MHP GJK 36 Series User manual

GJK Assembly Instructions
Grill Assembly
Instructions
•The GJK 36” Series Grill Model is almost
completely factory assembled.
•Assembly is required for: The locking cast-
ers, side shelves, condiment holders, doors,
hole plugs, grates and briquets.
•Please consult the Owner’s manual for addi-
tional pertinent information regarding im-
portant general safety rules, maintenance,
troubleshooting, etc.
•Leak test all gas connections before using.
•Caution: Combustible material should never
be within 24 inches of the top, bottom, back
or sides of your MHP Gas Barbecue Grill.
Step 1: Locking Casters (See Fig. 1)
The locking casters are packed with the side shelves.
Lift one end of the grill about 12 inches and block it so
it won’t fall. Simply push the casters up into the corner
pocket brackets until they bottom out. Some resis-
tance will be felt so the casters may have to be tapped
up with a block of wood. They should also bottom out
when the grill is set back down. The casters are
locked when the foot tab is in the down position.
Step 4: Attaching the Doors (Fig. 3)
The doors simply drop onto the hinge pins. Hold the door
in the open position (straight out from the grill front) and
carefully match the hinge pins to the door hinges and
push down.
The bottom catch is magnetic, the top catch is a me-
chanical pull catch. On the inside of the right hand door
install the wire condiment holder using two (2) 10-24 x
½” bolts and nuts. Tuck the horizontal wire hooks behind
the door edge.
Complete View of GJK Grill
Step 2: Side Shelves (See Fig. 2)
The side shelves are attached to the main cart with four
¼-20 X ½"bolts and split washers. Simply install one
(1) upper bolt (w/washer) loosely and let the shelf hang.
Then lift, pivoting the shelf while the remaining bolts and
washers are put in and tightened.
Step 3: Condiment Holders See Fig. 2)
Condiment Holders are attached to the front of the side
shelves using the two 10-24 x ½"Stainless Steel
Carriage Bolts and Kep nuts for each holder.
Fig. 2

GJK Assembly Instructions
Step 5: Panel Hole Plugs (See Fig. 4)
Install the three (3) large block panel Hole Plugs and
one (1) medium right Side Shelf Hole Plug. Press in
until they lock. These can be removed later if installing
a Side Burner or a Rotisserie Burner. NOTE: NATU-
RAL GAS MODELS will have a rubber grommet in-
stalled in the lower Back Panel hole for the 12 ft. long
hose to pass through. This will leave only two Side
Panels that need plugs.
Step 8: Electronic Pushbutton (See Fig. 6)
The Electronic Pushbutton Igniter is supplied with an
“AA” Battery which should last several months,
depending on use. Battery placement is easily
accomplished by unscrewing the silver pushbutton. The
button, with battery attached, will be in your hand. The
ignitor mechanism remains in place held with a large
nut. Replace the battery in the same orientation, insert
battery and screw pushbutton on.
DO NOT OVERTIGHTEN the pushbutton when
reinstalling —just finger tighten.
Step 6: Remove Plastic Protective Film
Carefully peel away any remaining white plastic
protective film. Dirt and finger prints may be cleaned
off with a warm soapy water solution or the enclosed
“Flitz” Cleaner, however, please note that stainless
steel is very difficult to “spot clean”. This is true of all
stainless steel and especially when new. It is hard to
clean one spot without noticing the cleaned area. One
might be able to clean a whole panel area easier than
one spot on a panel.
The MHP STAINLESS CLEANER is excellent at
removing the gold patina that will develop over time
on the hood from heat. The Cleaner will also help
prevent future heat stains. Be sure to follow directions
carefully. DO NOT let the Cleaner dry on the surface.
You must have a wet cloth ready to remove the
applied Cleaner, then buff with a dry colth.
Step 7: Before Lighting The Grill (Fig. 5)
Before lighting the grill, especially for the first time,
check the venturi to orfice engagement to make sure
that shippinghas not dislodged the burner placement.
The Venturis should extend over each valve about
1/4” to 7/8” (and there are four (4) to check).
ORIFICE ENGAGEMENT
At the end of each valve there is a tiny gas opening
known as an orifice. Gas exits the orifice and enters
a venturi where it mixes with air coming in the side
air shutter. The proper mixture of air and gas
produces a clean blue flame at the burner.
WARNING! Always check the alignment of the
orifice and the venturi whenever the grill has been
moved. Make sure that the orifice fits into the
venturi tube ¼" to ½". See illustration above.

GJK Assembly Instructions
Step 9: Rock Grates (See Fig. 7)
Install the Rock Grates and arrange the Briquets in
an alternating, interweaved pattern. Start at the back
row and continue forward and across until the grate is
covered. This patern will minimize the amount of
grease tha will reach the burner ports.
Step 10: Gaslow Fuel Monitor & Leak
Detector (Fig. 8)
If so supplied, the small access door on the upper
corner of the left panel will need to be removed to
install the exclusive Upfront Gaslow Fuel Monitor &
Leak Detector.

GJK Parts Information
Parts are divided below into lists associated with the three different grill configurations . When ordering a part
please provide the grill Identification, part number, quantity and product description. To order contact your local
MHP dealer or MHP’s customer service: phone: [phone], fax: [phone], or E-mail: mhp@voyager.
net for the dealer nearest you.
Item Qty. Part # Description
11KK-CP Control Panel
21KK-UBP Upper Back Panel
31KK-LBP Lower Back Panel
41KK-FP Front Pit
51KK-BP Back Pit
61KK-SSR Right Side Shelf
71KK-SSL Left Side Shelf
82KK_CH Condiment Holder
91KK-EPL End Panel (Left)
10 1KK-EPR End Panel (Right)
11 1KK_BAS Lower Base
12 1KK-DC Door Catch
13 1KK-BRC Braces (Not Visible)
14 1KK-DL Left Door (Not Shown)
15 1KK-DR Right Door
16 2KK-BS Burner Support
17 1KK-GT Grease Tray (Full Width)
18 1KK-TSI Stainless Hood
19 1KK-TECL Top Left End Casting
20 1KK-TECR TopRightEndCasting
21 1KK-BECL BottomLeftEndCasting
22 1KK-BECR Bottom Right End Casting
23 4KK-CB Caster Receptacle
24 4KK-WL Locking Casters
25 1KK-DEF Ignitor Shield
26 1KK-IP Instruction Panel
27 4KK-SSB 2 Stainless Steel Bezel
28 4KK-K10 Control Knob
29 1KK-EIB Electronic Module
30 2KK-IW Ignitor Wire
31 2GG-IB SparkCollectorBox
32 2HH-DSB Stainless Steel Burner
33 2KK-DV 13 Venturi
34 2HH-Grate P Rock Grate
35 112 GG-BQ#R Briquets
36 2KK-DPL Door Pull
37 1KK-DCH Door Condiment Holder
38 4KK-PEC Panel Caps
39 1KK-GSH Perforated Stainless Steel
Handle
40 1KK-MAN P Propane Manifold Assembly
1KK-MAN N Natural Manifold Assembly
41 3—–Large Access Hole Plug
42 1—–DisposableGreaseTray
43 1—–Small Access Plug
44 2LPP Lid Hinge Pin
45 2LPP1 Pin Clip
46 1—–Pin Clip
47 1GG-TLG MHP Logo
48 4BR-SG Spider Guard (on each
venturi)
49 1BRMPI Meat Prop Temperature
Gauge
50 1BRSCC Stainless Steel Cleaner (MHP)
50A 1BRFSCC Stainless Steel Cleaner (Flitz)
Item Qty. Part # Description
GJK-NONLY
51 3GG-SS-GRID Stainless Steel Grid
52 1KK-TS Stainless Steel Warming Rack
53 1ASCPL 2 12 Ft. Natural Gas Hose
54 1ASCPL 3 Quick Disconnect Coupler
55 1ASCPL 4 Dust Plug
56 1ASCPL 5 Dust Plug
GJK-NSONLY
57 2GG-GRID-SSearMagic Grid (8” wide)
58 2HH-GRID-SSearMagicGrid (10” wide)
59 1KK-TSS SearMagic Warming Rack
Also #53-56 same as above
GJK-P ONLY
51 3GG-SS-GRID Stainless Steel Grid
52 1KK-TS SearMagic Warming Rack
60 1GSQCC-36 Gaslow Regulator with
Remote Sensor
61 1HIS RegulatorHose
GJK-PSONLY
57 2GG-GRID-SSearMagic Grid (8” wide)
58 1HH-GRID-SSearMagic Grid (10” wide)
59 1KK-TSS SearMagic Warming Rack
60 1GSQCC-36 Gaslow Regulator with
Remote Sensor
61 1HIS RegulatorHose