Canadian Tire 068-7845-8 User manual

Page 1
ASSEMBLY INSTRUCTIONS
** THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Swivel Bar Stool
MODEL NO. 068-7845-8

Page 2
** ASSEMBLE ON A SOFT SURFACE TO PREVENT DAMAGE TO THE PRODUCT FINISH.
** CAREFULLY REMOVE ALL PARTS FROM THE BOX AND MAKE SURE THAT NO PARTS
LISTED ON THE ASSEMBLY INSTRUCTIONS ARE MISSING.
5) FOOT CAP
F) SEAT CUSHION
WITH FRAME (1 PC)
HARDWARE LIST:
BOLT
BOLT
BOLT
12 PCS
1) 1/4 x 1/2" (6 x 12.7 mm)
4 PCS
2 PCS
2) 1/4 x 3/4" (6 x 19 mm)
3) 1/4 x 1 1/4" (6 x 32 mm)
4) 5/8" (16 mm) WASHER 8 PCS
PARTS LIST :
C) SWIVEL (1 PC)A) LEG FRAME (1 PC) D) FOOT-RING (1 PC)B) LEG FRAME (1 PC)
E) LEG EXTENSIONS (4 PCS) G) BACKREST (1 PC)
6) HEX KEY 1 PC
4 PCS
1. ASSEMBLE LEG FRAMES (A, B) BY
INSERTING THE LEG FRAME (B)
(WITH THE CENTRE SLOT ON BOTTOM OF
CROSSBAR), ON TOP OF THE LEG FRAME (A)
(WITH THE CENTRE SLOT ON TOP OF THE
CROSSBAR), AS SHOWN IN FIG. 1.
2. FASTEN SWIVEL UNIT (C) TO LEG FRAMES
(A, B) USING FOUR BOLTS (1) AND FOUR
WASHERS (4),AS SHOWN IN FIG. 1. (THE
SWIVEL IS REVERSIBLE AND MAY BE USED
ON EITHER SIDE.)
FIG.1 1
4
C
B
A

Page 3
3. PLACE THE LEG FRAME ASSEMBLY
UPSIDE-DOWN.
4. ATTACH THE FOOT-RING (D) TO THE LEG
FRAMES (A, B) USING FOUR BOLTS (3)
AND TIGHTENING SECURELY USING
HEX KEY (6), AS SHOWN IN FIG. 2.
5. PLACE SEAT CUSHION (F) UPSIDE DOWN
ON CLOTH-COVERED WORK SURFACE.
(MAKE SURE SEAT FRAME FOR THE LEGS
IS FACING UP.)
6. SECURE LEG ASSEMBLY WITH SWIVEL
UNIT (C) TO SEAT FRAME (F) USING
FOUR WASHERS (4) AND FOUR BOLTS (1),
AS SHOWN IN FIG. 3.
FIG. 2
FIG. 3
D
A
B
3
F
C
1
4
FIG. 4
7. FASTEN THE BACKREST (G) TO THE
ASSEMBLED BARSTOOL USING TWO BOLTS
(2) AND TIGHTEN SECURELY,
AS SHOWN IN
FIG. 4.
2
G
3

Page 4
8. YOU NOW HAVE TWO OPTIONS:
(a) IF YOU CHOOSE A 24" (61 cm) SEAT
HE IGHT: INSERT EACH FOOT CAP (5) ONTO
EACH LEG (A, B).
FIG. 5 (a)
5
A
B
PLACE BARSTOOL UPRIGHT ON THE
FLOOR.

Page 5
A
B
(b) IF YOU CHOOSE A 29" (74 cm) SEAT HEIGHT:
YOU NEED TO INSERT FOUR LEG
EXTENSIONS (E) INTO LEG FRAMES (A, B)
USING FOUR BOLTS (1) AND TIGHTEN
SECURELY.
PLACE BARSTOOL UPRIGHT ON THE
FLOOR.
FIG. 5 (b)
E
1
** CLEANING: WIPE WITH A SOFT CLOTH. NEVER USE HARSH CHEMICALS
OR ABRASIVE CLEANERS FOR POLISHING.
** WE RECOMMEND THAT YOU SAVE THE HEX KEY (6) AND
TIGHTEN ALL BOLTS. PLEASE MAKE SURE ALL BOLTS ARE PLACED IN THEIR
PROPER POSITIONS AND THEN ARE TIGHTENED SECURELY TO ENSURE YOUR
SAFETY.
1