C&T Solution PS-H1701 HMI User manual

PS-H1701
Intel Atom D2550 17”HMI System
User’s Manual
Version 1.0
C&T Solution Inc.
12F. -1, No.700, Zhongzheng Rd., Zhonghe Dist., New Taipei City 235, Taiwan
TEL: [phone]
http://www.candtsolution.com

PS-H1701 Intel Atom D2550 17”HMI System
２
Table of Contents
I. Preface ...................................................................................................５
1.1 Disclaimer.................................................................................５
1.2 Copyright Notice.......................................................................５
1.3 Trademarks Acknowledgment..................................................５
1.4 Environmental Protection Announcement ................................６
1.5 Safety Precautions ...................................................................６
II. Introduction.............................................................................................８
2.1 Product Description..................................................................８
2.2 Specifications ...........................................................................９
III. Mechanical Specification..............................................................１１
3.1 Dimensions............................................................................１１
3.2 Mechanical Layout.................................................................１３
3.2.1 Front View......................................................................１３
3.2.2 Side View.......................................................................１３
3.2.3 Bottom View...................................................................１４
3.2.4 Back View ......................................................................１４
IV. Hardware Installation....................................................................１５
4.1Install Memory Module and SATA HDD ................................１５
4.1.1 Install Memory Module...................................................１５
4.1.2 Install SATA HDD...........................................................１７
4.2 Mounting Bracket Installation ................................................１８
4.2.1 Din Rail Installation.........................................................１８
4.2.2 VESA Mount Installation.................................................２０
4.3 Panel Mount Installation........................................................２２
V. Jumper Setting & Connectors..............................................................２５
5.1 Jumper Position.....................................................................２５
5.2 Jumper Setting ......................................................................２６
5.2.1 JBAT 1: CMOS Clear Jumper ........................................２６
5.2.2 JP1/3: LVDS1/2 VCC 5V/3.3V Select.............................２６
5.2.3 JP2/4: Inverter1/2 VCC 12V/5V Select...........................２６
5.2.4 JCOMP1/2/3/4: COM1/2/3/4 Pin9 Function Select.........２６
5.2.5 JP5: COM 4 RS232/422/485 Function Select................２７
5.2.6 COPEN: Case Open Message Display Function Select.２７
5.3 Connector Position................................................................２８
5.3.1 External Connectors.......................................................２８
5.3.2 Internal Connectors........................................................２９

PS-H1701 Intel Atom D2550 17”HMI System
３
5.4 External Connectors..............................................................２９
5.4.1 DC12V Power Connector...............................................２９
5.4.2 USB 2.0 Connectors.......................................................３０
5.4.3 DVI-I Connector..............................................................３０
5.4.4 RJ-45 LAN Connector....................................................３１
5.4.5 COM Connector: RS-232 ...............................................３１
5.5 Internal Connectors...............................................................３２
5.5.1 SATA II Connectors........................................................３２
5.5.2..............................................................................................３２
5.5.3 SATA Disc Power Connector: PWOUT1........................３２
5.5.4 Serial Port Headers: COM1/COM2/COM3/COM4..........３２
5.5.5 RS422/485 Header: TX-RXCOM1..................................３２
5.5.6 USB Port Headers: USB3/USB4....................................３３
5.5.7 GPIO Header: GPIO.......................................................３３
5.5.8 Front Panel Header: JW_FP1 ........................................３３
5.5.9 Front Panel Audio Header: AUDIO1...............................３３
5.5.10 CIR Header: CIR............................................................３４
5.5.11 CPU FAN Header: CPUFAN1........................................３４
5.5.12 LVDS Inverter: INVERTER1...........................................３４
5.5.13 LVDS Inverter: INVERTER2...........................................３４
VI. SYSTEM BIOS.............................................................................３５
6.1 Main.......................................................................................３６
6.2 Advanced ..............................................................................３７
6.2.1 ACPI Settings.................................................................３８
6.2.2 Wakeup Function Settings .............................................３９
6.2.3 CPU Configuration .........................................................４０
6.2.4 SATA Configuration........................................................４１
6.2.5 USB Configuration..........................................................４２
6.2.6 Super IO Configuration...................................................４３
6.2.7 PC Health Status............................................................４４
6.2.8 Serial Port Configuration................................................４５
6.2.9 Clock Generator Configuration.......................................４６
6.2.10 Watchdog Configuration.................................................４６
6.2.11 Shutdown Temperature Configuration............................４７
6.2.12 PPM Configuration.........................................................４８
6.3 Chipset..................................................................................４９
6.3.1 Host Bridge ....................................................................５０

PS-H1701 Intel Atom D2550 17”HMI System
４
6.3.2 South Bridge...................................................................５１
6.4 Boot.......................................................................................５２
6.5 Security .................................................................................５３
6.6 Save and Exit ........................................................................５４
VII. Address Map ................................................................................５５
7.1 I/O Port Address Map............................................................５５
7.2 Interrupt Controller (IRQ) Map...............................................５７
7.3 Memory Map .........................................................................６０

PS-H1701 Intel Atom D2550 17”HMI System
５
I. Preface
1.1 Disclaimer
All specifications and information in this User’s Manual are believed to be
accurate and up to date. C&T Solution Inc. does not guarantee that the
contents herein are complete, true, accurate or non-misleading. The
information in this document is subject to change without notice and does not
represent a commitment on the part of C&T Solution Inc.
C&T Solution Inc. disclaims all warranties, express or implied, including,
without limitation, those of merchantability, fitness for a particular purpose with
respect to contents of this User’s Manual. Users must take full responsibility for
the application of the product.
1.2 Copyright Notice
All rights reserved. No part of this manual may be reproduced or transmitted in
any form or by any means, electronic or mechanical, including photocopying,
recording, or information storage and retrieval systems, without the prior
written permission of C&T Solutions Inc.
Copyright © 2012 C&T Solutions Inc.
1.3 Trademarks Acknowledgment
Intel®, Celeron®and Pentium®are trademarks of Intel Corporation.
Windows®is registered trademark of Microsoft Corporation.
AMI is trademark of American Megatrend Inc.
IBM, XT, AT, PS/2 and Personal System/2 are trademarks of International
Business Machines Corporation
All other products and trademarks mentioned in this manual are trademarks of
their respective owners.

PS-H1701 Intel Atom D2550 17”HMI System
６
1.4 Environmental Protection Announcement
Do not dispose this electronic device into the trash while discarding. Please
recycle to minimize pollution and ensure environment protection.
1.5 Safety Precautions
Before installing and using the equipment, please read the following
precautions:
Put this equipment on a reliable surface during installation. Dropping it or
letting it fall could cause damage.
The power outlet shall be installed near the equipment and shall be easily
accessible.
Turn off the system power and disconnect the power cord from its source
before making any installation. Be sure both the system and the external
devices are turned OFF. Sudden surge of power could ruin sensitive
components. Make sure the equipment is properly grounded.
When the power is connected, never open the equipment. The equipment
should be opened only by qualified service personnel.
Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
Disconnect this equipment from the power before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning.
Avoid the dusty, humidity and temperature extremes.

PS-H1701 Intel Atom D2550 17”HMI System
７
Do not place heavy objects on the equipment.
If the equipment is not used for long time, disconnect it from the power to
avoid being damaged by transient over-voltage.
The storage temperature shall be above -20℃and below 80℃.
The computer is provided with a battery-powered real-time clock circuit.
There is a danger of explosion if incorrectly replaced. Replace only with
the same or equivalent type recommended by the manufacturer.
If one of the following situation arises, get the equipment checked be
service personnel:
The power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment does not work well or it cannot work according the
user’s manual.
The equipment has been dropped and damaged.
The equipment has obvious signs of breakage.

PS-H1701 Intel Atom D2550 17”HMI System
８
II. Introduction
2.1 Product Description
The PS-H1701 HMI (Human Machine Interface) is powered by Intel Atom
D2550 1.86GHz dual core onboard processor with a 17”touch screen LCD.
The thickness of this panel system is only 5.4cm which is ideal for limited
space. In order to meet the criteria of the harsh industrial environment, the
system also provides optimal shock, vibration and temperature resistance.
The powerful CPU with integrated graphic engine provides a resolution up to
1280 x 1024 pixels. With Intel NM10 chipset, two Ethernet ports, five USB
2.0, two serial ports, and one DVI-I are provided as external I/O interface.
Besides the Cfast socket, the internal SATA interface provides an alternate
storage interface. Also, the extension Mini PCIe interface can be used by
many expansion cards, such as a wireless LAN card. With all these features,
the wide range of applications can be satisfied by the PS-H1701.

PS-H1701 Intel Atom D2550 17”HMI System
９
2.2 Specifications
CPU
Intel Atom D2550 1.86GHz
Chipset
Intel NM10
System Memory
One 204-pin DDR3 SODIMM socket
800MHz or 1066MHz
Up to 4GB
BIOS
AMI uEFI BIOS
16MB SPI Flash ROM
Watchdog Timer
Hardware reset, 1sec-65535sec/min
1 sec or 1 min step
H/W Monitor
LCD Display
Graphic processing unit (GPU) integrated with CPU
17”TFT LCD
Resolution: SXGA (1280x1024)
Brightness: 350 cd/m2
Touch Screen
USB type controller
5-wire Resistive Type
I/O
Display
One DVI-I connector
CRT interface supports resolutions up to
1920x1200
DVI interface supports resolution up to 1920x1200
Ethernet
Realtek RTL 8111E
Two RJ-45 for Gigabit Ethernet

PS-H1701 Intel Atom D2550 17”HMI System
１０
Audio
Realtek ALC662 HD audio codec
One Line-out
Serial Port
Two 9-pin D-sub male connector for RS-232
USB Interface
Five USB 2.0 connectors
Power Input
One 12V DC jack
External 12V@5A, 60W AC/DC power adapter
Expansion Interface
One Mini PCIe
Storage
One 2.5”SATA HDD driver bay
One CFast socket
Power Management
ACPI (Advanced Configuration and Power Interface) 3.0
Temperature
0℃~45℃
Dimension
406.5mm(W) x 333.5mm(H) x 54mm(D)

PS-H1701 Intel Atom D2550 17”HMI System
１１
III. Mechanical Specification
3.1 Dimensions

PS-H1701 Intel Atom D2550 17”HMI System
１２
detachable
reserved for antenna
detachable

PS-H1701 Intel Atom D2550 17”HMI System
１３
3.2 Mechanical Layout
3.2.1 Front View
Power LED: Indicates the power status of the system.
HDD LED: Indicates the status of the hard drive.
3.2.2 Side View
USB: Connects to USB2.0 devices.
DVD-ROM:. Reserved for DVD-ROM option.

PS-H1701 Intel Atom D2550 17”HMI System
１４
3.2.3 Bottom View
LAN: Connect to a local area network.
COM: Connect RS232 compatible serial devices.
DC +12V Input: Plug a DC power cord.
USB: Connects to USB2.0 devices.
DVI-I: Supports either VGA or LCD monitor.
Line-out:Connects to a headphone or speakers.
Brightness Down/ Brightness Up: Adjust the LCD brightness up and down
by pressing the buttons.
Power Switch: Press to power-on or power-off the system.
3.2.4 Back View

PS-H1701 Intel Atom D2550 17”HMI System
１５
IV.Hardware Installation
Make sure the system has been shut down and the power cord has been
unplugged.
4.1 Install Memory Module and SATA HDD
Step 1: Place the system front-side down and remove the 12 screws
“1”, 10 at the back and 2 at the bottom.
Step 2: Remove the rear cover.
4.1.1 Install Memory Module
.
Step 3: Remove the two screws “3”of the DVI-D connector at the
bottom I/O side.
Step 4: After remove the rear cover, locate the SBC close to the
bottom side.
Step 5: Remove the four screws “4”at the four corners of the SBC as
indicated in the diagram below.
Step 6: Remove the SBC from the panel.

PS-H1701 Intel Atom D2550 17”HMI System
１６
Step 7: Insert the plated side of the memory module into the socket.
Step 8: Push the module down until it is firmly locked by two latches.
Step 9: Put the SBC back and fasten all screws.
Step 10: Close the cover and fasten all screws.

PS-H1701 Intel Atom D2550 17”HMI System
１７
4.1.2 Install SATA HDD
Step 3: After remove the rear cover, use four screws to install a pair
of HDD brackets at two sides of a 2.5”SATA HDD as illustrated in the
diagram below.
Step 4: Use four screws to mount the HDD inside the panel.
Step 5: Connect the HDD connector.
Step 6: Close the rear cover and fasten all screws.

PS-H1701 Intel Atom D2550 17”HMI System
１８
4.2 Mounting Bracket Installation
C&T offers two optional accessories for mounting the system.
3-DINR-0002
Din Rail kit
3-VESA-0001
VESA mount kit
4.2.1 Din Rail Installation
Step 1: Use four screws to install the bracket “A”at the back as
indicated in the diagram below. Make sure the latches of the
bracket are facing down.
Step 2: Install the bracket B onto the bracket A by inserting the
latches into the holes, and then push the bracket B upward to wedge
it with the bracket A.
Step 3: Use six screws to mount the din-rail-base C to the bracket B
as shown below.

PS-H1701 Intel Atom D2550 17”HMI System
１９
Step 4: Insert the security screw at the bottom of the din-rail base as
indicated in the diagram below.

PS-H1701 Intel Atom D2550 17”HMI System
２０
Step 5: Make sure the din-rail kit are properly installed on the
system.
Step 6: Before secure the panel with the rail, make sure the rail is
solid and firm to hold the panel.
4.2.2 VESA Mount Installation
Step 1: Use four screws to install the bracket “A”at the back of the
panel as indicated in the diagram below. Make sure the latches of
the bracket are facing down.
Step 2: Install the bracket B onto the desired surface for display the
panel PC by using 6 screws as shown below. Make sure the bracket
is installed in the right direction.
Step 3: Attach the panel PC to the bracket B installed on the surface
by inserting the latches of the bracket A into the holes of the bracket
B.