AMX AXD-CP4 User manual

4" color touch panels
The AMX 4" Color Wall Panel (AXD-CP4) and 4" Color Tabletop Panel
(AXT-CP4) deliver a simple, cost-effective control solution – without
foregoing features you expect from AMX.
Take control by navigating bright, colorful menus and pressing illuminated
command buttons located below the display screen. Intelligent light and
motion sensors recognize when to adjust screen brightness to help
eliminate glareand will instantly turnon the panel as you approach.
The AMX 4" Color Wall Panel (AXD-CP4) mounts easily to a wall, lecternor
any flat surface. Just attach the optional wallbox (CB-CP4) into a surface
and snap in the touch panel for simple, seamless installation.

4" color touch panels
ARGENTINA • AUSTRALIA • BELGIUM • BRAZIL • CANADA • CHINA • ENGLAND • FRANCE • GERMANY • GREECE • HONG KONG • INDIA • INDONESIA • ITALY • JAPAN
LEBANON • MALAYSIA • MEXICO • NETHERLANDS • NEW ZEALAND • PHILIPPINES • PORTUGAL • RUSSIA • SINGAPORE • SPAIN • SWITZERLAND • THAILAND • TURKEY • USA
ATLANTA • BOSTON • CHICAGO • CLEVELAND • DALLAS • DENVER • INDIANAPOLIS • LOS ANGELES • MINNEAPOLIS • PHILADELPHIA • PHOENIX • PORTLAND • SPOKANE • TAMPA
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • 469.624.8000 • +1.469.624.7400 • 469.624.7153 fax • www.amx.com
©2006 AMX. All rights reserved. AMX and the AMX logo are all trademarks of AMX. AMX reserves the right to alter specifications without notice at any time.
AXT-CP4 Tabletop Panel (Rear)AXD-CP4 Conduit/wallbox (front)AXD-CP4 Color Wall Panel (front)
AXD-CP4: 4" COLOR WALL PANEL
•Mounts in a wall, lectern, or any flat surface
•Illuminated, engravable control buttons
•Smart light sensor can adjust LCD brightness to
match environment and turn PDA button
illumination on and off
•Smart motion sensor “wakes-up” LCD backlight
and pushbutton illumination by sensing
proximity and motion
LCD •4" Color passive-matrix LCD with a resolution of
240 x 320 pixels
•Visible area: 3.8 inches (9.65 cm)
POWER
•320 mA @ 12 VDC
MEMORY
•512 KB of SRAM and 2 MB of flash for a total of
2.5 MB (2 MB available for buttons, icons,
bitmaps, and fonts)
DIMENSIONS (HWD)
•AXD Plastic housing: 4.03" x 4.45" x 2.00"
(10.24 cm x 11.30 cm x 5.08 cm)
•Wall Faceplate: 5.13" x 5.25" x 0.40"
(13.03 cm x 13.35 cm x 1.02 cm)
•CB-CP4 Conduit/wallbox: 4.18" x 4.60" x 3.40"
(10.62 cm x 11.68 cm x 8.64 cm)
ENCLOSURE
•Metal sub-plate and bezel with black or white
matte finish
•Detachable front panel faceplate
EXTERNAL BUTTONS
•6fixed-external backlit illuminated pushbuttons
(illumination is user enabled/disabled via the
pushbutton illumination feature)
BUTTON CHARACTERS
•Top row of buttons: 7 characters using a 10pt
Century Gothic font
•Bottom row of buttons: 7 characters using a 7pt
CenturyGothic font
DETECTORS/SENSORS
•Light Detector: Photosensitive light detector for
adjustment of the panel brightness
•PIR Sensor: Proximity Infrared Detector to wake
the panel when movement is detected
REAR CONNECTORS
•AXlink: 4-pin bus connector for connection to
the AMX Central Controller
•RS-232: DB9 male connector for data
transmission or Microsoft® mouse control.
COMPATIBILITY
•Axcess, NetLinx, and Landmark systems (AXlink
is the most common control standard for this
system)
INSTALLATION KIT
•4-pin AXlink data/power connector
•4-#4-40 machine screws and threaded inserts
•Drywall clip set (2-drywall clamps and 2-#8 (2’
long) screws)
INSTALLATION CUTOUT
•Cutout template for the AXD-CP4 is available as
an insert in the product packaging and from
AMX as a drawing. This profile provides 1:1
cutout dimensions for the CP4 conduit/wallbox
OPTIONAL ACCESSORIES
•PSN2.8 Power supply (can be used on the CP4)
•PSN6.5 Power supply (recommended for use on
the CP4)
•Optional spacers and bezels for international
sales
•CB-CP4 Conduit/wallbox (includes flanges for
installation to studs during the construction
phase). The conduit/wallbox should only be
mounted to a beam before a drywall is installed
(pre-wall)
WEIGHT
•4.50 lbs (2.04 kg)
AXT-CP4: 4" COLOR TABLETOP PANEL
•Compact tabletop enclosure
•Illuminated, engravable control buttons can be
dimmed
•Smart light sensor can adjust LCD brightness to
match environment and turn pushbutton
illumination on and off
•Smart motion sensor "wakes-up" LCD backlight
and pushbutton illumination by sensing
proximity and motion
LCD •4" Color passive-matrix LCD with a resolution of
240 x 320 pixels
• Visible area: 3.8 inches (9.65 cm)
POWER
•320 mA @ 12 VDC
MEMORY
•512 KB of SRAM and 2 MB of flash for a total of
2.5 MB (2 MB available for buttons, icons,
bitmaps, and fonts)
DIMENSIONS (HWD)
•AXT Tabletop unit: 4.04" x 5.25" x 4.84"
(10.26 cm x 13.34 cm x 12.30 cm)
•Wall Faceplate: 5.13" x 5.25" x 0.40"
(13.03 cm x 13.35 cm x 1.02 cm)
ENCLOSURE
•Metal sub-plate and bezel with black or white
matte finish
•Detachable front panel faceplate
EXTERNAL BUTTONS
•6fixed-external backlit illuminated pushbuttons
(illumination is user enabled/disabled via the
pushbutton illumination feature)
BUTTON CHARACTERS
•Top row of buttons: 7 characters using a 10pt
Century Gothic font
•Bottom row of buttons: 7 characters using a 7pt
Century Gothic font
DETECTORS/SENSORS
•Light Detector: Photosensitive light detector for
adjustment of the panel brightness
•PIR Sensor: Proximity Infrared Detector to wake
the panel when movement is detected
REAR CONNECTORS
•AXlink: 4-pin bus connector for connection to
the AMX Central Controller
•RS-232: DB9 male connector for data
transmission or Microsoft® mouse control.
COMPATIBILITY
•Axcess, NetLinx, and Landmark systems (AXlink
is the most common control standard for this
system)
OPTIONAL ACCESSORIES
•PSN2.8 Power supply (can be used on the CP4)
•PSN6.5 Power supply (recommended for use on
the CP4)
•Optional spacers and bezels for international
sales
•CB-CP4 Conduit/wallbox (includes flanges for
installation to studs during the construction
phase). The conduit/wallbox should only be
mounted to a beam beforeadrywall is installed
(pre-wall)
WEIGHT
•4.53 lbs (2.05 kg)