Canon MF3110 - ImageCLASS Laser Multifunction Quick start guide

Set-Up Instructions
Set-Up Instructions
Thank you for purchasing Canon imageCLASS MF3110.
To get your machine ready for use, please follow the instructions in this document before referring to any other documentation.
Unpack the machine and its components.
Check that you have the following:
●Machine ●Cartridge
●Power cord
●USB cable
●User Software CD (MF Setup, NewSoft Presto! PageManager, ScanSoft Omnipage SE,
Software Guide)
●Documentation (Set-Up Instructions, Basic Guide, Registration Card, Limited Warranty
Note, Limited Warranty Note for Cartridge X25)
Before setting up the machine:
1Place the machine on a flat, stable surface.
2Remove all shipping tapes from the exterior of the machine.
●Cassette extension ●Extension cover ●Output tray
CF-LDL US1 SI.qxd 6/29/04 10:25 AM Page 1

Install the cartridge.
4Pull open the front cover.
1Remove the cartridge from the bag. Keep the
bag in a safe place for future use.
2Gently rock the cartridge several times to
evenly distribute the toner inside.
3Hold the cartridge on a flat stable surface with
one hand, and break the tab ➊and pull out
the seal ➋completely with the other hand.
B
A
5Hold the cartridge so that the instructions (A)
and the arrow (B) are facing up, and insert it in
the machine horizontally as far as it will go.
6Close the front cover of the machine.
CF-LDL US1 SI.qxd 6/29/04 10:25 AM Page 2

Assemble the cassette and load paper.
3Attach the extension to the cassette. The slots
➊are keyed and must be inserted at a 90°
angle. Once inserted, fold the extension as
shown ➋.
To load Legal-size paper:
Pull the blue tab ➊and extend the cassette ➋as far as it will go. Keep the rear paper end guide to LTR
size mark. If you are not using Legal-size paper, skip to the next step without extending the cassette.
1 Insert the output tray into the front slot on
the machine.
2 Pull out the paper cassette.
4Pinch and slide the rear paper end guide to
match the size of paper.
CF-LDL US1 SI.qxd 6/29/04 10:25 AM Page 3

7Even out the edges of the paper stack.
Make sure the height of the stack does not
exceed the limit marks and that the
side edges of the stack are below the hooks
(B).
9Insert the tabs on the extension cover into
the slots ➊on the back of the machine, and
carefully lower the cover ➋until it sits on
the cassette extension beneath it.
5Load the paper into the cassette. Make sure
the paper stack sits below the hooks (A) .
6Pinch and slide the side paper end guides to
match the size of paper.
A
B
8Insert the paper cassette back into the
machine as far as it will go.
NOTE
●If you do not completely insert the cassette into the
machine, paper jams may occur.
IMPORTANT
●Do not load paper from the back of the machine. Doing
so may damage the paper feeding assembly inside the
machine.
CF-LDL US1 SI.qxd 6/29/04 10:25 AM Page 4

2The machine takes up to 3 minutes to warm up.
Once it is warmed up, the standby display appears in
the LCD.
Connect the power cord.
1Plug the power cord into the rear socket ➊.Then connect the other end to the wall outlet ➋.
IMPORTANT
●For important safety instructions on installation and handling of the machine, see “Important Safety Instructions” in
the Basic Guide.
NOTE
●Make sure the correct paper size is specified in the machine. For details, see Chapter 2,“Paper Handling,” in the Basic
Guide.
CF-LDL US1 SI.qxd 6/29/04 10:25 AM Page 5

Install the software.
IMPORTANT
●Do not connect the USB cable before installing the software. If you connect the USB cable before installing the software
and the Found New Hardware Wizard screen appears, click [Cancel] and disconnect the USB cable.
NOTE
●The instructions below are for Windows XP. For Windows 98/Me/2000, see the Software Guide (included in the User
Software CD).
●For Windows 2000/XP, log on as Administrator to install the software.
1Turn on your computer.
2Quit any open applications, including virus checking software.
3Insert the User Software CD into the CD-ROM
drive.
4When the MF Setup screen appears, click
[Install MF Drivers].
●If the MF Setup screen is not displayed, on the
Windows desktop, click [start] ➝[My Computer].
Open the CD-ROM icon, then double-click [Setup
(Setup.exe)].
5When the MF Drivers Setup screen appears,
click [Yes] and follow the instructions on the
screen.
6When the installation is complete, click
[Finish] to close the MF Drivers Setup screen.
CF-LDL US1 SI.qxd 6/29/04 10:25 AM Page 6

7On the MF Setup screen, click [Install MF
Toolbox].
8When the MF Toolbox Setup screen appears,
click [Next] and follow the instructions on the
screen.
NOTE
●Before installing MF Toolbox, make sure that all other
applications are closed and that any anti-virus software on
your computer is disabled.
9When the installation is complete, click [Finish]
to close the MF Toolbox Setup screen.
CF-LDL US1 SI.qxd 6/29/04 10:25 AM Page 7

Part no. FA7-6215 (000)
©2004 Canon Inc.
Canon and imageCLASS are trademarks of Canon Inc.
All other products and brand names are registered
trademarks or trademarks of their respective owners.
Specifications subject to change without notice.
PRINTED IN CHINA
Congratulations! You have now completed the machine setup.
Where to go from here...
Once you have completed all steps in this document, see the Basic Guide for basic
operations of all functions of your machine.
For information on the driver software, see the Software Guide (included in the User
Software CD).
NOTE
●Remember to register your machine to ensure product support. The serial number is located on the back of the
machine.
Connect the machine to your computer.
1Make sure the machine’s power is turned on.
Connect the cable to the USB port on the
back of the machine.Then connect the other
end of the cable to the USB port on your
computer.
2After the installation is complete, click [Exit]
to close the MF Setup screen. Remove the
User Software CD from the CD-ROM drive
and store it in a safe place.
NOTE
●If you would like to install the optional Presto! PageManager file management software and/or OmniPage OCR software,
click [Install Applications] and follow the instructions on the screen.
●You can also click [Read Manuals] to read PDF manuals in the User Software CD. To view the manuals in PDF format,
Adobe Reader/Acrobat Reader/Acrobat is required. If Adobe Reader/Acrobat Reader/Acrobat is not installed on your
system, please download it from the Adobe Systems Incorporated website (http://www.adobe.com).
For installation help and operational instructions, call us at:
1-800-828-4040 1-800 OK CANON
U.S.A. CUSTOMERS CANADA CUSTOMERS
CF-LDL US1 SI.qxd 6/29/04 10:25 AM Page 8