CAPBRAN HOLDINGS magic bullet MBR-0307AK User manual

user guide.

32
The cup and blade are
consumable components, over
time, if the unit starts to get
louder or make unusual noise or
vibration, it indicates that these
consumable parts may need
replacing. The continued use of
worn parts may result in part
failure and/or personal injury.
This appliance is not intended
for use by persons (including
children) with reduced physical,
sensory or mental capabilities,
or lack of experience and
knowledge, unless they have
been given supervision or
instruction concerning use of
the appliance by a person
responsible for their safety.
warning:
If you are taking any
medication, especially
cholesterol-lowering
medication, blood thinners,
blood pressure drugs,
tranquilizers, or antidepres-
sants, please check with your
physician before consuming
any magic bullet®recipes.
The following list of seeds
and pips contain chemicals
that release cyanide into the
body when ingested. Do not
use: apple seeds, apricot
seeds, cherry pips, plum
pips, and peach pips in your
magic bullet®.
VERY IMPORTANT: If there is a
liquid spill, immediately
disconnect the unit from the
power source. If the spill is
external only, clean with a warm
soapy cloth and allow unit to dry
completely before operating.
If the spill has leaked in to the
internal components of the
power base, cease use
immediately. Unit must be
checked by a Qualified
Electrician and certified as
electrically safe before using
again. Failure to do so will
result in a possible electric
shock and/or personal injury.
To avoid risk of electric shock,
never immerse the cord, plug, or
power base of blender in water
or other liquids.
Switch o the appliance and
disconnect from power supply
before changing accessories or
handling moving parts. At all
times, avoid contact with moving
parts. Keep hands and utensils
away from the extractor blade.
TO REDUCE THE RISK OF
PERSONAL INJURY OR LEAKAGE,
make sure the extractor blade is
securely twisted (hand-
tightened) onto the magic
bullet® blending cup before
placing it on the motor base.
Check to make sure the easy-
twist extractor blade is aligned
properly before placing it on
the motor base and operating
your magic bullet® .
important safeguards.
Warning! To avoid the risk of serious injury, carefully read all
instructions before operating your magic bullet®. When using any
electrical appliance, basic safety precautions should always be
observed, including the following important information.
Save These Instructions!
FOR HOUSEHOLD USE ONLY
personal safety:
NEVER PUT HOT LIQUIDS IN ANY
OF THE SEALED BLENDING
CUPS BEFORE BLENDING.
Start with cold or room
temperature ingredients. Heated
ingredients can create internal
pressure in a sealed blending cup,
which may erupt on opening and
cause thermal injury.
Friction from the rotating blade
will cause ingredients to heat
and generate internal pressure
in the sealed cup. Do not
continuously operate for more
than one minute. If the cup is
warm to touch, allow to cool
before carefully opening pointed
away from your body.
Never permit any blended
mixture to sit inside a sealed
vessel without first releasing
internal pressure. If storing
blended ingredients, remove
the blade from the cup and
replace with the flip top lid.
Never store the extractor blade
on the power base without a cup
or vessel attached. Failure to do
so may result in personal injury if
the unit is accidently turned on.
NEVER leave spoons or other
foreign objects in the cup before
blending. Failure to do so will
result in damage to the cup and/
or possible personal injury.
Never leave the magic bullet®
unattended while it is in use.
Close supervision is necessary
when any appliance is used by or
near children.
Never blend carbonated
ingredients or liquids. Built-up
pressure from released gases
can cause the blade and cup to
separate, possibly resulting in
personal injury.
!

54
Extractor blades are
sharp! Handle carefully.
Do not remove the seal from
your blade attachment. The seal
is not designed to be removed. If
seal is removed, cease use
immediately and purchase a
replacement.
If, over time, the extractor blade
becomes loose or damaged, you
may order a new extractor blade
at: www.bulletbrands.com.au /
www.bulletbrands.co.nz
or contact customer service:
Australian Consumers:
1300 285 538
New Zealand Consumers:
0800 232 633
The cups and blades are
consumable components. We
recommend replacing your
stainless steel cross blade
every 6 months for optimal
performance. If, over time, the
cross blade becomes loose,
damaged, or needs replacing,
you may order a new cross
blade at: bulletbrands.com.au /
bulletbrands.co.nz or contact
customer service.
Blade attachments should not
be placed in the dishwasher
for cleaning. Exposure to hot
water can cause damage to
the seal in the outer rim of the
attachment. Always inspect
your blades before each use.
Use of adapters and converters
is considered an unauthorized
modification of the product and
as such will void the warranty.
product safety:
To prevent the overheating of
the ingredients being blended,
never allow the unit to run
continuously for more than
1 minute.
If the motor stops for any reason,
unplug the power base and let it
cool for at least 15 minutes.
If the magic bullet®malfunctions
or is dropped, or damaged in any
manner, discontinue use and
contact Customer Service for
further assistance.
NEVER USE THE MAGIC
BULLET®WITHOUT ADDING
LIQUID OR WHEN THE CUP IS
EMPTY, AS DOING SO MAY
DAMAGE THE BLADE
TO AVOID LEAKAGE, DO NOT
OVERFILL THE CUP. Your magic
bullet®cups are also marked
with a MAX line. When filling the
cup or pitcher, make sure your
ingredients do not exceed their
respective MAX lines.
The magic bullet®is not
intended for use in microwave
ovens. Do not place the magic
bullet®cups, power base or any
accessories in a microwave as
this may result in damage to
the appliance.
The use of attachments not
recommended or not sold by the
manufacturer will void warranty
and may cause fire, electric
shock, or injury.
Use of this product in locations
with dierent electrical
specifications may result in
damage to the product.
warning:
ventilation caution
Always operate the magic
bullet®on a level surface,
leaving unobstructed space
beneath and around the power
base to permit proper air
circulation. Slots and openings
on the bottom of the product
are provided for ventilation to
ensure reliable motor
operation and to prevent
over-heating.
To prevent fire hazard,
power base openings should
be free of dust or lint and
never obstructed with
flammable materials such as
newspapers, tablecloths,
napkins, dishtowels, or
place mats.
caution:
In order to avoid a hazard due
to inadvertent resetting of the
thermal cut-out, this
appliance must not be
connected to an external
switching device, such as a
timer, or connected to a circuit
that is regularly switched on
and o by the utility.
Periodically inspect cord and
plug for damage. Do not
operate any appliance with a
damaged cord or plug. If
damaged, it must be replaced
by the manufacturer, its service
agent, or similarly qualified
persons in order to avoid a
hazard.
Do not allow the cord to hang
over the side of the counter or
table. Do not allow the cord to
touch hot surfaces, including
stove.
The cyclonic action of your
magic bullet®requires the use of
liquids to make smoothies and
other nutritious beverages. The
magic bullet®is not intended to
be used as an ice crusher and
not intended to be used without
liquids. To make a delicious cold
smoothie, we suggest that you
use frozen fruit and chilled
liquids. Alternatively, you may
add crushed ice, up to 25% of
the total cup volume, with water
or other liquid filled up to the
“MAX” line. Do not crush ice or
other hard items without liquid,
as such prolonged use over time
may dull or damage the blades.
Unplug the magic bullet®when
it is not in use. Make sure the
power base is unplugged before
assembling, disassembling, adding
additional parts, or cleaning.
Do not use magic bullet®
outdoors. If exposed to
inclement weather elements
such as rain or other wet
conditions, discontinue use.

76
Unplug the magic bullet®when it
is not in use. Make sure the power
base is unplugged before
assembling, disassembling, adding
additional parts, or cleaning.
Periodically inspect your magic
bullet®cups for damage or wear
that may impair proper function.
Discontinue use and replace
components if you detect
cracking, crazing or cloudiness/
discolouration, or other damage
to the plastic cups, or tabs (on the
side of the cup). You may
purchase new cups and cross
blades at www.bulletbrands.com.
au, www.bulletbrands.co.nz
or contact Customer Service:
Australian Consumers:
1300 285 538
New Zealand Consumers:
0800 232 633
Save these
instructions!
FOR HOUSEHOLD
USE ONLY
!

98
contents.
10 what’s included
11 assembly guide
12 using the magic bullet®
14 care and maintenance
15 replacement parts
16 magic bullet®one-year
limited warranty
thank you for purchasing the magic bullet® .

1110
assembly guide.what’s included.
tall cup
stainless steel
cross blade
motor base tall cup
short cup
party mug
2 stay-fresh
resealable lids
to-go lid
stainless steel
cross blade
motor base
2 lip rings
Product configurations
may vary. To see our full
list of magic bullet®
accessories please visit:
www.bulletbrands.com.au
www.bulletbrands.co.nz

1312
caution:
Before using the Cross Blade,
check the gasket to make sure it is
not damaged and it is completely
seated in the Cross Blade Unit
before each use.
Never put your hands or utensils
near the moving Cross Blade and
never use your hands or utensils to
press the activator buttons down
while the Motor Base is plugged in.
If the Cross Blade stops spinning
while in lock on mode, immediately
unplug the magic bullet®
.Hard
ingredients like carrots or celery
can get stuck in the Cross Blade
and stop it from turning. If this
happens, unplug the magic bullet®
right away. Remove the blade/cup
assembly from the Motor Base,
and give ingredients a good shake
to unblock the Cross Blade. If the
Cross Blade still remains
obstructed, twist the Cross Blade
attachment off of the Cup and
carefully spin the metal blades
using a utensil (not your fingers) to
release the blockage. Reattach the
Cross Blade to the Cup, plug in the
magic bullet®and try again. It
should spin normally.
Never run the magic bullet®for
more than one minute at a time, as
it can cause permanent damage
to the motor. If the motor stops
working, unplug the Motor Base
and let it cool for a few hours
before attempting to use it again.
Your magic bullet®has an internal
thermal breaker that shuts the unit
off when it overheats. Letting the
thermal breaker cool down should
allow it to reset.
Using the
magic bullet®
.
3Twist on the Cross Blade
until the blade and Cup
are tightly sealed.
2Load the ingredients into
the Cup (do not exceed
the MAX line).
4Line up the tabs on the
Cup and with the tabs on
the Motor Base. Press the
Cup down onto the base
to turn on the machine.
Here’s how it works:
The magic bullet®will
blend for as long as you
press the Cup down onto
the Motor Base. To stop
blending, simply release
pressure on the Cup.
Using the magic bullet®is as easy as 1, 2, 3:
1Before first use, review all warning and caution statements in
the Important Safeguards section (pages 2–6). Clean Blending
Cups and Cross Blade with hot, soapy water before use.
storing leftovers in the
magic bullet®cups
The magic bullet®includes Stay
Fresh Resealable Lids that twist
directly onto your magic bullet®
Cups, allowing you to prep food
ahead of time, keep leftovers
fresh, or take your meal on the
go without dirtying an extra
storage container.
“Lock-on” mode:
For hands-free operation,
press down and gently turn the
Cup clockwise until the tabs
lock under the lip of the Motor
Base. Once you are in lock-on
mode, the motor will run
continually (do not run for
longer than a minute!). To stop
blending, simply twist the Cup
counter-clockwise to release.

care & maintenance.
Cleaning the magic bullet®is easy. Simply place any of the parts
(except for the Motor Base and Cross Blade) on the top rack of the
dishwasher or hand wash with warm, soapy water and rinse.
step 1: Always power off and
unplug the Motor Base from
the outlet when it is left
unattended, before assembling,
disassembling, changing
accessories or approaching
parts that move in use or when
cleaning. Do not attempt to
handle the appliance until all
parts have stopped moving!
step 2: Make sure the
Blending Cup/Cross Blade is
not attached to the Motor Base.
step 3: Clean the individual
components (Motor Base,
Cross Blade, magic bullet®
Blending Cups).
motor base:
• To avoid risk of injury, never
use your hands or utensils to
clean the White Actuator Tabs
while the magic bullet®is
plugged in.
• Never submerge the Motor
Base in water or put in the
dishwasher.
• Do not remove the rubber
or plastic liners inside the
Motor Base.
• Use a sponge or dish cloth
dampened with warm soapy
water to wipe down the inside
and outside of the Motor
Base until clean.
• Pay particular attention to
the actuator tabs on the
inside of the Motor Base to
loosen any stuck or sticky
debris from drips and spills.
If necessary you may use a
small brush to scrub the area
to ensure it is kept clean.
cross blade:
DO NOT REMOVE THE GASKET
AS THIS MAY PERMANENTLY
DAMAGE THE CROSS BLADE
AND CAUSE LEAKAGE
• If after washing as indicated
additional disinfecting is
desired, you may rinse with
a 10% vinegar/water solution.
If, over time, the gasket
becomes loose or damaged,
you may order a new Cross
Blade at:
www.bulletbrands.com.au
www.bulletbrands.co.nz.
• Dry the Cross Blade
completely. It is helpful to turn
the blade on its side in your
dish drainer to ensure both
sides of the Cross Blade are
completely dried.
replacement
parts.
To order additional parts and
accessories, please visit our
website at:
www.bulletbrands.com.au
www.bulletbrands.co.nz
• We recommend replacing
your magic bullet®Cross
Blade every 6 months or
as needed for optimal
performance. To order
replacement Cross Blades,
simply visit:
www.bulletbrands.com.au
www.bulletbrands.co.nz.
blending cups
cups, lids and lip rings:
• These items are all Top
Rack dishwasher safe. We
recommend rinsing them
and giving them a quick
brush with a dish brush to
remove any dried debris
before washing them in the
dishwasher. Never use the
sanitize cycle to wash the
blending cups as this may
warp the plastic.
• Regularly check the tabs (3)
on the sides of the Cups for
damage (cracking, crazing,
breakage or rounding).
If the tabs are damaged,
discontinue use and replace
immediately to prevent
possible personal injury.
1514

1716
If your product becomes
defective due to faulty
material or workmanship
within a period of 1 year from
the date of purchase, we
warrant to do the following:
• For New Zealand Consumers:
We will replace the product
with a new product, free of
charge, or repair the product
at our cost, at our discretion.
• For Australian Consumers:
Our goods come with
guarantees that cannot be
excluded under the
Australian Consumer Law.
You are entitled to a
replacement or refund for a
major failure and for
compensation for any other
reasonably foreseeable loss
or damage. You are also
entitled to have the goods
repaired or replaced if the
goods fail to be of acceptable
quality and the failure does
not amount to a major
failure.
one (1) year limited
replacement warranty
statement.
YOUR WARRANTY
IS SUBJECT TO THE
FOLLOWING CONDITIONS:
• DO NOT operate the
appliance with a damaged
plug or cord, or if the unit has
been dropped, damaged or
dropped in water. To avoid
the risk of electric shock, do
not disassemble or attempt
to repair the appliance on
your own. If the supply cord is
damaged, it must be
replaced by a qualified
electrician in order to avoid a
hazard. Incorrect re-
assembly or repair can cause
a risk of electric shock or
injury to persons when the
appliance is used.
• The item has not been
misused, abused, neglected,
altered, modified or repaired
by anyone.
• The item has been subjected
to fair wear and tear.
• The item has not been used
for trade, professional or
hire purposes.
• The item has not sustained
damage through foreign
objects, substances or accident.
YOUR WARRANTY
DOES NOT COVER:
• Components that are
subject to natural wear and
tear caused by normal use
in accordance with
operating instructions.
• Unauthorised/improper
maintenance/handling or
overload is excluded from
this warranty.
• For guarantee claims, you
will need to submit a proof
of purchase in the form of a
valid receipt that displays
date and place of purchase.
This warranty does not replace
but is in addition to your
statutory rights.
This warranty does not apply
to accessories supplied with
the item.
This warranty applies only to
the original purchaser and may
not be transferred.
Replacement items will be
covered by the limited
warranty for the balance of the
warranty period from the date
of the original purchase.
PLEASE NOTE:
Only the defective product or
parts returned to place of
purchase will be replaced under
this warranty.
NEW ZEALAND
PO Box 100-707
NSMC
Auckland 0745
0800 232633
www.bulletbrands.co.nz
AUSTRALIA
PO Box 574
South Morang
Victoria 3752
1300 285538
www.bulletbrands.com.au
magic bullet®is a registered trademark of CapBran Holdings, LLC.
Copyright © 2022 CapBran Holdings, LLC. All rights reserved.
Los Angeles, CA 90025, USA. Made in China.

1918