Canon imageCLASS LBP122dw User manual

En
Es
Fr
Pt
Setup Guide
• After you finish reading this guide, store it in a safe
place for future reference.
• The information in this guide is subject to change
without notice.
https://oip.manual.canon/
1Important Safety Instructions
Be sure to read these instructions before using
the machine.
3User's Guide
This section explains all the ways this machine
can be used.
FAQ
This section describes problems that may arise
and how to resolve these problems.
2Setup Guide (this document)
See p. 6“Accessing the Online Manual” for details.

2
En
Es
Fr
Pt
Checking the Items
Included
Removing the Packing
Material
1. Install the machine in the location where it
will be used.
2. Remove all packing material.
Remove all of the tape.
Do not remove the sticker that covers the USB port
until you actually use the USB port.
Rear
1
2
1234567 11

En
Es
Fr
Pt
3
Loading Paper
1.
2.
3.
4.
3
Ensure that the amount of paper
loaded is not above this line
5.
Setting Up the Paper
Stopper
1
2
Connecting the Power Cord
2
1
Rear
4
5
1 2 3 4 5 6 7 11

En
Es
Fr
Pt
4
Specifying the Basic
Settings
When you turn on the machine for the first time, the Setup
Guide appears on the operation panel. Perform the initial
machine setup by following the on-screen instructions.
Operation panel
1. Select the language, the country or region,
and then the time zone.
2. Set the current date/time.
Specifying the Security
Settings
To prevent unauthorized access to the machine, set access
restrictions for Remote UI.
What is Remote UI?
Remote UI allows you to use your computer’s Web
browser to check the machine’s operating status
and change settings.
1. To use the Remote UI, select <Yes>.
To continue without using the Remote UI, select
<No> and proceed to step 8.
2. Check the message and press .
3. To set the Remote UI Access PIN here, select
<Yes>.
• Set the PIN used to access the Remote UI.
• To set the PIN later, select <No> and proceed to
step 8.
6
7
4. Set the Remote UI Access PIN.
• Enter any number and then select <Apply>.
• Re-enter the same PIN on the next screen as
confirmation and select <Apply>.
Specifying the Network
Settings
Specify the settings for connecting the machine to a
network. Before proceeding, check that the computer and
router are correctly connected to the network.
• You cannot use a wired LAN and a wireless LAN at the
same time.
Wireless LAN
1. Check the router’s“SSID”and“Network key.”
SSID : XXXXXXXXXXXX
Network key : XXXXXXXXXXXX
2. To configure the settings, select <Yes> on
the operation panel.
3. Select the network with a matching SSID.
4. Enter the password (network key) and select
<Apply>.
5. Select <Yes> to connect using the selected
settings.
Select <No> to return to the previous screen.
8
45678 111

En
Es
Fr
Pt
5
Wired LAN
Connect the router to the machine with a LAN cable and
then select <No> in the screen for choosing how to
connect to the network.
Rear
Setting Up the Toner
Replenishment Service
Use this procedure to set up the toner replenishment
service. To use this service, you must enter into an
agreement beforehand.
1. Select an option based on whether you
subscribed to the toner replenishment
service when you purchased the machine.
• If you subscribed to the service, select <Yes>.
• If you did not subscribe to the service, select
<No> and proceed to step 10 .
2. Check the message and press .
3. Check the conditions of use, and then
choose whether or not to use the service.
• To use the service: <Accept>.
• To not use the service or not enter into an
agreement: Select <Do Not Accept> and proceed
to step 10 .
4. When <Connection was successful.> appears,
press .
Ending the Setup Guide
1. Check the message and press .
To save the date/time settings, the battery must be
charged for 24 hours. After you end the Setup Guide,
be sure to leave the mains power to the machine ON
for at least 24 hours.
9
10
Installing the Software/
Drivers
To use the print function of the machine, you must install
the printer driver.
Downloading from the Canon website
1. Search for“(model name) download.”
Example: LBP122dw download
XXXXXXX download
If you cannot find the download site, go to
https://global.canon/en/support/
2. Download the software and drivers, and
install them on your computer.
Installing from the Bundled CD/DVD-
ROM
1. Load the CD/DVD-ROM into your computer,
and install the software and drivers.
For normal installation, select “Easy Installation.”
Selecting “Easy Installation” installs the drivers along
with the standard software and manuals.
If a problem arises during the installation, see
“Questions Related to Drivers”in “FAQ.”
Accessing the FAQ
p. 6 “Accessing the Online Manual”
11
5 6 7 8 109111