover Cloth
Bottom-right Leg Unit
Base
Wheel Lid
Wheel
Axle
Bottom-left Leg Unit
Upright Leg Unit
Grease Cup
Qty
1
1
2
1
2
2
1
2
4
1
No.
11
12
13
14
15
16
17
18
19
Name
Side Table
Body
Flame Spliter
Cooking Grill
Griddle Plate
Upper Lid
Upper Lid Handle
Gas Support Stand
5/8"-18 UNF Gas Regulator
Qty
2
1
2
1
1
1
1
2
1
5
Visit Us: Camplux.com
3330-A Marathon Ct Charleston, SC 29418 1(844) 538-7475
www.camplux.com
Assembly Instructions
1. Connect the BASE(4) with the Leg Unit(8)(3).
Using M5 screw(A) to connect and lock the BASE(4)
with the Bottom-Left Leg Unit(8) and the
Bottom-Right Leg Unit(3).
2. Wheel installation.
Slide the Axle(7) through the holes located at the
bottom left, and then install the Wheels(6) at both
sides of the Axle(7). Lock them with R-Pin(D), and
then separately slide in the Wheel Lid(5).
Parts Board
A. Flange screw M5x8, 16PCS
B. Flange screw M4x8, 12PCS
E. Screw
M4x10x4
F. Flange
nut M6x2
Strap x1
Screw Bag
C. Flange screw M6x50, 8PCS
D. R-Pin, 2PCS
8
4
3
AA
A
A
A
A
AA
A
A
A: Flange screw M5x8, 8PCS
5
5
6
6
7D
D
6
www.camplux.com
Visit Us: Camplux.com
3330-A Marathon Ct Charleston, SC 29418 1(844) 538-7475
3. Assembly the Gas Stand (18).
Using the Screw (E) to lock the two Gas Stand (18)
at the Base(4).
5. Attach the Upper Side Table(H) with the
Bottom-Left Leg Unit(8).
Insert the Side Table Unit(H) into the Bottom-left Leg
Unit(8), and then tighten with the M5 screw(A) to
lock the Side Table Unit(H).
6. Install the rest of the Leg Unit (9) with Side Table
(11).
Insert the Side Table Unit(H) into the Bottom-right
Leg Unit(3) located at the Base Unit(K), and then
tighten with the M5 screw(A) to lock the Side Table
Unit(H). And, pin the Attachment Strap(1) to the
connecting holes of the Leg Unit.
4. Install the rest of the Leg Unit (9) with Side
Table (11).
Using M4 Screw(B) to connect and lock the 2 Leg
Unit(9) with the Side Table(11), total of 2 pairs
should be completed in this step, as shown above.
18
4
E
E: Screw M4x10, 4PCS
11
11
99
9
9
B
BB
B
B
B
BB
B: Flange screw M4x8, 8PCS
H
8K
A
A
AA
A: Flange screw M5x8, 4PCS
A: Flange screw M5x8, 4PCS
K
H
31
A
A
A
A
7
Visit Us: Camplux.com
3330-A Marathon Ct Charleston, SC 29418 1(844) 538-7475
www.camplux.com
7. Assembly the Body(12).
Put the Body(12) in the Base Unit(K), and then using
a total of 8 M6 screw(C), pin through the holes of the
Leg Unit to lock the Body(12).
8. Install the Side Table(11).
Using a total of 4 M4 screw(B), lock the Side
Table(11) at the Body(12).
And then, stabilize the pressure reducing valve with
the strap(1).
9.2. Grill Griddle Net Placement.
Place the Grill Griddle Net(14) inside of the Stove
body(12) as shown above.
9. Installation guide for barbecue
9.1. Flame Spliter(13) Installation.
Place the Grill Griddle Net(14) inside of the Stove
body(12) as shown above.
B: Flange screw M4x8, 8PCS
12
C
CC
C
C
C
C
C
K
11 12
1
B
B
B
B
B
B
C: Flange screw M6x50, 8PCS
13
12
1
12
14
1
8
www.camplux.com
Visit Us: Camplux.com
3330-A Marathon Ct Charleston, SC 29418 1(844) 538-7475
10.2. Placement of the Griddle Plate(15).
Place the Grill Griddle Plate(15) inside of the
Body(12) as shown above.
12. Install the Oil Collector Box(10).
Put up the Grease Cup(10) at the bottom of the
Body(12) as shown above.
10. Installation guide for griddle
10.1. Take out Flame Spliter(13).
Take out Flame Spliter(13) from the body(12) as
shown above.
11. Assembly of the Upper Lid Handle(17).
Tighten the Upper Lid Handle(17) with the Upper
Lid(16) with the nut(F), and then put the completed
Upper Lid on the Body(12) as shown above.
15
1
12
13
12
1
17 16
1
12
F
12
10
F: Flange screw M6x2
9
Visit Us: Camplux.com
3330-A Marathon Ct Charleston, SC 29418 1(844) 538-7475
www.camplux.com
Finished View (Lid Off)
13. Assembly of the Cover Cloth(2).
Install the Cover Cloth(2) at the Leg Unit of the Base through stabilizing it with Velcro Straps, as shown above.
Liquid gas cylinder Placement
2
K
Put the gas cylinder on the base(K), the correct assembly is shown on the right image.
Then connect and tighten the pressure reducing valve to the cylinder in a clockwise direction.
Gas cylinder
Pressure
reducing
valve
K
10
www.camplux.com
Visit Us: Camplux.com
3330-A Marathon Ct Charleston, SC 29418 1(844) 538-7475
Liquid gas cylinder connection
Please note the different national connection options for liquid gas cylinders. Different pressure regulators are used
accordingly.
1. Make sure that all burner control knobs (B) are in the OFF position. Press the control knobs inwards and turn
them clockwise.
2. Determine the controller type and connect the controller to the liquid gas cylinder according to the instructions.
3. Make sure that the gas cylinder valve or the pressure regulator lever is closed.
Note: The pressure regulator supplied may differ slightly from the regulator shown due to national regulations.
A. Connecting the pressure regulator with a lever. Turn the pressure regulator lever (b) clockwise to the OFF
position. Press the pressure regulator onto the liquid gas cylinder valve until the pressure regulator obviously
engages. Turn the lever anti-clockwise to ON so that the gas flows out and you can start up the barbecue.
B. Connecting the pressure regulator with a collar. Make sure that the pressure regulator lever (b) is in the OFF
position. Slide up the collar on the pressure regulator and maintain the pressure. Press the pressure regulator
onto the gas cylinder valve and slide down the collar to close it. If the pressure regulator does not engage,
repeat the procedure.
Removing the pressure regulator:
1. Make sure that the the pressure regulator lever (b) is closed.
2. Turn on all the burner control knobs so that the remaining gas in the system can escape.
3. Now remove the pressure regulator in the opposite order to as described above.
Leakage check:
Open the pressure regulator lever (b) and use a standard leak indicator to check whether all connections on the
gas system and the connection between the gas cylinder and the pressure regulator are tight. For this purpose,
moisten all gas connections with a standard leak indicator or soapy water (80% water, 20% liquid soap). Bubbles
form at leaks in the joints. Observe the instructions for the leak indicator! Never check for leaks using a naked
flame. Listening for leaks is not a reliable method of detection.
If a leak is detected, close the pressure regulator lever (b) immediately and tighten the loose connection or replace
the leaking part.
Repeat the leak test.
A
Pressure
reducing valve
B
Pressure
reducing valve
11
Visit Us: Camplux.com
3330-A Marathon Ct Charleston, SC 29418 1(844) 538-7475
www.camplux.com
The nozzle of the switch valve must be connected to the burner and must not be exposed
to air.
WARNING
WARNING: If "growing" bubbles appear, do not use
or move the gas cylinder. Contact an gas supplier or
your fire department!
If a leak is detected, close the pressure regulator
lever (b) immediately and tighten the loose
connection or replace the leaking part.
Repeat the leak test
WARNING
DANGER: Never search for gas leaks using an
open flame. Before checking for leaks, make sure
that no sparks or open flames can form in the
vicinity.Sparks or flames can cause an explosion
which can lead to serious or even fatal injuries or
material damage.
If a leak is detected, close the pressure regulator
lever (b) immediately and tighten the loose
connection or replace the leaking part.
Repeat the leak test.
DANGER
Proper installation of burner and switch valve's nozzle:
The nozzle of the switch valve must be inside the burner.
Wrong installation:
The nozzle of the switch valve does not be connected to the burner.
12
www.camplux.com
Visit Us: Camplux.com
3330-A Marathon Ct Charleston, SC 29418 1(844) 538-7475
● Risk of burns, some parts of the barbecue can
get very hot. Allow the barbecue to cool down
sufficiently before cleaning it.
● Excessive accumulation of food residues and
cooking fat can lead to a grease fire.
WARNING
Usage & Functions
Functional elements:
A. Electric ignition
B. Main burner control knob
To light
1. Make sure the control knob is in the "OFF" position.
2. Slowly open the valve on the propane gas tank by turning the knob counterclockwise.
3. Push in the control knob and turn to the "LIGHT" position.
4. Push and hold in the electronic igniter button to create sparks within the electrode, continue to hold for 15
seconds.
5. If ignition doesn't occur within a few seconds release the control knob and rotate to the "OFF" position. Wait for 5
minutes for gas to clear and then repeat the above lighting instructions.
6. Once the fire product is lit, the flame intensity may be controlled by turning the control knob between the"LOW"
and "HIGH" positions.
CAUTION: The gas supply must be turned off at the propane supply cylinder when this appliance is not in use.
2
1. First step: Slowly open the valve on the propane gas tank by turning the knob counterclockwise.
2. Second step: Push in the control knob and turn to the "LIGHT" position counterclockwise.
1
Pressure
reducing valve
13
Visit Us: Camplux.com
3330-A Marathon Ct Charleston, SC 29418 1(844) 538-7475
www.camplux.com
Open the cover during the ignition process.
WARNING
Do not bend over the cooking area when igniting the
burners.
WARNING
Each burner can be ignited individually.
WARNING
If the burner has not ignited, press the control knob
and turn it back to the 0 position. Wait for 5 minutes
to allow the gas in the combustion chamber to
dissipate. Then repeat the ignition process.
WARNING
Switching off the grill griddle:
1. Close the gas supply on the gas cylinder.
2. Press the control knob and turn it clockwise to the OFF position.
Cleaning & Maintenance
To ensure your gas barbecue serves you well for many years to come, it should be cleaned after each use.
DANGER! Risk of burns, some parts of the barbecue can get very hot. Allow the barbecue to cool down
sufficiently before cleaning it.
DANGER! Excessive accumulation of food residues and cooking fat can lead to a grease fire.
If the gas barbecue is not cleaned and maintained on a regular basis, its performance may decrease over time.
Low temperatures, uneven heat distribution and food sticking to the grill griddle grid are indications that the
barbecue should be cleaned and maintained. Make sure that the barbecue is switched off and cooled down.
Cleaning and maintenance depends on use.
3. Third step: Push and hold in the electronic igniter button for 15 seconds.
Push and hold in the electronic
igniter for 15 seconds.
14
www.camplux.com
Visit Us: Camplux.com
3330-A Marathon Ct Charleston, SC 29418 1(844) 538-7475
Cleaning the inside of the grill griddle:
● During use, carbon is formed from evaporated fat and smoke and is deposited on the inside of the barbecue.
These brown and black deposits look similar to colour stains, but are not toxic.
● Remove all food residues and fat accumulations in the whole combustion chamber.
● These deposits can be easily removed using a dedicated grill griddle brush.
● Then wipe the surfaces clean using a soft cloth. If there is heavy contamination, you can wash it off using warm
soapy water and wipe it dry with a non-abrasive cloth.
Cleaning the burners:
Clean the entire outer surface of the burners using a wire brush to remove food residue and dirt. Take care not to
bend or damage the ignition electrode during cleaning. Carefully brush around the ignition electrode.
Make sure that the side air inlets are clear on each burner hose. If necessary, clean the air inlet openings, for
example with a pipe cleaner.
The gas outlet nozzles on the adjusters (behind the front panel) can be cleaned with a pin if necessary.
Cleaning the grease collection system:
The Grease Cup is designed for easy removal and cleaning. Empty and clean the grease tray and grease pan
before each use. Old grease is highly flammable and can lead to a grease fire.
Cleaning the outsides:
The outside of the barbecue is made of different materials and surfaces, so we recommend different cleaning
methods depending on the type of surface.
Stainless steel surfacesUse a non-toxic, non-abrasive stainless steel cleaner or polish for outdoor products and
barbecues to clean the stainless steel surfaces. Use a soft cloth for cleaning. Observe the information provided by
the cleaning agent manufacturer.
Painted, porcelain-enamelled surfaces and plastic parts
● Only use warm soapy water and kitchen towels or a soft cloth for cleaning. Clean the surface, rinse and wipe the
surface dry.
● Do not use corrosive or abrasive cleaning agents as they can damage the surfaces.
Note: If the barbecue is exposed to a particularly harsh environment, the outside of the barbecue must be cleaned
more frequently. In environments containing chloride and sulfide, stainless steel can also oxidize or stain.
Especially in coastal areas; saltwater, acid rain, and other extreme conditions, e.g. near pools and whirlpools that
are characterized by high heat and humidity.
These stains are sometimes confused with rust, but they can be easily removed and avoided. Wipe all stainless
steel surfaces every 3 to 4 weeks using tap water and a stainless steel cleaner to prevent staining.
Environmental information and waste disposal measures
Pay attention to cleanliness when using the barbecue and dispose of waste in a clean and safe manner.
Packaging and old equipment must also be disposed of properly.
To dispose of the barbecue, disassemble it into its individual parts and recycle the metal and plastic parts.
This symbol indicates that you must not dispose of this product with household waste.
Old electrical appliances are recyclable materials and should therefore not be disposed
of with household waste.
If you dispose of your barbecue, all electrical components, e.g. electric motor for the spit,
ignition modules, batteries, etc. must be disposed of separately.
We would, therefore, like to ask you to support us with your active contribution to the
conservation of resources and environmental protection and to return these appliances
to the collection points, if available.
Local national regulations apply. For further information, please contact your local administration or consumer
centers.
Visit Us: Camplux.com
3330-A Marathon Ct Charleston, SC 29418 1(844) 538-7475
15
www.camplux.com
Troubleshooting
Leak in the gas system
Replace the gas cylinder
Conduct a visual inspection, connect if
necessary
Gas cylinder is empty
Cylinder valve is closed
Pre-heating was too short
Gas outlets on the burner are
blocked
The nozzle on the adjusting
element (behind front panel) is
not inserted into the burner hose
Fatty foods
Flashback caused by blockages
in the burner
Other gas system blocked
The igniter cable is not on the
igniter
Battery of the electronic ignition
is out
Distance between the spark plug
and gas outlets on the burner is
incorrect
Nozzle on adjusting element
(underneath front panel) is blocked
Problem Possible Cause Solution
There is a smell
of gas
Close the cylinder valve immediatel.
Prevent any flame or spark formation (do not
switch on any electrical appliances).
Tighten all connections on the gas system.
Check all components of the gas system for
visible damage replace defective parts with
original spare parts.
Check for leaks using a leak detector
Burner does not
ignite
Temperature on
grill griddle too
low
Popping or
bubbling noise
Strong flare-up
Open cylinder valve
Visual inspection, if necessary adjust
nozzle and connection hose
Replace battery
Close the cylinder valve immedi-ately.
Wait five minutes and then switch the
barbecue back on.
If the malfunction reoccurs, disassemble and
clean the burner
Visual inspection; correct if necessary
Clean the adjuster jet with a needle
The gas system should be cleaned by
a specialist
Close the lid and set the flame regulator to
max
Remove blockage from burner
Remove any large areas of fat prior to
barbecuing or place the meat on a grill griddle
plate or reduce the barbecue temperature
If the above solutions do not solve your problem, or you need to replace the accessories, please use the phone or
email on the cover to contact us.
16
www.camplux.com
Visit Us: Camplux.com
3330-A Marathon Ct Charleston, SC 29418 1(844) 538-7475
Customer Support
Thank you for purchasing gas griddle from Camplux.
If you need help with product issues, after-sales service or other related issues, please contact us:
Number: 1(844)538-7475, Email:[email protected]
Conforms to ANSI STD
Z21.58-2018 Certified to
CSA STD 1.6-2018 Outdoor
Cooking Gas Appliances
Product Specifications
Model No.
Item No.
BTU
Type Of Gas
Tank Capacity
Cooking Grill Area
Griddle Plate Area
Product Size
Package Size
Net/Gross Weightt
FMGG302B
G2026S
2x10000 BTU
Propane
20 LB
14.7″x13.0″
13.7″x13.1″
36.5″x19.9″x35.1″
21.7″x20.5″x13.0″
30.9/35.2 LBS
17
Visit Us: Camplux.com
3330-A Marathon Ct Charleston, SC 29418 1(844) 538-7475
www.camplux.com
18
www.camplux.com
Visit Us: Camplux.com
3330-A Marathon Ct Charleston, SC 29418 1(844) 538-7475
Table of contents
Languages:
Other Camplux Grill manuals
