CARDIOSPORT ZA5D User manual

Model No.: ZA5D
Brand Name: CARDIOSPORT
Product Name: Solo Speed/Cadence
Sensor
User's manual

z
SOLO
SPEED & CADENCE SENSOR
INSTRUCTIONS
Installing your Speed Sensor
Please remove the battery isolator before
installing the speed sensor on your bike by
opening the battery door and peeling off the
sticker on the battery
Cardiosport Top Tip: To make installing the
speed or cadence sensor easier, secure your bike
on a stand or upside down for better access to the
wheel hub.
1. Push the speed sensor pod <A> into the
accompanying pod mount <B>. Use the
arrows on the bottom of the sensor pod to
align with the mount and secure a tight fit.
2. Place the mount <B> with speed sensor pod
<A> on top of the rubber base <C>
3. Fit the elastic band <D> in the vertical hook
on the pod mount <B> and place the speed
sensor onto the wheel hub and pull the elastic
band around the wheel hub and attach into
the opposite vertical hook.
4. Ensure that the speed sensor is fitted securely
and push the sensor to the centre of the
wheel hub.
Note: The Blue LEDs will flash when the sensor
is awake and in advertising mode.
Installing your Cadence Sensor
Pease remove the battery isolator before
installing the cadence sensor on your bike
1. Push the speed sensor pod <A> into the
accompanying pod mount <B>. Use the arrows
on the bottom of the sensor pod to align with the
mount and secure a tight fit.
2. Select the elastic loop <D> length that best fits
your crank arm. Then place the sensor pod <A>
inside the mount <B> on top of the rubber base
<C>.
3. On the non-drive/outside left crank arm, place the
cadence sensor in the centre of the inside of the
crank arm.
4. Attach the elastic loop <D> to the vertical hook
on the pod mount and pull the loop around the
crank arm and attach into the opposite vertical
hook.
5. Rotate the crank arm a number of times to check
for clearance between the bike frame and the
sensor is securely mounted.
For crank arms with a deep recess that cannot
support the cadence sensor. Use the cadence sensor
pod <A> without the pod mount <B> and securely
attach to the outside left crank arm using strong 3M
doubled sided sticky tape. 
Pairing the Speed and Cadence
Sensors with your device
Pairing is the process of connecting the sensors to
either a Bluetooth or ANT+ device. Please check your
device uses either Bluetooth Low Energy or ANT+
wireless technology to be compatible with the sensors.
Please note: The pairing procedure can differ between
each compatible Bluetooth or ANT+ device, we
recommend referring to your user manual for your
device(s).
Bluetooth pairing
1. Move the Bluetooth compatible device within 3m
of the speed and cadence sensors
2. Activate Bluetooth on your device
3. Follow the pairing instructions for Bluetooth
compatible accessories on your device
4. Blue LED lights will flash on the speed and
cadence sensors to indicate that they are awake
are ready to pair. If the sensors do not appear
straight away, try shaking them to wake them up
or select refresh or search again on your
Bluetooth device.
5. Once the sensors have been paired, some
devices may ask you to save the sensors so that
it will automatically recognize them each time they
are active and there is no need to repair them.
ANT+ pairing
1. Move the ANT+ compatible device within 2m of
the sensors
2. Follow the pairing instructions for your ANT+
device for speed and cadence sensors
3. Once the sensors have been paired, your ANT+
compatible device will automatically recognize the
sensors each time they are active and there is no
need to repair them
4. Blue LED lights will flash on the speed and
cadence sensors to indicate that they are awake
and ready to pair. If the sensors do not appear
straight away, try shaking them to wake them up
or select refresh or search again on your ANT+
device.
WARNING

Do not use a sharp object to remove the battery
 Please keep batteries out of reach of children
 Do no put batteries in your mouth. If swallowed
contact your physician or local poison control
centre immediately.
 Replaceable coin cell batteries may contain
perchlorate material and special handling may
apply. See
www.dtsc.ca.gov/hazardouswaste/perchlorate
Contact your local waste disposal department
for recycling coin cell batteries.
CAUTION
Battery Replacement Guide
1. Find the battery door located on the underside
of the sensor pod <A>.
2. Rotate the battery door cover counter-
clockwise until the door lifts up and is loose
enough to remove.
3. Remove the cover and carefully pull the
battery out.
Cardiosport Top Tip: Batteries can be removed
using a magnet or piece of sticky tape.
4. Wait for around 20-30 seconds
5. Insert a new battery into the battery slot with
the flat side of the battery facing down.
6. Once the new battery is in place, reattach the
battery door by placing the door over the
markers and rotate clockwise until the battery
door fits flush with the sensor pod under-side.
The LED lights will flash Blue when the new
battery is installed and the sensor becomes awake
again.
A
B
C



SOLO
SPEED & CADENCE SENSOR
INSTRUCTIONS
PLEASE REMOVE
BATTERY ISOLATOR
BEFORE USE
Limited Warranty
The Cardiosport Speed and Cadence
sensors are covered by the standard
Cardiosport limited warranty. For more
details please visit:
www.cardiosport/cardiosportwarranty.com
SOLO Speed and Cadence Sensor
Specifications
Operating range 2-60 MPH 18-220
RPM
Battery type User replaceable
CR2032 3 volts
Battery life Approximately 12
months at (1 hour
everyday use)
Radio frequency
protocol
Bluetooth Low
Energy 2.4GHz and
ANT+ Wireless
communications
protocol
Water rating IPX7 Water
Resistant
Operating
temperature
range
From 0 ˚C to 60 ˚C
Weight 8 grams (each)
Size 28mm Diameter
Maximum output
power
BLE: 0.89 dBm
ANT+: 0.12 dBm
Peak active
current
Typical 12mA
Stand-by-current Less than 1.5uA
LED output
current
Typical 2mA
Important Product Information
Certification Sheet
Contact:
Healthcare Technology Ltd
Dragoon House
Hussar Court
Waterlooville
Hampshire
PO7 7SF
United Kingdom
Caution:
The manufacture is not responsible for any radio or
TV interference caused by any unauthorized
modifications made to this product. Such
modifications could void the users authority to use
the product.
CE Statement:
Hereby, [Zentan Technology Co., Ltd.] declares that
the radio equipment type [Solo Speed/Cadence
Sensor Model no.: ZA5D] is in compliance with
Directive 2014/53/EU. Regulatory authorities in the
EU may obtain compliance information by writing to
us at:
Healthcare Technology Ltd
Dragoon House
Hussar Court
Waterlooville
Hampshire
PO7 7SF
United Kingdom
California Proposition 65:
The enclosed product (hardware) and its packaging
contain chemicals the state of California has found to
cause cancer, birth defects or reproductive harm.
FCC Rules Part 15:
The enclosed product (hardware) device complies
with part 15 of the FCC Rules. Operation is subject to
following two conditions: (1) this device may not
cause harmful interference and (2) it must accept any
interference received, including interference that may
cause undesired operation.
This Important Product Information
Guide contains safety and handling,
regulatory and warranty information.
Battery Safety: Most Cardiosport products contain
coin cell batteries. Keep batteries away from
Children. Never put batteries in mouth. Swallowing
can lead to chemical burns, perforation of the soft
tissue, and death. Severe burns can occur within 2
hours of ingestion.
Only replace batteries with correct replacement
batteries. Using other batteries poses a risk for fire
and explosion. Do no use sharp tools to remove
user-replaceable cell. Do not remove or attempt to
remove non-user replaceable batteries.
If you use this product with navigation software,
always be aware of your surroundings. This product
contains no user serviceable parts and repairs, any
modifications should only be made by a Cardiosport
technician. Any unauthorized modifications or
repairs will void your warranty. Do not leave product
exposed to excessive heat or cold.
FCC Compliance Statement:
This equipment has been tested and found to
comply with limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in residential
installations. This equipment generates, uses, and
can radiate radio frequency energy, and if not
installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does cause
interference to radio or television equipment
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try
correct the interference by one or more of the
following measures. Reorient or relocate the
receiving antenna Increase the separation between
the equipment and receiver Connect the equipment
into an outlet on a circuit different from that to which
the receiver is connected.
Compatible apps
Strava Zwift Endomondo Wahoo
Fitness
Map My Ride with Cyclemeter Map My
Ride GPS Fitness
INSIDE THE BOX
A B
C D

Zentan Technology Co., Ltd.
NO.92, Hsing-Sheng Road, Chia-Li District, Tainan City,
72254 Taiwan RF_067, Issue 01
EU Declaration of Conformity (DoC)
Hereby we,
Name of manufacturer: Zentan Technology Co., Ltd.
Address: NO.92, Hsing-Sheng Road, Chia-Li District,
Zip code & City: Tainan City, 72254
Country: Taiwan
Telephone number: 886-6-7232226
declare that this DoC is issued under our sole responsibility and that this product:
Product description: Solo Speed/Cadence Sensor
Type designation(s): ZA5D
Trademark: CARDIOSPORT
Batch / Serial number: 1729s
Object of the declaration (further identification of the radio equipment allowing traceability; it may include a color
image for the identification of the radio equipment):
Brand name: CARDIOSPORT Model no.:ZA5D(Cadence Sensor)
Brand name: CARDIOSPORT Model no.: ZA5D(Solo Speed)
is in conformity with the relevant Union harmonization legislation:
Radio Equipment directive: 2014 / 53 / EU
and other Union harmonization legislation where applicable:
Waste Electrical and Electronic Equipment (WEEE): EU DIRECTIVE
2012/19/EC
with reference to the following standards applied:

Zentan Technology Co., Ltd.
NO.92, Hsing-Sheng Road, Chia-Li District, Tainan City,
72254 Taiwan RF_067, Issue 01
EMC: Draft EN 301 489-1 V2.2.0 (2017-03)
EMC: Draft EN 301 489-17 V3.2.0 (2017-03)
Radio Spectrum: EN 300 328 V2.1.1 (2016-11)
Safety: EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013
Health: EN 62479 (2010)
The Notified Body Telefication B.V., with Notified Body number 0560 performed: [Module B]
Where applicable:
The issued the EU-type examination certificate: [note certificate number]
Description of accessories and components, including software, which allow the radio equipment to operate as
intended and covered by the DoC:
.…………………………………………………………………………………………………………
Signed for and on behalf of:
July 14, 2017 Hunter Hsieh / R&D Manager
Place and date of issue Name, Function, signature