Caple WD140BK User manual

Contact Caple on 0117 938 7420 or for spare parts www.caple.co.uk
Sense warming drawer
Instruction manual
WD140BK

Instruction manual WD140BK
Please keep this instruction manual for future reference
2
CONTENTS
Warnings 3
Proper Use Of The Appliance 4
Safety Instructions And Warnings 5
Disposal Of Packaging 7
Electrical Connection 8
Before The First Use 10
Appliance Controls 10
Operation 10
Temperature Selection 11
Load Capacity 12
Care And Cleaning 13
Troubleshooting 14
Installation 15
Techincal Data 18

Instruction manual WD140BK
Please keep this instruction manual for future reference
3
WARNINGS:
IMPORTANT INSTALLATION INFORMATION
-Please read this instruction manual carefully. This will
allow you to use your appliance in complete safety.
-Always keep the instruction manual handy.
-This appliance is exclusively for home use for heating
dishes.
-Caple shall not be held liable for damage to persons or
property due to incorrect installation, or incorrect use of
the appliance.
-Be sure to check the appliance once it has been
unpacked. If it has been damaged, do not use it and
contact your retailer straight away.

Instruction manual WD140BK
Please keep this instruction manual for future reference
4
PROPER USE OF THE APPLIANCE
-This appliance is compliant with current safety
regulations.
-Improper use may nonetheless cause damage to persons
and/or property.
-The inside of the appliance can reach a temperature of
up to 75˚C when the thermostat is set to the maximum
position. When taking out hot dishes, use appropriate
oven gloves as necessary.
-Remember that children have very delicate skin which is
more sensitive to heat.
-Therefore , do not allow children to play with the
appliance.
-If the on button is pressed , the drawer will start heating
and there is the danger of burns.
-This appliance is designed for domestic use only

Instruction manual WD140BK
Please keep this instruction manual for future reference
5
SAFETY INSTRUCTIONS AND WARNINGS
-This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
-Children should be supervised to ensure that they do not
play with the appliance.
-Do not use the appliance to keep warm , re-heat or cook
foods and beverages.
-Humidity from foods or beverages may cause problems
for the appliance.
-Do not lean or sit on the open drawer. The telescopic
carriage may be damaged.
-The maximum load of the drawer is 25 kg.
-Make sure that the appliance is firmly secured to the
cabinet.
-Do not keep plastic or flammable objects in the
appliance. When the appliance it turned on, these kinds
of objects may melt or catch fire.
-Do not use the appliance to heat the room.

Instruction manual WD140BK
Please keep this instruction manual for future reference
6
-Never use steam cleaners. They may cause short circuits
and damage the appliance.
-Never under any circumstances insert objects (e.g.
screwdrivers, pointed objects, paper, etc.) through the
slots in the protection grille of the heating element and
fan.
-If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified
person in order to avoid a hazard.

Instruction manual WD140BK
Please keep this instruction manual for future reference
7
DISPOSAL OF PACKAGING
The packaging materials protect the appliance during transport.
Recycling of the packaging makes it possible to save raw materials and reduce
waste volumes. If you dispose of the packaging yourself, ask local authorities for
the location of the nearest collection centre.
ENVIRONMENTAL PROTECTION
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your Local Authority or retailer for
recycling advice.
This appliance is marked according to the European directive 2002/96/EC on Waste
Electrical and Electronic Equipment (WEEE). By ensuring this product is disposed of
correctly, you will help prevent potential negative consequences for the environment
and human health, which could otherwise be caused by inappropriate waste
handling of this product. The symbol on the product indicates that this product may
not be treated as household waste. Instead it shall be handed over to the applicable
collection point for the recycling of electrical and electronic equipment. Disposal
must be carried out in accordance with local environmental regulations for waste
disposal.
For more detailed information about treatment, recovery and recycling of this
product, please contact your local council, your household waste disposal service or
the retailer where you purchased the product..

Instruction manual WD140BK
Please keep this instruction manual for future reference
8
ELECTRICAL CONNECTION
CONTACT A QUALIFIED ELECTRICIAN FOR THE ELECTRICAL CONNECTION OF
THIS PRODUCT
Before connecting the appliance to the electrical mains, ensure that the technical
data (voltage: V and frequency: Hz ) indicated on the rating plate concur with those
of the electrical mains.
This appliance has a 3amp fuse rating.
If in doubt, contact a qualified electrician.
If the plug is disconnected from the electrical power cord , a qualified electrician
will be required to insert and connect the appliance . Contact a qualified technician
who is knowledgeable of local standards and of any additional regulations issued by
the local electric company , and who ensures that work is carried out in compliance
with these standards.
IMPORTANT:
Check that the appliance is correctly connected to an approved earth wire to ensure
electrical safely. If necessary, have the system checked by a qualified electrician. If
the electrical outlet is no longer accessible after insertion, or if a fixed connection is
to be made, the installer must provide a separation device for each pole.
Valid separation devices include switches with a contact opening of at least 3mm.
Caple shall not be held liable for damage to individuals or property due to lack or
interruption of the earth wire.
ATTENTION: EARTH CONNECTION IS REQUIRED BY LAW.
If the appliance is connected to the mains with an extension cord. Make sure that
the extension cord and the connection are insulated against humidity.
Never open the covering of the appliance if you come into contact with wires
that carry voltage or if you modify the electrical and mechanical structure of the
appliance , it is possible that the appliance will malfunction during operation.

Instruction manual WD140BK
Please keep this instruction manual for future reference
9
If installation, maintenance and repair work is not carried out correctly, there may
be hazards for the user. Caple declines all liability for this type of personal injury
or property damage. During the warranty period , repairs may be carried out by
authorised service agents only. Otherwise, guarantee coverage will be void.
Installation, repair and cleaning work are to be carried out only with the machine
disconnected from the electrical mains. The appliance is disconnected from the
electrical mains in the following cases:
- The main switch of the electrical system is off.
- The safety switch is off.
- The appliance is unplugged.
USEFUL INFORMATION
The appliance is designed exclusively for the heating of dishes which are suited
for this purpose. The appliance is equipped with a hot air system. A fan creates
excellent distribution of warmth from the drawer heating element. Air circulation
heats the dishes evenly and quickly. A protection grille prevents contact with
the heating element and the fan. The base of the drawer is coverd with anti-slip
material to keep dishes from moving when it is opened or closed.

Instruction manual WD140BK
Please keep this instruction manual for future reference
10
BEFORE THE FIRST USE
- When using the appliance for the first time. Clean it as follows:
- Clean the surface with a soft cloth and then dry it.
- Pre-heat the empty drawer for at least two hours. Turn the temperature knob
to the maximum setting, in order to eliminate any residual grease, oil, or
manufacturing resins which may cause unpleasant odours during heating.
- Air out the room.
- Upon completion of this operation, the appliance is ready to be used for the
first time.
APPLIANCE CONTROLS
5
BEFORE THE FIRST USE
When using the appliance for the first time. Clean it as follows:
Clean the surface with a soft cloth and then dry it.
Pre-heat the empty drawer for at least two hours. Tum the temperature knob to the maximum
setting, in order to eliminate any residual grease, oil, or manufacturing resins which may cause
unpleasant odours during heating.
Air out the room.
Upon completion of this operation, the appliance is ready tobe used for the first time.
APPLIANCE CONTROLS
The control elements are the temperature knob and the luminous ON-OFF switch.
With the switch pressed (position 1) the drawer is on, whereas when the switch is released
(position 0) the drawer is off. These parts can be seen only when the drawer is open.
When the drawer is closed, a control light located on the front of the appliance lets you see
whether the drawer is on.
OPERAT ION
-Place the dishes in the drawer
-Select a temperature
- Turn on the appliance; the switch will light up
- Close the drwer gently
- Turn off the appliance before removing the heated dishes.
TEMPERATURE SELECTION
The temperature knob lets you select a temperature between approximately 30℃and 75℃.
Turn the temperature knob clockwise only, until it reaches it stop position (MAX).
Do not force it beyond the stop, otherwise thethermostat will be damaged.
The temperaturescale does not show absolute temperatures in ℃,but rather symbols that
represent the best temperature for respective groups of dishes, i.e cups - approx.40℃
The control elements are the temperature knob and the luminous ON-OFF switch.
With the switch pressed (position 1) the drawer is on, whereas when the switch
is released (position 0) the drawer is off. These parts can be seen only when the
drawer is open. When the drawer is closed, a control light located on the front of
the appliance lets you see whether the drawer is on.
OPERATION
- Place the dishes in the drawer
- Select a temperature
- Turn on the appliance; the switch will light up
- Close the drawer gently
- Turn off the appliance before removing the heated dishes.

Instruction manual WD140BK
Please keep this instruction manual for future reference
11
TEMPERATURE SELECTION
The temperature knob lets you select a temperature between approximately 30ºC
and 75ºC. Turn the temperature knob clockwise only, until it reaches it’s stop
position (MAX). Do not force it beyond this point, otherwise the thermostat will
be damaged.
The temperature scale does not show absolute temperatures in ºC,but rather
symbols that represent the best temperature for respective groups of dishes, i.e
cups - approx.40ºC.
For cups or glasses - approx 40ºC
When contained in glasses which are previously heated to this temperature, hot
beverages do not cool so rapidly and the container can nonetheless be touched
without any problem.
Plates/dishes - approx.60ºC
Foods placed in these dishes will stay warm longer. Depending on personal
sensitivity, the dishes can be touched without any danger. Use mitts or pot holders
if necessary.
MAX approx. 75ºC
For dishes.
The thermostat is set to the maximum temperature.
The containers can be touched with appropriate mitts or pot holders.
HEATING TIMES
The time required to heat dishes, glasses and so on depends on several factors:
- Material and thickness of the dishes
- Amount of load
- Arrangement of load
- Temperature setting
For this reason it is not possible to provide absolute information.
It is advisable to determine the best settings for your needs based on practical
experience.

Instruction manual WD140BK
Please keep this instruction manual for future reference
12
TROUBLESHOOTING
Repair of electrical appliances is to be carried only by qualified, authorised service
agents.
Improperly or incorrectly performed repairs may create further hazards for the safety
of the user.
Various factors affect heating time, for example:
Material and thickness of dishes, size of load, arrangement of load, temperature
setting. Optimal heating times for dishes are subjective. Therefore, it is advisable to
determine them on a trial and error basis according to your own preferences.
Troubles Solution
If the dishes are not warm
enough
the appliance is on
the right temperature has been set
the heat outlets have been covered by large plates or bowls
the dishes have been heated for a sufficient period of time.
If the dishes do not get
warm
there is fan noise: the fan is working, but the heating element
might be defective
if the fan is not working, it may be defective
the main switch of the electrical system is off.
the electrical power cord is unplugged or damaged
If the dishes overheat: the temperature setting device may be defective
The on/off switch does not
light up when th appliance is
switched on:
the control light of the switch is dfective
If the problem still persists, please contact Caple service for assistance:
T - 0117 938 7420
E - [email protected]

Instruction manual WD140BK
Please keep this instruction manual for future reference
13
INSTALLATION
Safety instructions for installation
Before connecting the appliance to the electrical mains, compare the connection
data (voltage and fraquency) indicated on the rating plate with the data of the
electrical mains.
The data must match, otherwise the appliance may be damaged.
If in doubt, contact a qualified technician.
Make sure that the electrical outlet is easily accessible even after the appliance has
been inserted. The warming drawer can only be inserted with other appliances with
a maximum weight of 40 kg that are provided with adequate cooling ventilation.
For installation with combination appliances, follow the instruction and building in
dimensions shown in the ‘Installation dimensions’ section.
Insertion and installation of this appliance may be performed by qualified personnel
who ensure safe operating conditions.
Insertion space measurements
The dimensions of the housing are obtained from the size of the warmer drawer
plus measurements of the appliance combined with it.

Instruction manual WD140BK
Please keep this instruction manual for future reference
14
LOAD CAPACITY
Load capacity depends on the size of the dishes.
The following examples are approximate.
Also remember that drawer can sustain a maximum weight of 25kg.
This warming drawer is designed to hold 6 place settings.
Note: These examples are a guide only. The actual quantities may differ.
Or a choice of :
16 plates ø26cm
24 soup dishes ø22cm
30 soup bowl ø10cm
10 plates ø28cm
10 pizza plates ø36cm
60 espresso cups
30 cappuccino cups
30 glasses

Instruction manual WD140BK
Please keep this instruction manual for future reference
15
CARE AND CLEANING
Cleaning operations are to be undertaken only when the machine is disconnected
from the electrical mains. The appliance is disconnected from the electrical mains in
the following cases:
- The main switch of the electrical system is off.
- The safety switch is off.
- The appliance is unplugged.
When unplugging the appliance, do not pull on the cord. Take hold of the plug and
remove.
Clean all surfaces with a soft sponge, a bit of detergent and lukewarm water. Then
dry all surfaces with a soft cloth.
IMPORTANT:
The area of the grille for the protection of internal components and the area of the
switch and thermostat must not be cleaned with water.
Any penetration of liquids or other substances into electrically live parts may cause
failures or short circuits, creating hazards for the user.
The front of the appliance can easily scratch if mistreated.
The glass surface should be cleaned with a special non-abrasive product.
Do not use:
Detergents that contain soda, acids or chloride, abrasive detergents (powder or
cream) abrasive sponges (e.g.steel wool pads) or sponges that contain residual
abrasive detergent.
Anti-slip bottom
The anti-slip bottom of the drawer can be cleaned for thorough cleaning of the
drawer. The bottom can be hand-washed with warm water and a gentle detergent.
Dry thoroughly afterwards.
Put the anti-slip bottom back in the drawer only when it is completely dry.

Instruction manual WD140BK
Please keep this instruction manual for future reference
16
INSTALLATION DIMENSIONS
*Please note the 45cm oven dimensions may vary from the above depending on
which model is used
Dimensions
594mm
560mm
548mm
129.6mm
143.8mm
595mm
560mm
401mm 546.7mm
511.3mm
455mm
438mm
546mm
595mm
7
.
5mm
1.4mm
116mm

Instruction manual WD140BK
Please keep this instruction manual for future reference
17
TECHINCAL DATA
Total power:
380-460W
Connection and protection:
AC 220-240V/50 Hz

Instruction manual WD140BK
Please keep this instruction manual for future reference
18

Instruction manual WD140BK
Please keep this instruction manual for future reference
19

Instruction manual WD140BK
Please keep this instruction manual for future reference
20
Caple Service
Fourth Way
Avonmouth
Bristol
BS11 8DW
t: 0117 938 7420
e: [email protected]
www.caple.co.uk