CANOPY US LED CNP-1-50 Series User manual

INSTALLATION GUIDE
CNP-1-50
Page 1
US LED | 6807 PORTWEST DR | HOUSTON, TX 77024 | T 866 972 9191 | F 713 972 9393 | [email protected] | www.usled.com
Updated 09.21.12
#44-000017
The installation must only be performed by a licensed electrician.
To prevent death, injury or damage to property, this product must be installed in accordance to National
Electrical Code (NFPA70) in the US or Canadian Electrical Code (CSA22.1) in Canada.
Disconnect power before installing the product or servicing it.
Wait until xture has cooled down before installing or servicing the xture.
MIN. 90°C SUPPLY CONDUCTORS
WARNING
l
l
l
l
l
MODEL NUMBERS
This installation instructions covers the following products:
Power Supplies
1. 50W Power Unit: PUC-UNV1-2100
2. 75W Power Unit: PUC-UNV1-3000
3. 96W Power Unit: PUC-UNV1-3570
Luminaires
1. CNP-1-50 Series Luminaires
BOX CONTENTS
Mounting Plate Assembly
Wire Harness/Cover
Assembly
CanopyStar Fixture
LED Driver with
Mounting Bracket
Tools Needed
1. 4” Hole Saw
2. #2 Phillips Screw Driver
3. ¼” Hex Driver

Page 2
US LED | 6807 PORTWEST DR | HOUSTON, TX 77024 | T 866 972 9191 | F 713 972 9393 | [email protected] | www.usled.com
Updated 09.21.12
CNP-1-50
INSTALLATION GUIDE
#44-000017
1. Using4”holesaw,cutholeincanopywherextureistobemounted.Holelocationneedstobecenteredbe-
tweencanopyribstoallowwireharness/coverassemblytot.
2. Install mounting plate assembly by folding mounting tabs in, insert mounting plate into 4” hole and secure by
tightening mounting tab screws using #2 Phillips screw driver. See Figures 1 and 2.
INSTALLATION INSTRUCTIONS
4” hole
Mounting tabs
FIG 1 FIG 2
Mounting tab
screws
FIG 3 FIG 4
3. Hang Canopy Fixture on mounting plate assembly by hooking hinge on mounting plate hook. Secure by sliding
locking plate forward into slot and tightening #6-32 locknut. See Figures 3 and 4.
Locking plate
Locknut

INSTALLATION GUIDE
CNP-1-50
Page 3
US LED | 6807 PORTWEST DR | HOUSTON, TX 77024 | T 866 972 9191 | F 713 972 9393 | [email protected] | www.usled.com
Updated 09.21.12
#44-000017
4. Route wires through center of mounting plate assembly. See Figure 5.
5. Take wire harness assembly and make power connections using approved electrical connector. Connect Red
wire to Red wire and Blue wire to Blue wire. See Figure 6.
INSTALLATION INSTRUCTIONS
FIG 5 FIG 6
FIG 7 FIG 8
6. Pack excess wire in center of mounting plate assembly and mount cover using #10 sealing weather resistant
screws supplied. See Figure 7.
7. Completeinstallationbyswingingxtureintoplaceandsecuringwithmountingscrewsusing#2Phillipsdriver.
See Figure 8.

Page 4
US LED | 6807 PORTWEST DR | HOUSTON, TX 77024 | T 866 972 9191 | F 713 972 9393 | [email protected] | www.usled.com
Updated 09.21.12
CNP-1-50
INSTALLATION GUIDE
#44-000017
1. Turn off main power.
2. Secure driver box assembly to mounting bracket by tightening mounting screws using ¼” hex driver.
See Figure 9.
3. Secure mounting bracket to any vertical wall using #10 sheet metal screws supplied. Insure location allows wire
harness to reach low voltage side of power supply box. See Figure 10.
4. Make internal primary side (high voltage) power connections by connecting wires, Black to Load, White to Neu-
tral and Green to Ground using approved electrical connector.
5. Make secondary (low voltage) connections by connecting wires, Blue to Blue and Red to Red using approved
electrical connector.
6. Secure driver box top using #8 sealing machine screws supplied.
7. Turn on power.
INSTALLATION INSTRUCTIONS - DRIVER BOX
FIG 9 FIG 10
Mounting screws