CANOPY STAR CNP-50 Series User manual

INSTALLATION GUIDE
CNPx-50
Page 1
#44-000017
Updated 04.20.18
US LED | 6807 PORTWEST DR | HOUSTON, TX 77024 | T 866 972 9191 | F 713 972 9393 | [email protected] | www.usled.com
The installation must only be performed by a licensed electrician.
To prevent death, injury or damage to property, this product must be installed in accordance to National
Electrical Code (NFPA70) in the US or Canadian Electrical Code (CSA22.1) in Canada.
Disconnect power before installing the product or servicing it.
Wait until xture has cooled down before installing or servicing the xture.
MIN. 90°C SUPPLY CONDUCTORS
WARNING
l
l
l
l
l
MODEL NUMBERS
This installation instructions covers the following products:
Power Supplies
1. 96W Power Unit: PUC-UNV1-3570 or PUC-UNV2-3570
2. 100W Power Unit PUC-UNV1-4100 or PUC-UNV1-4100DM or PUC-UNV2-4100DM
3. 192W Power Unit: PUC-UNV1-7140 or PUC-UNV2-7140
4. 200W power Unit: PUC-UNV1-8200 or PUC-UNV1-8200DM or PUC-UNV2-8200DM
Luminaires
1. CNP1-50 Series Luminaire
2. CNP2-50 Series Luminaire
3. CNP3-50 Series Luminaire
4. CNP4-50 Series Luminaire
BOX CONTENTS
Mounting Plate Assembly
Wire Harness/Cover
Assembly
CanopyStar Fixture
LED Driver with Mounting Bracket
sold separately not included in
the box
Tools Needed
1. 4” Hole Saw
2. #2 Phillips Screw Driver
3. ¼” Hex Driver

Page 2
CNPx-50
INSTALLATION GUIDE
#44-000017
Updated 04.20.18
US LED | 6807 PORTWEST DR | HOUSTON, TX 77024 | T 866 972 9191 | F 713 972 9393 | [email protected] | www.usled.com
1. Using4”holesaw,cutholeincanopywherextureistobemounted.Holelocationneedstobecenteredbe-
tweencanopyribstoallowwireharness/coverassemblytot.
2. Install mounting plate assembly by folding mounting tabs in, insert mounting plate into 4” hole and secure by
tightening mounting tab screws using #2 Phillips screw driver. See Figures 1 and 2.
INSTALLATION INSTRUCTIONS
4” hole
Mounting tabs
FIG 1 FIG 2
Mounting tab
screws
FIG 3 FIG 4
3. Hang Canopy Fixture on mounting plate assembly by hooking hinge on mounting plate hook. Secure by sliding
locking plate forward into slot and tightening #6-32 locknut. See Figures 3 and 4.
Locking plate
Locknut

INSTALLATION GUIDE
CNPx-50
Page 3
#44-000017
Updated 04.20.18
US LED | 6807 PORTWEST DR | HOUSTON, TX 77024 | T 866 972 9191 | F 713 972 9393 | [email protected] | www.usled.com
4. Route wires through center of mounting plate assembly. See Figure 5.
5. Take wire harness assembly and make power connections using approved electrical connector.
See wire diagrams.
INSTALLATION INSTRUCTIONS
FIG 5 FIG 6
FIG 7 FIG 8
6. Pack excess wire in center of mounting plate assembly and mount cover using #10 sealing weather resistant
screws supplied. See Figure 7.
7. Completeinstallationbyswingingxtureintoplaceandsecuringwithmountingscrewsusing#2Phillipsdriver.
See Figure 8.

Page 4
CNPx-50
INSTALLATION GUIDE
#44-000017
Updated 04.20.18
US LED | 6807 PORTWEST DR | HOUSTON, TX 77024 | T 866 972 9191 | F 713 972 9393 | [email protected] | www.usled.com
1. Turnomainpower.
2. Secure driver box assembly to mounting bracket by tightening mounting screws using ¼” hex driver.
See Figure 9.
3. Secure mounting bracket to any vertical wall using #10 sheet metal screws supplied. Insure location allows wire
harness to reach low voltage side of power supply box. See Figure 10.
4. Make internal primary side (high voltage) power connections by connecting wires, Black to Load, White to Neu-
tral and Green to Ground using approved electrical connector. See wire diagrams.
5. Make secondary (low voltage) connections by using approved electrical connector. See wire diagrams.
6. Secure driver box top using #8 sealing machine screws supplied.
7. Turn on power.
INSTALLATION INSTRUCTIONS - DRIVER BOX
FIG 9 FIG 10
Mounting screws

INSTALLATION GUIDE
CNPx-50
Page 5
#44-000017
Updated 04.20.18
US LED | 6807 PORTWEST DR | HOUSTON, TX 77024 | T 866 972 9191 | F 713 972 9393 | [email protected] | www.usled.com
WIRING DIAGRAMS
WITH TRANSFORMER
WITHOUT TRANSFORMER
FOR CNP1-50 LUMINAIRES

Page 6
CNPx-50
INSTALLATION GUIDE
#44-000017
Updated 04.20.18
US LED | 6807 PORTWEST DR | HOUSTON, TX 77024 | T 866 972 9191 | F 713 972 9393 | [email protected] | www.usled.com
WITHOUT TRANSFORMER, 2 DRIVERS
WIRING DIAGRAMS
WITH TRANSFORMER, 2 DRIVERS
FOR CNP2-50 LUMINAIRES

INSTALLATION GUIDE
CNPx-50
Page 7
#44-000017
Updated 04.20.18
US LED | 6807 PORTWEST DR | HOUSTON, TX 77024 | T 866 972 9191 | F 713 972 9393 | [email protected] | www.usled.com
347-480VAC INPUT VOLTAGE
WIRING DIAGRAMS
FOR CNP3-50 LUMINAIRES
120-277VAC INPUT VOLTAGE

Page 8
CNPx-50
INSTALLATION GUIDE
#44-000017
Updated 04.20.18
US LED | 6807 PORTWEST DR | HOUSTON, TX 77024 | T 866 972 9191 | F 713 972 9393 | [email protected] | www.usled.com
WIRING DIAGRAMS
FOR CNP4-50 LUMINAIRES
347-480VAC INPUT VOLTAGE
120-277VAC INPUT VOLTAGE