Caple CM465 User manual

Sense Coffee Machine
Instruction manual
CM465, CM465SS
& CM465GM
Contact Caple on 0117 938 7420 for spare parts or www.caple.co.uk

Instruction manual CM465 / CM465SS / CM465GM2Please keep this instruction manual for future reference
CONTENTS
Introduction 3
Product Overview 9
Control Panel 10
Preparation 11
Operation 13
Using Menu Options 23
Water Hardness 24
Setting The Coffee Temperature 25
Setting The Switch-Off Time 25
Carrying Out The Descaling 26
Statistics 28
Resetting Settings 28
Setting The Clock 29
Cleaning 31
Messages 36
Troubleshooting 38
Installation Instructions 40
Caple Contact Details 44

3
Please keep this instruction manual for future reference Instruction manual CM465 / CM465SS / CM465GM
INTRODUCTION
This coffee machine will make delicious cups of coffee, espresso and cappuccino. You can
customise the settings of the machine to suit your personal preferences and tastes.
Coffee has been used in the factory to test the appliance and it is therefore completely normal
that there are traces of coffee in the mill. This appliance is however guaranteed to be new. First
read the user instructions carefully and completely before starting to use the appliance, and keep
them carefully for future reference.
PREVENTATIVE MAINTENANCE
Your coffee machine requires preventative maintenance. To guarantee that the coffee machine
works well and reliably, we recommend having the machine serviced once every 2 to 3 years
(after a maximum 8,000 cups).
Servicing of your coffee machine is chargeable, and can be booked via email [e-mail]
or telephone [phone].
WARNING:
-Designated use: this appliance is designed and made
to prepare coffee and milk based beverages and hot
water. Any other use is considered improper and thus
dangerous. The manufacturer is not liable for damage
deriving from improper use of the appliance.
-The surface of the heating element remains hot after use
and the outside of the appliance may retain the heat for
several minutes depending on use.
-CAUTION: To prevent damage to the appliance do not
use alkaline cleaning agents when cleaning, use a soft
cloth and a mild detergent

Instruction manual CM465 / CM465SS / CM465GM4Please keep this instruction manual for future reference
-WARNING: Models with glass surfaces: do not use the
appliance if the surface is cracked.
-The appliance and its accessible parts become hot during
use. Care should be taken to avoid touching heating
elements.
-The appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
-Children should be supervised to ensure that they do not
play with the appliance.
-Cleaning and user maintenance shall not be made by
children without supervision.
-Never clean by immersing the appliance in water.
-This appliance is intended to be used in household and
similar applications such as:
-Staff kitchen areas in shops, offices and other working
environments.
-Farm Houses.
-Appliances with removable cord: avoid splashes of water
on the power cord connector or socket at the back of the
appliance.
-Clean all the components thoroughly, taking particular
care with parts in contact with the coffee and milk.

5
Please keep this instruction manual for future reference Instruction manual CM465 / CM465SS / CM465GM
-By clients in hotels, motels and other residential type
environments.
-Bed and breakfast type environments.
-If the plug or power cable is damaged, it must be
replaced by customer services only to avoid all risk.
-This appliance can be used by children aged from 8
years and above if they have been given supervision or
instruction concerning use of the appliance in a safe way
and if they understand the hazard involved. Cleaning
and user maintenance shall not be made by children
unless they are older than 8 and supervised. Keep the
appliance and its cord out of the reach of children aged
less than 8 years.
-Appliances can be used by persons with reduced
physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given
supervision or instruction concerning use of the
appliance in a safe way and understand the hazards
involved.
-Children shall not play with the appliance.
-When not in use and before cleaning, always unplug the
appliance.
-This appliance is intended for domestic use only (around
3000 cups a year). Any other use is considered improper
and in that case no guarantee will be given.
-Use it with care to avoid scalds from the water and
steam jets or through incorrect use.

Instruction manual CM465 / CM465SS / CM465GM6Please keep this instruction manual for future reference
-Do not lean or hang on the machine when it has come
out of the cabinet and do not place heavy or unstable
objects on the machine.
-Surfaces marked with this symbol become hot during
use.
-This appliance can be installed over a built-in oven if the
latter is fitted with a cooling fan at the rear (maximum
microwave power: 3kW).
-The manufacturer is not liable for damage caused by
improper, incorrect or unreasonable use of the appliance.
-When using the appliance, do not touch the hot surfaces.
Use the knobs or handles.
-In case of failures, make sure the appliance is not
connected to the mains power supply. Turn the main
power switch on the right side (behind the front panel)
to 0. Refer to our service department for repairs.
-Only ask for original spare parts to be used. Failure
to respect the above could reduce the safety of the
appliance.
-Do not put objects containing liquids, inflammable or
corrosive materials on the machine.
-Use the accessories holder to contain coffee accessories
(for example coffee beans).
-Never touch the appliance with damp hands.
-Unplug directly from the plug only.

7
Please keep this instruction manual for future reference Instruction manual CM465 / CM465SS / CM465GM
-Never pull the power cable as you could damage it.
-To disconnect the appliance completely, place the
main switch on the side of the appliance in the 0 (off)
position.
-Your appliance is produced in accordance with all
applicable local and international standards and
regulations.
-Maintenance and repair work must be made only
by authorised Caple service technicians. Installation
and repair work that is carried out by unauthorised
technicians may endanger you.
-It is dangerous to alter or modify the specifications of
the appliance in any way.
-Prior to installation, ensure that the local distribution
conditions (electricity voltage and frequency) and the
requirements of the appliance are compatible.
The requirements for this appliance are stated on the
rating label.
-This appliance is designed only for cooking food and is
intended for indoor use.minimum temperature of 120°C.

Instruction manual CM465 / CM465SS / CM465GM8Please keep this instruction manual for future reference
ENVIRONMENTAL PROTECTION
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.
This appliance is marked according to the European directive on Waste Electrical and Electronic
Equipment (WEEE). By ensuring this product is disposed of correctly, you will help prevent
potential negative consequences for the environment and human health, which could otherwise
be caused by inappropriate waste handling of this product. The symbol on the product indicates
that this product may not be treated as household waste. Instead, it shall be handed over to the
applicable collection point for the recycling of electrical and electronic equipment. Disposal must
be carried out in accordance with local environmental regulations for waste disposal.
For more detailed information about treatment, recovery and recycling of this product, please
contact your local council, your household waste disposal service or the retailer where you
purchased the product.
CE DECLARATIONS OF CONFORMITY
This appliance has been manufactured to the strictest standards and complies with all applicable
legislation, Low Voltage Directive (LVD) and Electromagnetic Compatibility (EMC).
This appliance also conforms to all applicable UK & EU legislation relating to Materials and articles
intending to come into contact with food.
UKCA DECLARATIONS OF CONFORMITY
This appliance has been manufactured to the strictest standards and complies with all
applicable legislation.
WARRANTY
Your new appliance is covered by warranty. The warranty card is enclosed - if it is missing, you
must provide the following information to your retailer in order to receive a replacement: date
of purchase, model and serial number (placed on the inside of the appliance storage drawer).
Registration can also be completed online by visiting www.caple.co.uk.
Ensure you keep your warranty card safe, you may need to show it to Caple Service together
withproof of purchase.If you fail to show your warranty card you will incur all repair charges.
Spare parts are only available from Caple Service and spare parts authorised centres.

9
Please keep this instruction manual for future reference Instruction manual CM465 / CM465SS / CM465GM
EN 5
Product overview
A. Main switch
(Aa) - On / Off button
B. Handles
C. Nozzle
D. Water tank (removable)
E. Cup tray
F. Drip tray grill (removable)
G. Service door
H. Height adjustable coffee dispenser
I. Control panel
J. Coffee bean holder cover
K. Ground coffee chute cover
L. Brewing unit
M. Power cable
N. Milk container:
N1. Cover (removable)
N2. Slider CAFFELATTE/CAPPUCCINO
(removable)
N3. CLEAN button
N4. Milk dispenser pipe (removable)
N5. Suction pipe (removable)
O. Hot water nozzle (removable)
P. Measuring spoon for preground coffee
Q. Waste coffee container (can be taken out)
R. Knob for setting the grind level
S. Coffee bean container
T. Place for the measuring spoon
U. Filling chute for preground coffee
V. Coffee guide
W. Place for accessories (left and right)
X. IEC Connector B Aa
Aa
B
V
LQ
E
G
F H D
CY
P
I
1CAPPUCCINO
2CAFFELA TTE
N
N1
O
N2
N3
N4
N5
x
EN 5
Product overview
A. Main switch
(Aa) - On / Off button
B. Handles
C. Nozzle
D. Water tank (removable)
E. Cup tray
F. Drip tray grill (removable)
G. Service door
H. Height adjustable coffee dispenser
I. Control panel
J. Coffee bean holder cover
K. Ground coffee chute cover
L. Brewing unit
M. Power cable
N. Milk container:
N1. Cover (removable)
N2. Slider CAFFELATTE/CAPPUCCINO
(removable)
N3. CLEAN button
N4. Milk dispenser pipe (removable)
N5. Suction pipe (removable)
O. Hot water nozzle (removable)
P. Measuring spoon for preground coffee
Q. Waste coffee container (can be taken out)
R. Knob for setting the grind level
S. Coffee bean container
T. Place for the measuring spoon
U. Filling chute for preground coffee
V. Coffee guide
W. Place for accessories (left and right)
X. IEC Connector B Aa
Aa
B
V
LQ
E
G
F H D
CY
P
I
1CAPPUCCINO
2CAFFELA TTE
N
N1
O
N2
N3
N4
N5
x
A. Main switch
(Aa) - On / Off button
B. Handles
C. Nozzle
D. Water tank (removable)
E. Cup tray
F. Drip tray grill (removable)
G. Service door
H. Height adjustable coffee dispenser
I. Control panel
J. Coffee bean holder cover
K. Ground coffee chute cover
L. Brewing unit
M. Power cable
N. Milk container:
N1. Cover (removable)
N2. Slider CAFFELATTE/CAPPUCCINO
(removable)
N3. CLEAN button
N4. Milk dispenser pipe (removable)
N5. Suction pipe (removable)
O. Hot water nozzle (removable)
P. Measuring spoon for preground coffee
Q. Waste coffee container
(can be taken out)
R. Knob for setting the grind level
S. Coffee bean container
T. Place for the measuring spoon
U. Filling chute for preground coffee
V. Coffee guide
W. Place for accessories (left and right)
X. IEC Connector
Y. LED
PRODUCT OVERVIEW

Instruction manual CM465 / CM465SS / CM465GM10 Please keep this instruction manual for future reference
MENU
EXIT OK
CONTROL PANEL
1. ‘MENU’ to activate or deactivate menu
2. ‘RETURN’ to exit the selected mode
3. ‘Rinse’
4. ‘SCROLL’ to scroll forwards through the menu and display
5. ‘COFFEE STRENGTH’ to select strength or preground
6. ‘SCROLL’ to scroll backwards through the menu and display
7. Touch key to select the type/quantity of coffee (espresso, smallcup,
medium cup, large cup, mug)
8. ‘OK’ to confirm the selected function
9. Touch key ‘One cup of coffee’
10. Touch key ‘Two cups of coffee’
11. Touch key ‘Cappuccino’
12. Touch key ‘Hot water deliver’
1
2
3
4
5
6
7
8
910 11 12

11
Please keep this instruction manual for future reference Instruction manual CM465 / CM465SS / CM465GM
PREPARATION
The first time you switch on the appliance with the main switch (see ‘A’
on the ‘Product overview’ section) and every time that it is plugged in,
the appliance executes a “SELF-DIAGNOSIS” action. Then the appliance
switches off.
To turn it on, press the On/off button (Aa/see fig. 1) on the left side
underneath the control panel.
› Coffee has been used to factory test the appliance and it is
therefore completely normal for there to be traces of coffee in
the mill.
› Customise water hardness as soon as possible following the
instructions in the “Setting water hardness” section.
1. Connect the appliance to the mains supply.
2. Switch on the appliance with the main switch
(see ‘A’ on ‘Product overview’.
3. Start the appliance with the on/off button (see ‘Aa’).
4. Set the required language.
› Choose the required language using the ‘scroll’ touch keys (5
and 7). When the message “PRESS OK TO CHOOSE ENGLISH”
is displayed, press and hold the touch key ‘Ok’ (9). If you set
the wrong language, follow the instructions in the “Setting
the language” section. If your language is not available, select
one from those displayed. The instructions refer to the English
version. Then follow the instructions displayed:
5. After 5 seconds, the appliance displays “ENGLISH INSTALLED”.
› Extract the water tank, rinse and fill with fresh water without
exceeding the MAX line.
› Replace and push as far as it will go.
EN 10
USE
Preparation
The first time you switch on the appliance with the main switch (see ‘A’
on the 'Product overview' section) and every time that it is plugged in,
the appliance executes a “SELF-DIAGNOSIS” action. Then the
appliance switches off.
To turn it on, press the On/off button (Aa/see fig. 1) on the left side
underneath the control panel.
• Coffee has been used to factory test the appliance and it is therefore
completely normal for there to be traces of coffee in the mill.
• Customise water hardness as soon as possible following the
instructions in the “Setting water hardness” section.
1. Connect the appliance to the mains supply.
2. Switch on the appliance with the main switch (see ‘A’ on 'Product
overview'.
3. Start the appliance with the on/off button (see ‘Aa’).
4. Set the required language.
•Choose the required language using the ‘scroll’ touch keys (5
and 7). When the message “PRESS OK TO CHOOSE ENGLISH”
is displayed, press and hold the touch key ‘Ok’ (9). If you set the
wrong language, follow the instructions in the “Setting the
language” section. If your language is not available, select
one from those displayed. The instructions refer to the English
version. Then follow the instructions displayed:
5. After 5 seconds, the appliance displays “ENGLISH INSTALLED”.
•Extract the water tank, rinse and fill with fresh water without
exceeding the MAX line.
•Replace and push as far as it will go.
6. Place a cup under the hot water spout (If the hot water spout is not
inserted, the appliance displays “INSERT WATER SPOUT”.
The appliance displays: “HOT WATER PRESS OK”. Press the touch key
‘OK’ (9) and after a few seconds a little water comes out of the spout.
7. The machine now displays “TURNING OFF...PLEASE WAIT” and
goes off.
8. Extract the appliance by pulling it out using the handles.
Open the lid and fill the container with coffee beans, then close the
lid and push the appliance in. The coffee maker is now ready for
normal use.
Only fill the water tank with cold water. Never use other liquids
such as mineral water or milk.
2
1
Aa
5
279
FFiigg..11
UUSSEE OOUURR AARRTTWWOORRKK
EN 10
USE
Preparation
The first time you switch on the appliance with the main switch (see ‘A’
on the 'Product overview' section) and every time that it is plugged in,
the appliance executes a “SELF-DIAGNOSIS” action. Then the
appliance switches off.
To turn it on, press the On/off button (Aa/see fig. 1) on the left side
underneath the control panel.
• Coffee has been used to factory test the appliance and it is therefore
completely normal for there to be traces of coffee in the mill.
• Customise water hardness as soon as possible following the
instructions in the “Setting water hardness” section.
1. Connect the appliance to the mains supply.
2. Switch on the appliance with the main switch (see ‘A’ on 'Product
overview'.
3. Start the appliance with the on/off button (see ‘Aa’).
4. Set the required language.
•Choose the required language using the ‘scroll’ touch keys (5
and 7). When the message “PRESS OK TO CHOOSE ENGLISH”
is displayed, press and hold the touch key ‘Ok’ (9). If you set the
wrong language, follow the instructions in the “Setting the
language” section. If your language is not available, select
one from those displayed. The instructions refer to the English
version. Then follow the instructions displayed:
5. After 5 seconds, the appliance displays “ENGLISH INSTALLED”.
•Extract the water tank, rinse and fill with fresh water without
exceeding the MAX line.
•Replace and push as far as it will go.
6. Place a cup under the hot water spout (If the hot water spout is not
inserted, the appliance displays “INSERT WATER SPOUT”.
The appliance displays: “HOT WATER PRESS OK”. Press the touch key
‘OK’ (9) and after a few seconds a little water comes out of the spout.
7. The machine now displays “TURNING OFF...PLEASE WAIT” and
goes off.
8. Extract the appliance by pulling it out using the handles.
Open the lid and fill the container with coffee beans, then close the
lid and push the appliance in. The coffee maker is now ready for
normal use.
Only fill the water tank with cold water. Never use other liquids
such as mineral water or milk.
2
1
Aa
5
279
F
F
i
i
g
g
.
.
1
1
UUSSEE OOUURR AARRTTWWOORRKK
MENU
EXIT OK
2
5 7 9

Instruction manual CM465 / CM465SS / CM465GM12 Please keep this instruction manual for future reference
6. Place a cup under the hot water spout (If the hot water spout is not inserted, the appliance
displays “INSERT WATER SPOUT”.
The appliance displays: “HOT WATER PRESS OK”.
Press the touch key ‘OK’ (9) and after a few seconds a little water comes out of the spout.
7. The machine now displays “TURNING OFF...PLEASE WAIT” and goes off.
8. Extract the appliance by pulling it out using the handles. Open the lid and fill the container
with coffee beans, then close the lid and push the appliance in. The coffee maker is now ready
for normal use.
Only fill the water tank with cold water. Never use other liquids such as mineral
water or milk.
WARNING:
To prevent malfunctions, never fill with ground coffee, frozen or caramelised coffee beans or
anything else that could damage the appliance.
TIPS:
› When using the appliance for the first time, you need to make 4-5 cups of coffee and 4-5
cappuccinos before the appliance gives satisfactory results.
› Each time you turn the coffee maker on by the main switch (A), it performs a “SELF
DIAGNOSIS” cycle and then goes off. To turn it on again, press the
On/off button (Aa).

13
Please keep this instruction manual for future reference Instruction manual CM465 / CM465SS / CM465GM
OPERATION
MENU
EXIT OK
6 8
MENU
EXIT
OK
10 11
PREPARING COFFEE (USING COFFEE BEANS)
› The appliance is preset to make coffee with a normal taste. You
can also choose coffee with an extra mild, mild, standard, strong
or extra-strong taste. There is also a pre-ground coffee option.
› To choose the required taste, continually press the touch key
‘Coffee strength’ (6) until the required coffee taste is displayed.
1. Place 1 cup under the spouts to make 1 coffee or 2 cups for
2 coffees.
2. Lower the spouts as near as possible to the cup for a
creamier coffee.
3. Press the ‘type of coffee’ touch key (8) to select the type of coffee:
› ESPRESSO CUP
› SMALL CUP
› MEDIUM CUP
› LARGE CUP
› MUG
4. Press the ‘deliver one cup of coffee’ touch key (10) if you want to
make one coffee and the ‘two cup of coffee’ touch key (11) if you
want to make two coffees.
› The appliance now grinds the beans and starts delivering the
coffee into the cup.
› Once the set amount of coffee has been delivered, the machine
stops delivery automatically and expels the exhausted waste
coffee into the waste coffee container.
› After a few seconds, the appliance is ready for use again.
› To turn the appliance off, press the ‘On-off’ button (Aa / see
page 5). Before going off, the appliance performs an automatic
rinse cycle. Take care to avoid scalds.
EN 11
WARNING: To prevent malfunctions, never fill with ground coffee, frozen or caramelised
coffee beans or anything else that could damage the appliance.
• When using the appliance for the first time, you need to make 4-5 cups of coffee and 4-5
cappuccinos before the appliance gives satisfactory results.
• Each time you turn the coffee maker on by the main switch (A), it performs a “SELF-
DIAGNOSIS” cycle and then goes off. To turn it on again, press the On/off button (Aa).
Operation
Preparing coffee (using coffee beans)
• The appliance is preset to make coffee with a normal taste. You can
also choose coffee with an extra mild, mild, standard, strong or
extra-strong taste. There is also a pre-ground coffee option.
• To choose the required taste, continually press the touch key
‘Coffee strength’ (6) until the required coffee taste is displayed.
1. Place 1 cup under the spouts to make 1 coffee or 2 cups for
2 coffees.
2. Lower the spouts as near as possible to the cup for a creamier
coffee.
3. Press the ‘type of coffee’ touch key (8) to select the type of coffee:
•ESPRESSO CUP
•SMALL CUP
•MEDIUM CUP
•LARGE CUP
•MUG
4. Press the ‘one cup of coffee deliver’ touch key (10) if you want to
make one coffee and the ‘two cup of coffee deliver’ touch key (11)
if you want to make two coffees.
• The appliance now grinds the beans and starts delivering the coffee
into the cup.
• Once the set amount of coffee has been delivered, the machine
stops delivery automatically and expels the exhausted waste coffee
into the waste coffee container.
USE
6 8
10 11
TTiippss
RREEPPLLAACCEE
WWIITTHH OOUURR
AARRTTWWOORRKK
EN 12
USE
• After a few seconds, the appliance is ready for use again.
• To turn the appliance off, press the ‘On-off’ button (Aa / see page 5).
Before going off, the appliance performs an automatic rinse cycle.
Take care to avoid scalds.
•If the coffee only comes out in drips or not at all, the knob for setting
the grind level must be turned by one position clockwise (see
“Setting the grind level” ). Turn one click at a time until the coffee is
delivered satisfactorily.
•If the coffee comes out too fast and the cream does not meet your
taste, turn the knob by one position anti-clockwise). Make sure that
you do not turn the knob for setting the grind level too far, as coffee
may come out in drips when dispensing 2 cups.
Tips to make hotter coffee
• After 3 minutes since you last made coffee, you can preheat the
brewing unit by using the menu setting “RINSING (see Rinsing). Run
off the water into the underlying drip tray or alternatively use this
water to fi ll (and then empty) the cup to be used for the coffee.
• Do not use cups that are too thick, as they will absorb too much
heat.
• You can stop the coffee from dispensing by pressing the ‘One cup of
coffee deliver’ touch key (10) or ‘Two cup of coffee deliver’ touch key
(11) again, or by selecting “ESPRESSO CUP” with the ‘Type/quantity
of coffee’ touch key (8).
• After the coffee has finished dispensing (the progress bar reaches
100%), you can increase the amount of coffee by pressing and
holding the ‘One cup of coffee’ touch key until the desired amount of
coffee is reached.
• When the display shows the message “FILL TANK!”, you must fill the
tank, otherwise the appliance cannot make any coffee.
It is normal that there is some water left in the water tank when the
message is displayed.
• Every 14 single coffees (or 7 doubles) the appliance displays
“EMPTY WASTE COFFEE CONTAINER”. This means that the waste
coffee container is full and must be emptied and cleaned.

Instruction manual CM465 / CM465SS / CM465GM14 Please keep this instruction manual for future reference
› If the coffee only comes out in drips or not at all, the knob for setting the grind level
must be turned by one position clockwise (see “Setting the grind level” ). Turn one click
at a time until the coffee is delivered satisfactorily.
› If the coffee comes out too fast and the cream does not meet your taste, turn the knob
by one position anti-clockwise). Make sure that you do not turn the knob for setting the
grind level too far, as coffee may come out in drips when dispensing 2 cups.
TIPS TO MAKE HOTTER COFFEE:
› 3 minutes after your last made coffee, you can preheat the brewing unit by using the
menu setting “RINSING (see Rinsing). Run off the water into the underlying drip tray or
alternatively use this water to fill (and then empty) the cup to be used for the coffee.
› Do not use cups that are too thick, as they will absorb too much heat.
› You can stop the coffee from dispensing by pressing the ‘deliver one cup of coffee’ touch key
(10) or ‘Two cup of coffee’ touch key (11) again, or by selecting “ESPRESSO CUP” with the
‘Type/quantity of coffee’ touch key (8).
› After the coffee has finished dispensing (the progress bar reaches 100%), you can increase
the amount of coffee by pressing and holding the ‘One cup of coffee’ touch key until the
desired amount of coffee is reached.
› When the display shows the message “FILL TANK!”, you must fill the tank, otherwise the
appliance cannot make any coffee. It is normal that there is some water left in the water
tank when the message is displayed.
› Every 14 single coffees (or 7 doubles) the appliance displays “EMPTY WASTE COFFEE
CONTAINER”. This means that the waste coffee container is full and must be emptied
and cleaned.
EN 13
USE
• The appliance counts the number of coffees made. As long as the
waste coffee container is not cleaned, this message remains in
place and the coffee machine cannot make any coffee. To clean,
open the service door at the front by pulling the coffee spout,
remove the drip tray, empty it and clean it.
Important!
Always completely extract the drip tray, to avoid that it falls when
removing the grounds container. Empty the grounds container and
clean thoroughly, making sure all residues deposited on the bottom
are removed.
Every time you pull the drip tray out, the waste coffee container
must also be emptied, even if it is not completely full. If this
process is not carried out, the waste coffee container may overfill
when coffee is made and the machine may get blocked.
Never remove the water tank when the appliance is dispensing
coffee. Otherwise, the appliance will not be able to make the
coffee. If the appliance malfunctions, do not contact Caple service
straight away, first look at the troubleshooting guide. If this does
not help, contact Caple customer service.
Changing the quantity of coffee
The appliance is factory preset to automatically deliver the following
quantities of coffee:
• ESPRESSO CUP;
• SMALL CUP;
• MEDIUM CUP;
• LARGE CUP;
• MUG.
To change these quantities, proceed as follows:
1. Press the touch key ‘MENU‘ (2) and press the ‘Scroll’ touch keys
(5 and 7) until the menu option “PROGRAM COFFEE” appears.
Confirm the menu option with the touch key ‘OK’ (9).
EN 13
USE
• The appliance counts the number of coffees made. As long as the
waste coffee container is not cleaned, this message remains in
place and the coffee machine cannot make any coffee. To clean,
open the service door at the front by pulling the coffee spout,
remove the drip tray, empty it and clean it.
Important!
Always completely extract the drip tray, to avoid that it falls when
removing the grounds container. Empty the grounds container and
clean thoroughly, making sure all residues deposited on the bottom
are removed.
Every time you pull the drip tray out, the waste coffee container
must also be emptied, even if it is not completely full. If this
process is not carried out, the waste coffee container may overfill
when coffee is made and the machine may get blocked.
Never remove the water tank when the appliance is dispensing
coffee. Otherwise, the appliance will not be able to make the
coffee. If the appliance malfunctions, do not contact Caple service
straight away, first look at the troubleshooting guide. If this does
not help, contact Caple customer service.
Changing the quantity of coffee
The appliance is factory preset to automatically deliver the following
quantities of coffee:
• ESPRESSO CUP;
• SMALL CUP;
• MEDIUM CUP;
• LARGE CUP;
• MUG.
To change these quantities, proceed as follows:
1. Press the touch key ‘MENU‘ (2) and press the ‘Scroll’ touch keys
(5 and 7) until the menu option “PROGRAM COFFEE” appears.
Confirm the menu option with the touch key ‘OK’ (9).
› The appliance counts the number of coffees
made. As long as the waste coffee container is
not cleaned, this message remains in place and
the coffee machine cannot make any coffee.
To clean, open the service door at the front by
pulling the coffee spout, remove the drip tray,
empty it and clean it.

15
Please keep this instruction manual for future reference Instruction manual CM465 / CM465SS / CM465GM
IMPORTANT
Always completely extract the drip tray, to avoid it falling when removing the grounds container.
Empty the grounds container and clean thoroughly, making sure all residues deposited on the
bottom are removed.
Every time you pull the drip tray out, the waste coffee container must also be emptied, even if it is
not completely full. If this process is not carried out, the waste coffee container may overfill when
coffee is made and the machine may get blocked.
Never remove the water tank when the appliance is dispensing coffee. Otherwise, the appliance
will not be able to make the coffee. If the appliance malfunctions, do not contact Caple service
straight away, first look at the troubleshooting guide. If this does not help, contact Caple
customer service.
CHANGING THE QUANTITY OF COFFEE:
The appliance is factory preset to automatically deliver the following quantities of coffee:
› ESPRESSO CUP;
› SMALL CUP;
› MEDIUM CUP;
› LARGE CUP;
› MUG.
TO CHANGE THESE QUANTITIES, PROCEED AS FOLLOWS:
1. Press the touch key ‘MENU‘ (2) and press the ‘Scroll’ touch keys (5 and 7) until the menu
option “PROGRAM COFFEE” appears. Confirm the menu option with the touch key ‘OK’ (9).
2. Select the cup size you want to change with the scrolling touch keys (5 and 7). When the
desired cup size is displayed, confirm it with the touch key ‘OK’ (9).
3. A bar appears on the display, which can be made bigger or smaller; this represents the cup
filling quantity. A different quantity can be selected using the scrolling touch keys (5 and 7) in
10 steps. A full bar indicates that the maximum cup filling quantity of 220ml is selected.
4. Select the desired cup filling quantity and confirm it with the touch key ‘OK’ (9) to programme
this setting. If you don’t press the touch key ‘OK’ (9), the appliance automatically returns
to the coffee mode after 120 seconds without saving. After programming the display
automatically jumps back to the menu option for setting the filling quantity. To go back to the
coffee mode immediately, press the touch key ‘MENU’ (2) twice or wait about 120 seconds
until the appliance automatically returns to the coffee mode.

Instruction manual CM465 / CM465SS / CM465GM16 Please keep this instruction manual for future reference
EN 14
USE
2. Select the cup size you want to change with the scrolling touch keys
(5 and 7). When the desired cup size is displayed, confirm it with the
touch key ‘OK’ (9).
3. A bar appears on the display, which can be made bigger or smaller;
this represents the cup filling quantity. A different quantity can be
selected using the scrolling touch keys (5 and 7) in 10 steps. A full
bar indicates that the maximum cup filling quantity of 220ml is
selected.
4. Select the desired cup filling quantity and confirm it with the touch
key ‘OK’ (9) to program this setting. If you don’t press the touch key
‘OK’ (9), the appliance automatically returns to the coffee mode after
120 seconds without saving.
After programming the display automatically jumps back to the
menu option for setting the filling quantity. To go back to the coffee
mode immediately, press the touch key ‘MENU’ (2) twice or wait
about 120 seconds until the appliance automatically returns to the
coffee mode.
Setting the grind level
If coffee is dispensed too quickly or too slowly (in drips), you can
change the grind level.
Only change the grind level during the milling process. Otherwise,
the coffee machine may be damaged.
1. Turn anti-clockwise to obtain finer ground coffee, slower delivery
and a creamier appearance.
2. Turn clockwise for coarser ground coffee and faster delivery (not a
drop at a time).
The adjustment will be evident after at least 2 cups of coffee are made.
Preparing espresso coffee using ground coffee
1. Press the ‘Coffee strength’ touch key (6) and select
“PRE-GROUND”.
2. Extract the machine by pulling it outwards using the handles.
If coffee is dispensed too quickly or too slowly (in drips), you can change
the grind level.
Only change the grind level during the milling process.
Otherwise, the coffee machine may be damaged.
1. Turn anti-clockwise to obtain finer ground coffee, slower delivery and
a creamier appearance.
2. Turn clockwise for coarser ground coffee and faster delivery (not a
drop at a time).
The adjustment will be evident after at least 2 cups of coffee are made.
PREPARING ESPRESSO COFFEE USING GROUND COFFEE
1. Press the ‘Coffee strength’ touch key (6) and select “PRE-GROUND”.
2. Extract the machine by pulling it outwards using the handles.
3. Lift the central lid, place one measure of preground coffee in the
funnel push the appliance back and proceed as described in the
section “Making coffee using coffee beans”. You can make just one
coffee at a time by pressing the ‘One cup deliver’ touch key (10).
4. After using the machine with pre-ground coffee, to go back to making
coffee using beans, deactivate the pre-ground coffee function by
pressing the ‘Coffee strength’ touch key (6).
EN 15
USE
3. Lift the central lid, place one measure of preground coffee in the
funnel push the appliance back and proceed as described in the
section “Making coffee using coffee beans”. You can make just one
coffee at a time by pressing the ‘One cup deliver’ touch key (10).
4. After using the machine with pre-ground coffee, to go back to
making coffee using beans, deactivate the pre-ground coffee
function by pressing the ‘Coffee strength’ touch key (6).
Notes
• Never introduce pre-ground coffee when the machine is off as it
could spread through the inside of the appliance.
• Never add more than 1 measure, otherwise the appliance will not
make the coffee.
• Use the measure provided only.
• Introduce only pre-ground coffee for espresso coffee machines into
the funnel.
• If more than one measure of pre-ground coffee is used and the
funnel clogs, push the coffee down with a knife then remove and
clean the brewing unit and machine as described in the “Cleaning
the brewing unit” section.
Preparing hot water
Hot water can be used to warm up cups and to make hot drinks, such
as tea or packet soups.
Warning! Escaping hot water can lead to scalds! Only activate the
hot water nozzle when there is a receptacle underneath it.
1. Put the hot water nozzle in place.
2. Place a container underneath the hot water nozzle.
3. Press the ‘Hot water’ touch key (13).
The display shows “HOT WATER PRESS OK”.
4. Press the touch key ‘OK’ (9).
Hot water is dispensed; the display shows “HOT WATER”.
Once the programmed amount of hot water is dispensed,
dispensing stops automatically.
For a few seconds the display shows “PLEASE WAIT”. After that the
appliance is ready to make coffee again and the last selected coffee
setting appears on the display.
SETTING THE GRIND LEVEL

17
Please keep this instruction manual for future reference Instruction manual CM465 / CM465SS / CM465GM
EN 15
USE
3. Lift the central lid, place one measure of preground coffee in the
funnel push the appliance back and proceed as described in the
section “Making coffee using coffee beans”. You can make just one
coffee at a time by pressing the ‘One cup deliver’ touch key (10).
4. After using the machine with pre-ground coffee, to go back to
making coffee using beans, deactivate the pre-ground coffee
function by pressing the ‘Coffee strength’ touch key (6).
Notes
• Never introduce pre-ground coffee when the machine is off as it
could spread through the inside of the appliance.
• Never add more than 1 measure, otherwise the appliance will not
make the coffee.
• Use the measure provided only.
• Introduce only pre-ground coffee for espresso coffee machines into
the funnel.
• If more than one measure of pre-ground coffee is used and the
funnel clogs, push the coffee down with a knife then remove and
clean the brewing unit and machine as described in the “Cleaning
the brewing unit” section.
Preparing hot water
Hot water can be used to warm up cups and to make hot drinks, such
as tea or packet soups.
Warning! Escaping hot water can lead to scalds! Only activate the
hot water nozzle when there is a receptacle underneath it.
1. Put the hot water nozzle in place.
2. Place a container underneath the hot water nozzle.
3. Press the ‘Hot water’ touch key (13).
The display shows “HOT WATER PRESS OK”.
4. Press the touch key ‘OK’ (9).
Hot water is dispensed; the display shows “HOT WATER”.
Once the programmed amount of hot water is dispensed,
dispensing stops automatically.
For a few seconds the display shows “PLEASE WAIT”. After that the
appliance is ready to make coffee again and the last selected coffee
setting appears on the display.
EN 15
USE
3. Lift the central lid, place one measure of preground coffee in the
funnel push the appliance back and proceed as described in the
section “Making coffee using coffee beans”. You can make just one
coffee at a time by pressing the ‘One cup deliver’ touch key (10).
4. After using the machine with pre-ground coffee, to go back to
making coffee using beans, deactivate the pre-ground coffee
function by pressing the ‘Coffee strength’ touch key (6).
Notes
• Never introduce pre-ground coffee when the machine is off as it
could spread through the inside of the appliance.
• Never add more than 1 measure, otherwise the appliance will not
make the coffee.
• Use the measure provided only.
• Introduce only pre-ground coffee for espresso coffee machines into
the funnel.
• If more than one measure of pre-ground coffee is used and the
funnel clogs, push the coffee down with a knife then remove and
clean the brewing unit and machine as described in the “Cleaning
the brewing unit” section.
Preparing hot water
Hot water can be used to warm up cups and to make hot drinks, such
as tea or packet soups.
Warning! Escaping hot water can lead to scalds! Only activate the
hot water nozzle when there is a receptacle underneath it.
1. Put the hot water nozzle in place.
2. Place a container underneath the hot water nozzle.
3. Press the ‘Hot water’ touch key (13).
The display shows “HOT WATER PRESS OK”.
4. Press the touch key ‘OK’ (9).
Hot water is dispensed; the display shows “HOT WATER”.
Once the programmed amount of hot water is dispensed,
dispensing stops automatically.
For a few seconds the display shows “PLEASE WAIT”. After that the
appliance is ready to make coffee again and the last selected coffee
setting appears on the display.
NOTES:
1. Never introduce pre-ground coffee when the machine is off as it could
spread through the inside of the appliance.
2. Never add more than 1 measure, otherwise the appliance will not
make the coffee.
3. Use the measure provided only.
4. Introduce only pre-ground coffee for espresso coffee machines into the
funnel.
5. If more than one measure of pre-ground coffee is used and the funnel
clogs, push the coffee down with a knife then remove and clean the
brewing unit and machine as described in the “Cleaning the brewing
unit” section.
PREPARING HOT WATER
Hot water can be used to warm up cups and to make hot drinks, such as
tea or packet soups.
WARNING:
Escaping hot water can lead to scalds. Only activate the hot water nozzle
when there is a receptacle underneath it.
1. Put the hot water nozzle in place.
2. Place a container underneath the hot water nozzle.
3. Press the ‘Hot water’ touch key (13). The display shows “HOT WATER
PRESS OK”.
4. Press the touch key ‘OK’ (9).
Hot water is dispensed; the display shows “HOT WATER”.
Once the programmed amount of hot water is dispensed, dispensing
stops automatically.
For a few seconds the display shows “PLEASE WAIT”. After that the
appliance is ready to make coffee again and the last selected coffee
setting appears on the display.

Instruction manual CM465 / CM465SS / CM465GM18 Please keep this instruction manual for future reference
The machine is set by default to automatically delivery 150ml of hot
water. To change these quantities, proceed as follows:
1. Place a container underneath the water spout.
2. Press the touch key ‘MENU’(2) to enter the menu
3. Press the Scroll touch keys (5 and 7) until “PROGRAM HOT WATER”
is displayed.
4. Press the touch key ‘OK’ (9) to confirm.
5. Select the required quantity of water by pressing scroll touch keys (5
and 7). The progress bar shows the quantity of water selected.
6. Press the touch key ‘OK’ (9) to confirm (or the ‘Return’ touch key (3) to
cancel the operation.
7. Press the ‘Return’ touch key (3) to exit the menu.
8. The appliance is now reprogrammed with the new settings and
is ready.
MAKING CAPPUCCINO
The machine is set by default to automatically delivery a standard
cappuccino.
1. Select the taste of the coffee you want to use to make the cappuccino
by pressing the ‘Coffee strength’ touch key (6).
2. Remove the lid of the milk container.
3. Fill the container with about 100ml of milk for each cappuccino to be
prepared. Never exceed the MAX level (corresponding to about 750ml)
marked on the container. You should ideally use skimmed or semi
skimmed milk at refrigerator temperature (about 5°C).
4. Make sure the intake tube is correctly inserted in the rubber washer.
Then replace the milk container lid.
EN 16
USE
Changing the quantity of hot water
The machine is set by default to automatically delivery 150ml of hot
water. To change these quantities, proceed as follows:
1. Place a container underneath the water spout.
2. Press the touch key ‘MENU’(2) to enter the menu
3. Press the Scroll touch keys (5 and 7) until “PROGRAM HOT WATER”
is displayed.
4. Press the touch key ‘OK’ (9) to confirm.
5. Select the required quantity of water by pressing scroll touch keys (5
and 7). The progress bar shows the quantity of water selected.
6. Press the touch key ‘OK’ (9) to confirm (or the ‘Return’ touch key (3)
to cancel the operation.
7. Press the ‘Return’ touch key (3) to exit the menu.
8. The appliance is now reprogrammed with the new settings
and is ready.
Making cappuccino
The machine is set by default to automatically delivery a standard
cappuccino.
1. Select the taste of the coffee you want to use to make the
cappuccino by pressing the ‘Coffee strength’ touch key (6).
2. Remove the lid of the milk container.
3. Fill the container with about 100ml of milk for each cappuccino to be
prepared. Never exceed the MAX level (corresponding to about
750ml) marked on the container. You should ideally use skimmed or
semi skimmed milk at refrigerator temperature (about 5°C).
4. Make sure the intake tube is correctly inserted in the rubber washer.
Then replace the milk container lid.
5. Position the frothed milk regulator (N2) between the words
CAPPUCCINO and CAFFELATTE printed on the milk container lid.
6. The quantity of froth can be adjusted by moving the regulator
towards the word CAFFELATTE for a denser froth. Moving it towards
the word CAPPUCCINO obtains a less dense froth.
7. Remove the hot water spout and attach the milk container to the
nozzle.
8. Position the milk spout and then place a sufficiently large cup under
the coffee and milk spouts.
22
1
CHANGING THE QUANTITY OF HOT WATER

19
Please keep this instruction manual for future reference Instruction manual CM465 / CM465SS / CM465GM
5. Position the frothed milk regulator (N2) between the words
CAPPUCCINO and CAFFELATTE printed on the milk container lid.
6. The quantity of froth can be adjusted by moving the regulator
towards the word CAFFELATTE for a denser froth. Moving it towards
the word CAPPUCCINO obtains a less dense froth.
7. Remove the hot water spout and attach the milk container to the
nozzle.
8. Position the milk spout and then place a sufficiently large cup under
the coffee and milk spouts.
9. Press the ‘Cappuccino deliver’ touch key (12). “CAPPUCCINO” is
displayed and after a few seconds, frothed milk flows out of the milk
spout into the cup below (delivery stops automatically).
10. The appliance delivers coffee.
11. The cappuccino is now ready. Sweeten to taste and, if desired,
sprinkle the froth with a little cocoa powder.
NOTES:
1. While making cappuccino, the flow of frothed milk or coffee can be
interrupted by pressing the ‘Cappuccino deliver’ touch key (12).
2. If the milk in the container finishes while delivering frothed milk,
remove the container and add milk. Then re-attach it and press the
‘Cappuccino deliver’ touch key (12) to request cappuccino again.
3. To ensure the complete cleanliness and hygiene of the milk frother,
always clean the circuits in the milk container lid after making
cappuccino. “PRESS CLEAN!” flashes on the display.
› Place a recipient under the milk spout.
› Press the CLEAN button on the lid (N3) and hold down for at
least 5 seconds to start the cleaning function.
The appliance displays the message “CLEANING” above a
progressive bar. You should not release the CLEAN button until
the bar is complete indicating that cleaning is concluded.
EN 17
USE
9. Press the ‘Cappuccino deliver’ touch key (12). “CAPPUCCINO” is
displayed and after a few seconds, frothed milk flows out of the milk
spout into the cup below (delivery stops automatically).
10.The appliance delivers coffee.
11.The cappuccino is now ready. Sweeten to taste and, if desired,
sprinkle the froth with a little cocoa powder.
Notes
• While making cappuccino, the flow of frothed milk or coffee can be
interrupted by pressing the ‘Cappuccino deliver’ touch key (12).
• If the milk in the container finishes while delivering frothed milk,
remove the container and add milk. Then re-attach it and press the
‘Cappuccino deliver’ touch key (12) to request cappuccino again.
• To ensure the complete cleanliness and hygiene of the milk frother,
always clean the circuits in the milk container lid after making
cappuccino. “PRESS CLEAN!” flashes on the display.
•Place a recipient under the milk spout.
•Press the CLEAN button on the lid (N3) and hold down for at
least 5 seconds to start the cleaning function. The appliance
displays the message “CLEANING” above a progressive bar. You
should not release the CLEAN button until the bar is complete
indicating that cleaning is concluded. When the CLEAN button
is released, the function stops. After cleaning, remove the milk
container and place in the refrigerator. The milk should not be left
out of the refrigerator for more than 15 minutes.
• To change the quantity of coffee or frothed milk the appliance
delivers automatically into the cup, proceed as described in the
section “Changing the quantity of coffee and milk for cappuccino”.
"Less dense" froth
NO froth
"Denser" froth
frothed milk
regulator
N3

Instruction manual CM465 / CM465SS / CM465GM20 Please keep this instruction manual for future reference
When the CLEAN button is released, the function stops. After cleaning, remove the milk
container and place in the refrigerator. The milk should not be left out of the refrigerator
for more than 15 minutes.
4. To change the quantity of coffee or frothed milk the appliance delivers automatically into
the cup, proceed as described in the section “Changing the quantity of coffee and milk for
cappuccino”.