Canon PowerShot SX730 HS User manual

CEL-SX1HA210
ENGLISH
Getting Started

2
Package Contents
Package Contents
Before use, make sure the following items are included in the package.
If anything is missing, contact your camera retailer.
Camera Battery Pack
NB-13L*1
Battery Charger
CB-2LHE
Wrist Strap*2
*1 Do not peel off the adhesive covering from a battery pack.
*2 For attachment instructions, refer to the Camera User Guide that can be downloaded
from the Canon website.
• Printed matter is also included.
• A memory card is not included.
Compatible Memory Cards
No memory card is included. Purchase one of the following kinds of card
as needed. These memory cards can be used, regardless of capacity. For
details on the number of shots and recording time per memory card, see
“Specifi cations” in the downloadable Camera User Guide.
• SD memory cards*1
• SDHC memory cards*1*2
• SDXC memory cards*1*2
*1 Cards conforming to SD standards. However, not all memory cards have been
verifi ed to work with the camera.
*2 UHS-I memory cards are also supported.

3
Manuals and Software
Manuals and Software
You can download the manuals and software from the following
URL.
http://www.canon.com/icpd/
•With a computer connected to the Internet, access the above URL.
•Access the site for your country or region.
•Adobe Reader is required to view the manuals.
•You can also download software from the above URL. For instructions on
downloading and installing the software, refer to the Camera User Guide
available for download.
•You may be requested to enter the serial
number (body number) when downloading the
manuals or software.
In this case, enter the number on the camera
body, behind the screen (monitor).
Initial Preparations
Initial Preparations
1 Attach the strap.
 Thread the end of the strap through the
strap mount (1), and then pull the other
end of the strap through the loop on the
threaded end (2).
2 Insert the battery pack.
 After aligning the marks on the battery
pack and charger, insert the battery pack
by pushing it in (1) and down (2).
(1)
(2)
(1)
(2)

4
Initial Preparations
3 Charge the battery pack.
 Plug the power cord into the charger, then
plug the other end into a power outlet.
 The charging lamp turns orange, and
charging begins.
 When charging is fi nished, the lamp turns
green. Remove the battery pack.
 For details on charging time and the
number of shots or recording time
available with a fully charged battery
pack, refer to “Specifi cations” in the
downloadable Camera User Guide.
4 Open the cover.
 Slide the switch (1) and open the cover
(2).
5 Insert the battery pack.
 Holding the battery pack with the terminals
in the position shown, hold the battery
lock toward (1) and insert the battery pack
toward (2) until the lock clicks shut.
 If you insert the battery pack facing the
wrong way, it cannot be locked into the
correct position. Always confi rm that the
battery pack is facing the right way and
locks when inserted.
 To remove the battery pack, press the
battery lock in the direction of the arrow.
(2)
(1)
(1)
(2)

5
Initial Preparations
6 Check your card’s write-protect
switch and insert the memory card.
 Recording is not possible on memory
cards with a write-protect switch when the
switch is in the locked position. Move the
switch toward (1).
 Insert the memory card with the label (2)
facing as shown until it clicks into place.
 To remove the memory card, push it in
until you feel a click, and then slowly
release it.
7 Close the cover.
 Lower the cover (1) and hold it down as
you slide the switch, until it clicks into the
closed position (2).
 If the cover will not close, make sure you
inserted the battery pack facing the right
way in step 2.
8 Turn the camera on.
 Press the ON/OFF button.
 The [Date/Time] screen is displayed.
9 Set the date and time.
 Press the [ ][ ] buttons to choose an
option.
 Press the [ ][ ] buttons or turn the [ ]
dial to specify the date and time.
 When fi nished, press the [ ] button.
(2)
(1)
(1)
(2)