Capital SL ECO Series User manual

1
INSTALLATION AND OPERATING
INSTRUCTIONS
APPROVED - CONFORMING TO EN13240:2001 and
EN13240 A2:2004
APPLICABLE TO THE FOLLOWING STOVE MODELS:
VEGA EDGE 200SL (ECO)
AVEBURY (ECO)
BASSINGTON (ECO)
SCENE (ECO)
SIGMA (ECO)
STOVES MUST BE FITTED BY APPROVED, QUALIFIED AND
COMPETENT INSTALLERS
PLEASE LEAVE THIS BOOKLET WITH THE HOUSEHOLDER
Stoves operate at very high temperatures. All persons
including children and the infirm should be warned of this and not
allowed to touch any surfaces whilst in use. The operator must use
the glove provided.
SL ECO SERIES INSTRUCTION –REV.C –NOV 2018
These appliances have been approved by HETAS Ltd as an intermittent operating appliance for
burning wood and approved smokeless fuels at the nominal output of 5.0kW only.

2
AVEBURY (ECO)
SCENE (ECO)
BASSINGTON (ECO)
STANDARD LEGS
BASSINGTON (ECO)
SKIRTED LEGS
BASSINGTON (ECO)
BASELINE LEGS
SIGMA (ECO)
VEGA EDGE 200SL (ECO)

3
CONTENTS
STOVE DIMENSIONS, OUTPUT & EFFICIENCY PAGE 04
INSTALLATION PAGE 05
OPERATION PAGE 11
GENERAL MAINTENANCE PAGE 17
SAFETY NOTES & TROUBLESHOOTING PAGE 19
STOVE ACCESSORIES PAGE 22
COMPONENT PARTS PAGE 23
TECHNICAL FICHE PAGE 30

4
STOVE DIMENSIONS, OUTPUT AND EFFICIENCY
For illustrative purposes the Vega Edge 200SL is shown above and throughout this
manual. Other stove models may have a different appearance.
A
B
C
D
E
F
G
H
I
J
AVEBURY (ECO)
531mm
630mm
80mm
325mm
114mm
350mm
365mm
453mm
590mm
531mm
BASSINGTON (ECO)
BASELINE LEGS
500mm
615mm
80mm
317mm
114mm
317mm
364mm
443mm
575mm
511mm
BASSINGTON (ECO)
SKIRTED LEGS
500mm
640mm
105mm
317mm
114mm
317mm
364mm
468mm
600mm
511mm
BASSINGTON (ECO)
STANDARD LEGS
500mm
615mm
80mm
317mm
114mm
324mm
364mm
443mm
575mm
530mm
SCENE (ECO)
485mm
635mm
95mm
327mm
114mm
324mm
352mm
456mm
595mm
504mm
SIGMA (ECO)
500mm
645mm
105mm
313mm
114mm
322mm
369mm
468mm
605mm
536mm
VEGA EDGE 200SL (ECO)
501mm
634mm
80mm
309mm
114mm
336mm
380mm
454mm
590mm
501mm
*See page 10 for ventilation requirements.
Outputs stated are under ideal test conditions carried out at SGS Environmental Services in the
Netherlands. Variations may occur due to installation, atmospheric conditions and fuel quality.
WOOD
ANTHRACITE
EFFICIENCY
84%
71.5%
FLUE GAS TEMPERATURE
244 ˚C
280˚C
EMISSION OF CO @ 13% O2
0.11%
0.24%
RATED OUTPUT
5.0kW
5.0kW
OUTPUT RANGE*
2.5 –8.0kW
2.5 –8.0kW
A
B
D
C
E
F
G
H
I
J

5
INSTALLATION, OPERATION AND MAINTENANCE
IMPORTANT: THIS APPLIANCE MUST BE INSTALLED BY A COMPETENT PERSON AND THE
INSTALLATION MUST COMPLY WITH BS8303 –CODE OF PRACTICE FOR INSTALLATION OF
DOMESTIC HEATING AND COOKING APPLIANCES BURNING SOLID MINERAL FUEL, NATIONAL
BUILDING REGULATIONS, LOCAL BY-LAWS AND STANDARDS AND THE REQUIREMENTS OF THE
HEALTH AND SAFETY AT WORK ACT - IN PARTICULAR:
HANDLING –ADEQUATE FACILITIES MUST BE AVAILABLE FOR LOADING, UNLOADING AND SITE
HANDLING.
FIRE CEMENT –SOME TYPES ARE CAUSTIC AND SHOULD NOT BE ALLOWED TO COME INTO
CONTACT WITH THE SKIN. IN CASE OF CONTACT WASH IMMEDIATELY WITH PLENTY OF WATER.
ASBESTOS –THESE STOVES CONTAIN NO ASBESTOS. IF THERE IS A POSSIBILITY OF DISTURBING
ANY ASBESTOS IN THE COURSE OF INSTALLATION THEN PLEASE SEEK THE GUIDANCE OF A
SPECIALIST AND USE APPROPRIATE PROTECTIVE EQUIPMENT.
METAL PARTS –WHEN INSTALLING OR SERVICING THIS STOVE CARE SHOULD BE TAKEN TO AVOID
THE POSSIBILITY OF PERSONAL INJURY
UNLESS THE INSTALLER IS QUALIFIED TO APPROVE INSTALLATION THEN APPROVAL MUST BE
SOUGHT FROM YOUR LOCAL BUILDING CONTROL DEPARTMENT. THE SUPPLIERS ACCEPT NO
RESPONSIBILITY IF THIS ADVICE IS NOT FOLLOWED. THIS APPLIANCE HAS BEEN EXTENSIVELY
TESTED FOR SAFETY AND EFFICIENCY, DO NOT ATTEMPT TO MODIFY IT. ALWAYS USE GENUINE
REPLACEMENT PARTS AS RECOMMENDED BY YOUR SUPPLIER. FAILURE TO ADHERE TO THIS
ADVICE WILL INVALIDATE YOUR GUARANTEE.
TRY TO AVOID FITTING AN EXTRACTOR FAN IN THE SAME ROOM AS THIS STOVE. IF THIS IS
UNAVOIDABLE THEN SEEK SPECIALIST ADVICE TO ENSURE THAT THE INSTALLATION IS TESTED
FOR SAFETY. A SUITABLE TEST COMPRISES CHECKING FOR SPILLAGE IF THE ROOM WHERE THE
APPLIANCE IS FITTED IS SUBJECTED TO THE GREATEST POSSIBLE DEPRESSURISATION. THIS
MEANS FIRING THE APPLIANCE WITH ALL THE EXTRACT FANS IN THE BUILDING OPERATING AT
THEIR MAXIMUM AND WITH ALL DOORS, ADJUSTABLE VENTILATORS AND WINDOWS CLOSED.
IF SPILLAGE OCCURS THEN ADDITIONAL PERMANENT VENTILATION DIRECT FROM OUTSIDE WILL
BE REQUIRED. ONCE THE ADDITIONAL VENTILATION IS FITTED, RETEST AS NOTED ABOVE,
IT IS ESSENTIAL AND REQUIRED BY BUILDING REGULATIONS THAT A CARBON MONOXIDE (CO)
ALARM IS INSTALLED IN THE SAME ROOM AS THIS STOVE.
THIS STOVE MUST HAVE ITS OWN CHIMNEY AND MUST NOT SHARE A CHIMNEY WITH ANOTHER
APPLIANCE.
THIS STOVE IS FOR INTERMITTENT USE ONLY AND SHOULD BE SHUT DOWN OVERNIGHT.
VENTILATION MAY BE REQUIRED INTO YOUR ROOM, PLEASE SEE PAGE 10.

6
INSTALLATION
Once the installation is complete, the installer must advise the householder on
the correct use of the stove and warn them to use only the recommended fuels
listed in this document. The installer must also advise the householder on the
actions to be taken should smoke or fumes be emitted from the stove.
This stove must not share a chimney with any other appliance
Where the chimney is believed to have previously served an open fire
installation it is possible that the higher flue gas temperature from a closed
appliance may loosen deposits that were previously firmly adhered, with the
consequent risk of flue blockage. It is therefore recommended that the chimney
be swept a second time within a month of regular use after installation.
Check the chimney is in good condition, dry, free from cracks, leaks and
obstructions. The diameter of the flue should be no more than 230mm. If this
cannot be met then an appropriate liner should be fitted by a suitably approved
method.
A 125mm flue liner may be used in accordance with the Building Regulations.
The chimney and connecting flue pipe should not narrow to less than the size of
the outlet socket (collar) of the stove at any point. It is essential that only
recommended fuels are used –see page 15 for more information.
The chimney height and the position of the chimney terminal must conform to
Building Regulations and the latest edition of BS EN 15287-1:2007, Design,
Installation and Commissioning of Chimneys should be followed.
A flue draught of minimum 12 Pascals is required for satisfactory appliance
performance. The flue draught should be checked under fire at high output and
if it exceeds 25Pa, a draught stabiliser may be required so that the rate of
burning can be controlled, and to prevent possible over-firing.
If you have any doubts about the suitability of your chimney, consult your local
dealer/stockist. He will also be able to provide advice about the possible need
for a specialist cowl.

7
The chimney must be swept before connection to the stove and swept every
twelve months thereafter. It is recommended that your chimney is swept every
six months.
An existing fireplace opening can be modified to accommodate the stove. The
following pages identify some typical installation scenarios and provides the
necessary specific installation information for your new stove. Always consult
your stove supplier for a detailed survey of your particular circumstances.
To make it easier to handle the stove on installation, remove the baffle plates,
bricks and door. Place in a secure place to avoid damage. Refit after
installation.
Upon completion of installation, the appliance should be checked under fire for
soundness of joints and seals, and also that all smoke and fumes are taken from
the appliance, up the chimney and emitted safely.
Typical Installation for Inglenook Fireplaces –top flue
Inglenook fireplaces can have very
large bore chimneys. Check with your
installer –you are likely to require a
stainless steel flexible liner for solid
fuel if your chimney is larger than
230mm x 230mm. A closure plate
with access for cleaning may also be
required together with a short length
of flue pipe of the same diameter as
the stove flue collar.

8
Typical Installation for Inglenook Typical Installation Into In-filled
Fireplaces –rear flue –Side View Masonry Fireplaces
SPECIFIC INSTALLATION INFORMATION
Legs
Remove the legs from inside the stove. Note that the Bassington legs are not
contained inside the stove but packaged separately. Carefully lay the stove on
its back and using the screws provided fit the legs in place. Carefully set the
stove upright and check that all internal components are correctly positioned.
Clearances
If the stoves are to be installed adjacent to materials that can catch fire like
wood then the following clearances must be adhered to:
Clearance to rear = 600mm
Clearance to sides = 600mm
The stove can be recessed into a suitably sized fireplace built from non-
combustible materials, but a permanent free air gap of at least 100mm should
be left around the sides and top to obtain maximum heat output and for access
to the rear of the stove.
MINIMUM 600MM STRAIGHT
BEFORE 45 DEG BEND.

9
It is possible to fit the stove with less clearance around it –down to 50mm, but
the non-combustible material around it must be at least 150mm thick. This is
normally achieved when installing into a standard brick-built chimney breast
with double thickness walls to the rear and sides of the builder’s opening. Take
care that the wall finish is suitable to withstand temperatures of up to 200oC.
Hearths
Allow an apron of at least 225mm at the front of the stove and 150mm on either
side. Care should be taken to level the stove and secure the hearth. If existing
floors do not have adequate load bearing capacity then suitable modifications
must be adopted.
When the stove is in the desired position, fix the brackets provided to the back
feet and level the stove using the levelling screws, then mark the hearth through
the holes, remove the stove, and drill and plug the hearth for securing the stove.
Light Duty Hearths
Excluding the Bassington Baseline model, so long as the stove is installed in
accordance with the minimum clearance distances below then a light duty
hearth may be placed on a wooden floor. Note that all clearance distances to
combustible materials must be adhered to (see page 8).
1
12mm
NON-COMBUSTIBLE
MATERIAL HEARTH

10
Ventilation Into a Room For Combustion Air is an Essential Requirement.
Any apertures provided for this purpose must not be restricted or blocked.
Flues Without a Flue Draft Stabiliser 2.5kW-5kW Output
When installing without a flue draft stabiliser into houses built before 2008, no
additional permanent ventilation will be required.* Houses built after this date will
require additional means of permanent ventilation direct to outside of at least 4400
mm2. * Note: Installers must verify adequate draw and install ventilation if required. See Appendix F of
Building Regulations Approved Document J.
5kW-8kW Output - If you are intending to burn the stove above the independently
tested 5kW output, then a permanently open air vent into the room where the stove is
situated will be required. For house built before 2008, the vent must have a free area of
at least 1650mm2. For house built after 2008, the vent must have a free area of at least
4400mm2.
Flues With a Flue Draft Stabiliser 2.5kW-5kW Output
When installing with a flue draft stabiliser into houses built before 2008, at least
1500mm2additional means of permanent ventilation direct to outside is required.
Houses built after this date will require additional means of permanent ventilation direct
to outside of at least 6800 mm2.
5kW-8kW Output - If you are intending to burn the stove above the independently
tested 5kW output, then a permanently open air vent into the room where the stove is
situated will be required. For house built before 2008, the vent must have a free area of
at least 4050mm2. For house built after 2008, the vent must have a free area of at least
6800mm2.
Top or Rear Flue
Remove the collar and accessory pack from the stove. The
stove will arrive with the blanking plate fitted to the rear.
This can be removed if required allowing the collar to be
fitted for rear flue installations. The circular cut out in the
rear heat shield must be removed to enable this style of
connection –see image.
Remove the panel from the stove by unscrewing the four
screws and then remove the circular cut out for rear flue
installations. Replace the rear heat shield. Remember to fit
the blanking plate to the unused flue position if it has been
removed.
SCREWS

11
OPERATION
SLIDING PRIMARY AIR CONTROL TYPE
ROTARY PRIMARY AIR CONTROL TYPE
Secondary Air Control
Riddling Mechanism
Primary Air Control
Secondary Air Control
Riddling Mechanism
Primary Air Control

12
Primary Air –Slide Control
ALWAYS OPEN THE STOVE DOOR SLOWLY AND ALWAYS USE THE GLOVE
Primary air is controlled via the sliding vent in the bottom of the door. This
provides an air draught to the bed of the fire. Slide right to open and left to
close. Open this when you start a fire, and to regulate anthracite fires. It should
be closed when a wood fire is established for the best efficiency.
Primary Air –Slide Control
Slide right to open and left to close. Open this when you start a fire, and to
regulate anthracite fires. It should be closed when a wood fire is established for
the best efficiency.
Primary Air –Rotary Control
Rotate clockwise to open and anti-clockwise to close. Open this when you start
a fire, and to regulate anthracite fires. It should be closed when a wood fire is
established for the best efficiency.
Secondary Air
Secondary air is controlled via the sliding vent above the door, it is this ‘airwash’
that keeps a clean and uninterrupted view of the fire, also aiding good
secondary combustion of fuel and reducing emissions into the chimney and
environment. Slide to the right to open and to the left to close. Use this to
control wood fires. It should be closed when burning anthracite for the best
efficiency after the fire is established.
Tertiary Air
A tertiary air supply is bled into the stove from the rear panel. Its function is to
ignite unburned gasses assisting with a clean burn. It is advisable to clear these
holes from time to time with a brush, especially when the stove is being serviced
or after long periods of burning. ONLY CARRY OUT THIS AND ALL SERVICING
PROCEDURES WHEN THE STOVE IS COLD. This tertiary air supply is permanently

13
open and allows a small amount of air into the stove. Operation with air
controls open can cause excess smoke. These stoves must not be operated with
air controls left open except as directed in these instructions.
Lighting the Stove
It is essential that you have three or four small fires before you operate the
stove to its maximum heat output. This is to allow the paint to cure and to
“temper” your cast iron stove. We recommend this ‘running-in’ procedure after
long shutdowns to preserve the life of stove. During the curing of the paint you
may notice an unpleasant smell. It is not toxic, but for your comfort we would
suggest that during this period you leave doors and windows open.
First, load the fire with starting fuel i.e. paper, dry kindling timber (about the
thickness of your thumb) and/or firelighters in the mode chosen, either wood or
coal products. It is normal to see smoke come from the open stove door at this
stage.
Light the fire at base leaving all air controls fully open. Allow the fuel to reach a
steady glow and build up the fire gradually. Once you have a good fire
established across the fire bed, further fuel can be added as required.
When your fire is well established you can start to restrict the primary air intake.
If you are burning only wood, the primary air control can be fully closed. If you
are burning solid fuel you will require some primary air. Your stove is burning
with maximum efficiency when a bright fire is achieved using minimum air inlet
and a stove thermometer (purchased separately) registers within the “Best
Burn” range.
Wood Burning
Wood burns best on a bed of ash and it is therefore only necessary to remove
surplus ash from the grate occasionally. Burn only kiln dried or well-seasoned
wood, which should have been cut, split and stacked under cover for at least 36
months, with free air movement around the sides of the stack to enable it to dry
out. Burning wet or unseasoned wood will create tar deposits in the stove and
chimney and will reduce heat output. Tar deposits, if allowed to build up, are a
major cause of chimney fires. This tar also is the main cause of blackened stove
windows. A wood moisture meter is a handy device to have.

14
Once established and for the best results from your stove, load 1kg of good
quality dry wood per 45 minute period with the primary air control fully closed
and the secondary air control about half to two-thirds closed. Logs can be up to
300mm or 12” long. If you are intending to burn the stove above the
independently tested 5kW output, then do not exceed a load of 2kg of good
quality dry wood per 45 minute period with the air controls in the same position
as noted above.
Of course, best burning depends on the quality of wood, draft and stove
settings, so please do experiment to find your own best settings and the best
position on your stove thermometer.
Other Solid Fuel Burning
Always clean out the ash pan before refuelling and do not let the ash build up to
the underside of the grate bars –this will severely reduce the life of the grate
and prevent efficient burning. Solid fuel produces ash, which if allowed to build
up, will stifle the air flow through the grate and eventually cause the fire to die.
Caution –only empty the ash pan when the stove is cool.
With some solid fuels a residue of burnt fuel or clinker will accumulate on the
grate, allow the fire to go out periodically to remove this.
Once established and for the best results, load about .75 kg of anthracite or
equivalent per 45 minute period with the primary air control about half way
open and the secondary air control fully closed. If you are intending to burn the
stove above the independently tested 5kW output, then do not exceed a load of
1.5kg of anthracite or equivalent per 45 minute period with the air controls in
the same position as noted above.
When loading fuel, ensure that the series of tertiary air holes on the rear
chamber brick are not covered by the fuel.
Of course best burning depends on the type of fuel being burnt, draft and stove
settings, so please do experiment to find your own best settings.

15
De-Ashing
During stove use, whilst burning anthracite or a mix of wood and anthracite,
from time to time the riddler must be used to remove ash ensuring airflow
through the fire bed and allowing the fire to burn over the whole grate. The
riddling knob is located on the right hand side of the stove. The supplied stove
tool must be used to turn this knob. Placing the ‘spanner’ end of the tool over
the knob, rotate the tool clockwise and anti-clockwise –back and forwards until
the fire shows signs of more air reaching un-burnt fuel. Do not force this
mechanism if it becomes very hard to move –there may be some debris caught
in the grate –if this is the case, carefully open the stove and using a poker in a
gloved hand, gently agitate the fuel bed.
Recommended Fuels
Please note that HETAS Ltd Appliance Approval only covers the use of wood logs
and approved smokeless fuels on this appliance. HETAS Ltd. Approval does not
cover the use of other fuels either alone or mixed with the recommended fuels
listed above, nor does it cover instructions for the use of other fuels
Wood - Only kiln-dried or well-seasoned wood with a moisture content reading
of less than 18% is recommended. A moisture meter is a handy device to have
and is available from your supplier. As a rule-of-thumb, wood seasons at about
1” (25mm) per year, so a log split such that along its length no dimension is
greater than 3” (75mm), it would take about 3 years to dry. A dry log will
produce up to four and a half times more heat output than a freshly cut log.
Wet logs take heat to dry.
Other Solid Fuel –“Authorised” fuels include anthracite large nuts, smokeless
briquetted fuel, ie. Ancit, Phurnacite, Taybrite, Homefire Ovals suitable for
closed appliances.
Smokeless Briquetted Fuel –Only burn smokeless briquettes that are <2%
sulphur content, these will be labelled up as “HETAS approved” or “DEFRA
authorised for use in a smoke control zone”. Cheaper smokeless briquettes are
oil based and have a much higher sulphur content than the approved briquettes,

16
these are not authorised for use on this appliance. If in doubt consult your
retailer.
Unauthorised Fuels
DO NOT burn Wildfire, bituminous coal, Housecoal, household coal, petroleum
cokes or household waste. If in doubt consult your merchant or the Solid Fuel
Association.
Please note that when refuelling with solid fuel, do not pile fuel higher than 30
degrees from the front bar rearwards –over-fuelling can cause excess smoke
and produce temperatures beyond the designed rating of the appliance causing
damage to internal parts.
This stove is designed to be operated with the door closed, except for refuelling.
Not only is it unsafe to operate with the door open but the appliance efficiency
will be significantly reduced and excess smoke can occur.
This stove is designed to operate intermittently and must not be used as an
overnight burner.
Clean Burn - The Clean Air Act 1993 and Smoke Control Areas
Under the Clean Air Act local authorities may declare the whole or part of the
district of the authority to be a smoke control area. It is an offence to emit
smoke from a chimney of a building, from a furnace or from any fixed boiler if
located in a designated smoke control area. It is also an offence to acquire an
“unauthorised fuel” for use within a smoke control area unless it is used in an
“exempt” appliance (“exempted” from the controls which generally apply in the
smoke control area).
In England appliances are exempted by publication on a list by the Secretary of
State in accordance with changes made to sections 20 and 21 of the Clean Air
Act 1993 by section 15 of the Deregulation Act 2015. Similarly, in Scotland
appliances are exempted by publication on a list by Scottish Ministers under
section 50 of the Regulatory Reform (Scotland) Act 2014. In Northern Ireland
appliances are exempted by publication on a list by the Department of
Agriculture, Environment and Rural Affairs under Section 16 of the
Environmental Better regulation Act (Northern Ireland) 2016. In Wales
appliances are exempted by regulations made by Welsh Ministers.

17
This stove has been recommended as suitable for use in smoke control areas
when burning dry wood and the “authorised” smoke free solid fuels.
The “authorised” solid fuels you are permitted to burn in a smoke control zone
include: anthracite (this is naturally occurring smokeless fuel and is the test fuel
normally used and recommended), Ecoal 50, Homefire, Homefire ovals,
Phurnacite, Taybrite and Multiheat.
Refuelling Onto a Low Fire Bed
If the fire bed is not sufficient to light a new fuel charge, excessive smoke
emission can occur. Refuelling must be carried out onto a bed of glowing
embers and ash such that the new fuel ignites in a reasonable period. If there
are too few embers in the fire bed, add kindling to prevent excessive smoke.
Fuel overloading
The maximum amount of fuel specified in this manual should not be exceeded,
overloading can cause excess smoke.
Operation with door left open
Operation with the door open can cause excess smoke. The appliance must not
be operated with the appliance door left open except as directed in the
instructions.
Dampers left open
Operation with the air controls or appliance dampers open can cause excess
smoke. The appliance must not be operated with air controls, appliance
dampers or door left open except as directed in the instructions.
GENERAL MAINTENANCE (only ever carry out maintenance when the stove is cold).
The following elements of maintenance may be carried out by the householder.
Any structural repairs, e.g. panel, collar or stove pipe replacement must be
carried out by a suitably qualified installer.
Baffle Plate Removal and Replacement
Note the position before removal. To remove baffle plate, firmly push the baffle
plate upwards then bring forwards so that the back edge of the baffle plate
drops down from the rear fire brick that it was resting upon. The plate can now
be withdrawn through the open doorway of the stove.

18
To replace, place the baffle plate inside the stove in the correct alignment.
Angle the plate so that the front edge is higher than the back edge and lift high
into the stove so that the front edge locates on the steel ledge at the top of the
stove and the back edge of the plate can be re-positioned on top of the rear fire
brick.
Sweeping the Chimney
Your chimney should be cleaned each year before starting to use your stove for
the winter. Birds may have nested in the chimney or the masonry may have
cracked. Both chimney and flue pipe must be swept at least once a year. It is
recommended that you have your chimney swept every six months. It may be
necessary to sweep more frequently when damp wood is burnt regularly.
The chimney can be swept through your stove with the baffle plate removed. It
is advisable to remove the bricks too in order to avoid accidental damage.
Inner Grate Removal and Replacement
Remove the ash pan and detach the riddling arm from the underside of the
circular inner grate. Lift the inner grate vertically and manoeuvre it out of the
stove. When replacing, ensure the riddling arm is re-connected to the inner
grate.
Outer Grate Removal and Replacement
Remove all the bricks and the inner grate. Lift the outer grate up at an angle left
higher than right and manoeuvre the grate out left side first.
Stove Body
The stove is finished with a heat-resistant paint and this can be cleaned with a
soft brush. Do not clean whilst the stove is hot –wait until it has cooled down.
The finish can be renovated with stove paint available from your supplier.
Glass Panels
Clean the glass panels when cool with stove glass cleaner. Highly abrasive
substances should be avoided as these can scratch the glass and make
subsequent cleaning more difficult. Wet logs on heated glass, a badly aimed
poker or heavy slamming of doors could crack the glass panels. The glass will
not fracture from heat.

19
Should a glass panel require replacement, then remove the four screws and clips
retaining the glass frame, carefully remove the broken glass and replace the
panel with the correct stove glass from your supplier. Ensure you use new glass
fibre seal around its edge, and use the steel frame, clips and screws to retain it
in position.
Seasonal Maintenance
If your stove is be unused for any length of time, e.g. summer months, then it is
recommended that it is cleaned out thoroughly. Air slides should be lightly oiled
with WD40 or similar and left partially open to allow air circulation. Regular
monitoring of the inside components will identify condensation or water ingress.
If these problems occur, then your stove needs to be dried and the cause of the
problem rectified. After a shut-down, and before reuse, the appliance should be
cleaned again and the chimney swept, it is essential to have the chimney swept
at least once annually and it is recommended that it is swept twice a year.
Safety Notes and Troubleshooting
IT IS ESSENTIAL AND REQUIRED BY BUILDING REGULATIONS THAT A CO ALARM
IS INSTALLED IN THE SAME ROOM AS THIS APPLIANCE.
Fires Can Be Dangerous
Always use a fire guard to BS 8423:2002, Fireguards for Use With Solid Fuel
Appliances, in the presence of children, the elderly or the infirm. Inform all
persons of the dangers of high temperatures during operation of appliance
including the stove pipe.
Do not use this stove as an overnight burner, when finished for the evening,
leave the air controls open to allow the remainder of the fuel to burn out.
Use the glove provided to open the door and never empty the ash pan when it is
hot.
Do Not Over-Fire
It is possible to fire the stove beyond its design capacity, this could damage the
stove, so watch for signs of over-firing –if any part of the stove starts to glow

20
red, the fire is in an over fire situation, and the controls should be adjusted
accordingly. Never leave the stove unattended for long periods without
adjusting the controls to a safe setting –careful air supply control should be
exercised at all times and only add the recommended quantity of fuels.
Smoke and Fumes Entering the Room
When properly installed and operated, this appliance will not emit fumes into
the room. Occasional fumes from de-ashing and refuelling may occur and is
normal. Persistent fume emission with closed doors must not be tolerated.
If fume emission does persist, then the following immediate action should be
taken:
1. Evacuate the room, opening doors and windows on your exit to
ventilate the room.
2. Let the fire go out, or eject and safely dispose of fuel from the appliance.
3. Check for a flue blockage and clean if required.
Do not attempt to relight the fire until the cause has been identified and
corrected. If necessary, seek professional advice.
These situations are very dangerous and must NOT be tolerated. A list of
Qualified Engineers is available from
UK Solid Fuel Association R. o. I.
7 Swanwick Court Irish National Fireplace Organisation
Alfreton 162 Chapel Street
Derbyshire Dublin
DE55 7AS Ireland
Tel. [phone] Tel. [phone]
Chimney Fire
Identified by loud roaring sounds, dense smoke and sparks exiting chimney.
Shut down all air supply to stove by closing air vents, ensure the stove door fully
closed, call the Fire Brigade immediately. Regular chimney maintenance will
prevent chimney fires. Seek advice from a qualified chimney sweep. Chimneys
must be checked at least annually or more often when poor quality fuels that
are not recommended are burnt