CareCo MALMO DL06278 User manual

Thank you for deciding to purchase the Malmo Trolley
from CareCo.
The Trolley is manufactured from the nest materials
and components available. When used correctly it is
designed to give many years of reliable trouble-free
service.
CareCo (UK) Limited, 1 Turing Court, Great Notley, Braintree, CM77 7AT | 0333 015 5000
PRODUCT CODE DL06278
Before Use
Carefully remove all packaging. Avoid using
any knives or other sharp instruments as this
may damage the surface of the item.
Check the product for any visible damage If
you see any damage or suspect a fault, do not
use your product, but contact your supplier for
support.
Height Adjustment
• Your trolley can be adjusted in height if
required.
• To adjust the height remove the lower ‘E’
clips from the extension legs and pull each
leg to the desired height. (See g. 1.)
• Ensure that all four extension legs are
evenly adjusted.
• Re-insert all ‘E’ clips facing the line of travel
also ensuring that the ‘E’ clips have passed
through the product frame and extension
leg and are secure. (See g 2.)
• Never adjust the legs unevenly; this is
dangerous and can seriously compromise
the safety of the user.
IMPORTANT! This equipment must
be installed by a competent person.
MAXIMUM WEIGHT ON TRAY: 15KG
Do not exceed the weight limit
stated - doing so could put the
user at risk.
15
DL06107 - Home Help Trolley
Thank you for deciding to purchase the Home Help Trolley from CareCo.
The Trolley is manufactured from the nest materials and components available. When used
correctly it is designed to give many years of reliable trouble-free service.
Carefully remove all packaging. Avoid using any knives or other sharp instruments as this may
damage the surface of the item.
Check the product for any visible damage If you see any damage or suspect a fault, do not use your
product, but contact your supplier for support.
Your trolley can be adjusted in
height if required.
Check that the trolley is sitting evenly on the oor and there is no excessive rocking or the trolley is
tilting to one side. If this is the case, please do not use the trolley, but repeat the above steps to correct
the problem or contact your supplier for service support.
• To adjust the height remove the
lower ‘E’ clips from the extension
legs and pull each leg to the
desired height. (See g. 1.)
• Ensure that all four extension legs
are evenly adjusted.
• Re-insert all ‘E’ clips facing the
line of travel also ensuring that the
‘E’ clips have passed through the
product frame and extension leg
and are secure. (See g 2.)
• Never adjust the legs unevenly;
this is dangerous and can seriously
compromise the safety of the user.
IMPORTANT!
BEFORE USE
HEIGHT ADJUSTMENT
N.B. This equipment must be installed by a competent person.
Do not exceed the weight limit stated - doing so could put the user at risk.
Maximum Weight on Tray: 15kg
E-Clip
Fig.2
Fig.1
Product Frame
Product Frame
E-Clip passed
through
punched holes
in product
frame and
extension leg
Extension Leg
Extension Leg
Punched Holes
Check that the trolley is sitting evenly on the oor and there is no excessive rocking or the trolley
is tilting to one side. If this is the case, please do not use the trolley, but repeat the above steps
to correct the problem or contact your supplier for service support.

CareCo (UK) Limited, 1 Turing Court, Great Notley, Braintree, CM77 7AT | 0333 015 5000
PRODUCT CODE
DL06278
Cleaning
The polypropylene clip on trays can be removed for cleaning. To remove, place your
nger and thumb on the underside of the U clip over inverted U section, push upwards
and remove.
The tray can be cleaned with either a mild detergent or disinfectant, or alternatively
pressure washed or autoclaved at a temperature of up to 100°C.
Cleaning the castors and wheels
The polypropylene castors or steel bodied castors can be removed from the frame by
removing the ‘E’ clip retaining the extension leg. Once done, wash the castor in a bucket of
mild detergent or disinfectant.
However ensure that you thoroughly dry the castor and extension leg prior to reassembly
and nish by applying a water-dispersing agent such as WD40 over the castor wheel and
body prior to reassembly. Following cleaning, please repeat all steps detailed in section 2,
adjustment of leg with castor attached.
Cleaning the castors and wheels
Please make a safety check of the product at regular intervals or if you have any concerns.
Important Information
The information given in this instruction booklet must not be taken as forming part of or
establishing any contractual or other commitment by CareCo UK Ltd or its agents or its
subsidiaries and no warranty or representation concerning the information is given.
Please exercise common sense and do not take any unnecessary risks when using this
product;as the user you must accept liability for safety when using the product. Please
do not hesitate to contact the person who issued this product to you or the manufacturer
if you have any queries concerning the assembly/use of your product.