Canon PIXMA MX432 Manual

<< Previous Next >>
Installing Your Multifunction
to Your Network for the First Time
PIXMA MX432 / MX439
Macintosh OS
1

<< Previous Next >>
Installing Your Multifunction
to Your Network for the First Time
PIXMA MX432 / MX439
Macintosh OS
Preparing to Connect My Multifunction to My Network 3
Network Requirements 3
Notes on Wireless Connection 4
Installing the Drivers & Software 5
2

Preparing to Connect My Multifunction
To My Network << Previous Next >>
Network Requirements
Before connecting the machine to the network, make sure that configuration of the computer and access point or router is
complete, and that the computer is connected to the network.
Wireless Connection
Before connecting the machine to the network, the computer needs to be connected to the network. Make sure that
configuration of the computer and access point or router is complete.
3

Preparing to Connect My Multifunction
To My Network << Previous Next >>
4
Notes on Network Connection
•The configuration, router functions, setup procedures and security settings of
the network device vary depending on your system environment. For details,
refer to your device's instruction manual or contact its manufacturer.
•In an office setup, consult your network administrator
•If you connect to a network that is not protected with security measures, there
is a risk of disclosing data such as your personal information to a third party.
•If an error message appears or if you have trouble with the network
connection, refer to the printed manual: Network Setup Troubleshooting.
•Place the machine and computer on the same network segment.
An "Ad-hoc connection," which establishes a direct wireless connection between
the computer and printer without using an access point, is not supported.
A router or access point is required for your printer to be used on a wireless
network.

Software Installation
To use the machine by connecting it to a computer, software including the drivers needs to be copied (installed) to the computer's hard disk. The
installation process takes about 20 minutes. (The installation time varies depending on the computer environment or the number of application
software to be installed.)
Installing the Drivers & Software
5
IMPORTANT
•Log on as the administrator (or a member of the Administrators group).
•Quit all running applications before installation.
•Do not switch users during the installation process.
•Internet connection may be required during the installation. Connection fees may apply. Consult the internet service provider.
•It may be necessary to restart your computer during the installation process. Follow the on-screen instructions and do not remove the
Setup CD-ROM during restarting. The installation resumes once your computer has restarted.
•If the firewall function of your security software is turned on, a warning message may appear that Canon software is attempting to access
the network. If such a warning message appears, set the security software to always allow access.
<< Previous Next >>

Installing the PIXMA MX432 / MX439 on Your Wireless Network
If you are installing your printer on your network for the first time, a step-by-step walk through of the wireless setup is built in to the
installation routine of the software that shipped with your PIXMA.
*Insert the Setup CD-ROM that came with your printer into your CD-ROM drive and proceed through the easy to follow instructions.
*If you don’t have or cannot use the Setup CD-ROM, you can still install the printer using a downloaded file. Click here for information.
If the following screen appears, click Continue Installation
Installing the Drivers & Software
6
<< Previous Next >>
Continue following on-screen instructions until the Connection Method Selection (1-1) screen appears. This is shown on the next
page..

Installing the PIXMA MX432 / MX439 on Your Wireless Network
Select Wireless Connection on the Connection Method Selection screen
Installing the Drivers & Software
7
<< Previous Next >>
Continue carefully following the Preparation for Connection (1-2) and Printer Setup instructions (Steps 2-1 through 2-5) until the
Setup Procedure Selection screen (3-1) appears. This is shown on the next page.

Installing the Drivers & Software
8
<< Previous Next >>
The printer automatically searches for access points that support WPS (Wi-Fi Protected Setup)*.
*Unless you are absolutely sure your access point supports WPS and you are familiar with activating this on your access point, press the
Stop button on the printer’s operation panel and click on Other Methods on the Setup Procedure Selection screen (screenshot shown
below)*.
If the Push Button Method is not shown on the printer’s operation panel(when no WPS access points have been detected), select Standard
setup on the printers operation panel, then click Other Methods on the Setup Procedure Selection screen
If you selected the Push Button Method, follow any remaining
instructions to complete setup. Skip ahead to instructions
If you selected Other Methods, please continue to the next page for
important information

Installing the Drivers & Software
9
<< Previous Next >>
On the Setup Procedure Selection screen (3-2) screen, select Wireless Setup Using the USB Cable. This is the recommended setup method.
You will need to use the supplied USB cable
Continue to follow any on-screen instructions until the Software Installation List appears. This screen is shown on the next page

Installing the Drivers & Software
10
<< Previous Next >>
On the Software Installation List select any additional* software to install and click Next.
*MP Drivers is required for installation and cannot be deselected. In addition, we recommend installing MP Navigator EX and Easy-
PhotoPrint EX in order to take full advantage of your printer’s features.
*If you are using the downloaded ‘Mini Master setup’ file to install the printer, only the MP Drivers and Canon IJ Network Tool will be
installed. Additional software can be downloaded separately. The software can be found in the Software section of Drivers & Software
(the same page where you downloaded the Mini Master setup file)
If you selected the Push Button Method to set
up your connection, continue to follow any
remaining on-screen instructions to finish and
exit setup.
If you are using the Wireless Setup Using the
USB Cable connection procedure, continue to
the next page.