Carisma CTX-8000 User manual

Manufactured by : MUN AH PLASTIC ELECTRONIC TOYS CO., LTD.
MAN-G00546
Visit Us on www.carisma.com.hk
Printed in China
© 2015 Carisma. All Rights Reserved. Product specifications are subject to change.
Some models shown are prototypes which may vary slightly from what is inside.
ABOUT THE RADIO SYSTEM
CTX-8000
ST. Trim Dial
TH. Trim Dial
* In general, user will experience under steer when making a wide turn at high speed
or over steer when making sharp turn at high speed (easy to spin out). User should
practice the Throttle and steering approach for dierent cornering at dierent speed
or road surface.
Battery Installation
The following is an overview of the various functions and adjustments found on CTX-8000 radio system for Carisma models. It is important to read and
understand about all of these functions and adjustments before driving.
Carisma CTX-8000 2.4GHz FHSS Technology System
Functions
TRANSMITTER CTX-8000
Steering Wheel : Control direction (Left/Right) of the RC model.
Throttle Trigger : Control speed and direction (Forward/Brake/Backward)of the
driving model.
ON / OFF Switch : Power ON / OFF the transmitter.
FTN Key : Top Green LED light indicates synchronization status and/or adequate
battery power supply.
Power Indicator : Green LED light indicates Power “ON”. Red LED indicates battery low.
ATV : Adjust the same maximum steering angle on both sides when model turns
Left / Right.
ST. Trim Dial : Adjust the neutral position of steering servo when model wheels
are straight ahead.
TH. Trim Dial : Make sure the model stays still when releasing the Throttle Trigger.
Steering Reverse : Reverse the response direction when operating Steering Wheel.
Throttle Reverse : Reverse the response direction when operating Throttle Trigger.
1. Supplied with 4 x 1.5V AA Batteries,
CTX-8000 can be operated a few hours.
Installation: Remove the battery
compartment cover as shown below.
2.Install the batteries observing
the polarity marked on battery
compartment.
3.Then reinstall the battery
compartment cover as the
Picture shown below.
Warning :
Never disassemble batteries or put the batteries
in fire, chemical agents, otherwise they may cause
personal injuries or property damages.
Battery Disposal :
Observe corresponding regulations about wasted
battery treatment regulations.
1. After running out of power, dispose of wasted
batteries in designated areas far away from
water supply, household areas and planted areas.
2. Submit the wasted batteries to specific recycling
stations.
Battery LED Indicator
The Green LED indicator located on the front left side of the transmitter indicates
the power supply of batteries. The green LED will go solid on indicating that
the batteries have sucient power. When batteries voltage drops below 4
volts, LED will turn to Flashing RED, indicating the batteries power is low and
should be replaced.
Pre-Run Check
Steering
Wheel
Throttle Trigger
Power
Indicator
Steering
Reverse
Throttle
Reverse
ATV
FTN Key
ON/OFF
Switch
* Always turn on the transmitter first by sliding
the switch on the left side from bottom to top.
The small red and green lights above the
switch should both light up. If not, you need
to check for low or incorrectly installed
batteries.
Reversing
Reversing is used to change the response direction of steering wheel and throttle
trigger. CTX-8000 Transmitter features 2 reversing functions: Steering Reverse
and Throttle Reverse.
Steering Reverse: Reverse the response direction when operating steering wheel.
Turning left steering wheel, the model turns right while turning right the model
turns left.
Throttle Reverse: Reverse the response direction when operating throttle trigger.
Pushing forward throttle trigger the model moves backward while pulling back,
the model moves forward. If necessary you can just use a small screwdriver to
adjust the or responding switches.
ATV enables to adjust the same maximum steering angle of servo on both sides
(Left and Right) when model makes steering. The ATV aects the sensitivity
of servo. Reducing dual rate value can lower the sensitivity of servo and reduce
the same maximum steering angle on both sides. Remember to adjust the ATV
within the adjustment range.
ATV
1. Steering : Adjust the steering trim to keep
the front wheels in straight line when steering
wheel remains in NEUTRAL position.
2. Throttle : Adjust the throttle trim to ensure
the rear wheels stop rotating when throttle
trigger remains in NEUTRAL position.
Solid GREEN :
Sucient Power supply
Flashing RED :
Time to replace batteries
INSTRUCTION MANUALINSTRUCTION MANUAL
GREEN
TROUBLE SHOOTING GUIDE
Short running times / Running slow
• ST. Trim Dial tuning not good
When the Throttle Trigger on Stop
position, Model Car is running
• Tune the ST. Trim Dial
• ST. Trim Dial not no center • Tune the ST. Trim Dial
Model car out of control
Remote control distance too close
Steering Not working properly
• Throttle Reverse not set good
L/R Steering phase inversion
Forward/Backward Throttle
phase inversion
• Check and push the Throttle Reverse SW
• Steering Reverse not set good • Check and push the Steering Reverse SW
• ESC mode "Forward Only with Brake" is
selected BLUE LED Flashing at STOP position.
3 wire servo No Function • 5 wire servo is connected • Power OFF the unit. Disconnect 5 wire
servo ans power on the unit
ESC NO Function
ESC NO Reverse Function
• Select ESC mode "Forward / Reverse with Smart
Brake "according to Page X" ESC Program Setup
Flow Chart
Problem Possible Cause Solution
• The Battery charge up not full
• The Battery power will ues up
• Wheel Nut too squeeze
• Drive system not soomth
• Recharge the battery full
• Recharge the battery full
• Loosen the Wheel Nut
• Full check the Drive system parts
Running not straight
• Replace the new AA size alkaline battery
• Replace the new Receiver
• Replace the other place
• Transmitter Battery not power
• Receiver antenna breakdown
• Influenced by the environment
• Transmitter Battery low
• Model car battery power will ues up
• Transmitter antenna breakdown
• Check and Replace the new AA size alkaline battery
• Check and Recharge the battery full
• Check or Work on the repairs
• Servo Gear breakdown
• Servo Saver breakdown
• Recharge the new Servo
• Recharge the new Servo Saver
• Overheat Proection: RED and BLUE LED
alternative flashing quickly
• Motor Stalled Protection: RED LED flashes quickly
3 times, Turn OFF for a while and Repeat again.
• Over Voltage Protection (Battery over 13V):
RED LED SOLID ON and BLUE LED Flashing
ONCE per second.
• Under Voltage Protection (Battery under
10.2V for 3S LIPO / 6.8V for 2S LIPO / 48V for NiHM):
BLUE LED SOLID ON and RED LED Flashing ONCE
per second.
• WAIT until the Unit cool down completely
• WAIT until the Unit cool down completely
• Replace battery pack
• Replace battery pack
Receiver No Function • Signal Loss
• Green Led Flashing Twice Continuously
• Check Transmitter Power on or NOT,
• or Check Binding is OK or NOT
ATV
Reversing
SAFETY PRECAUTIONS
FOR TRANSMITTER
Damages or
Leaking.
Do not use any
damaged
batteries.
x4
This product must never be thrown away with other waste. Thus the users are liable for
disposing the wasted model by submitting them to designated collection stations specific
for recycling electronic and electric items. Disposing of the wasted model in this way is
helpful to conserve natural resources and enable to keep human health and protect the
environment. For more information about wasted model disposal and recycling, please
contact your local city oce, your disposal service or where you purchased the product.
Instructions for Disposal of WEEE by Users in the European Union
Heavy Duty
1.5V “AA” Size Batteries
(INCLUDED)
ATTENTION
Car Battery
(NOT INCLUDED)
Safety Precautions Introduction
THIS MODEL IS ONLY SUITABLE FOR PEOPLE 14 YEARS OLD AND UP.
THIS RADIO CONTROL MODEL IS NOT A TOY.
Beginner should seek advice from experienced person in order to assemble the model
or parts correctly and to make best performance.
* Assemble this model or parts only in place out of children’s reach, and take safe
precautions before operating this model. User is fully responsible for the model
assembly and safe operations.
This is a sophisticated hobby product and not a toy. It must be operated with
caution and common sense. User also requires some basic mechanical abilities.
Fail to operate this product in a safe and responsible manner could result in injury
or do damage to the product or other properties. This product is not intended for
use by children without direct adult supervision. The product manual contains
instructions for safe operation and maintenance. It is essential to read and follow
all the instructions and warnings in the manual prior to assembly, setup or use, in
order to operate correctly and avoid damage or injury.
UK
FI
CZ
AT
NL FR
DE
EE
SK
IT LU
DK
LV
HUES
MT
BG
LT
RO PT
CY
SE
PL SI IEGR
The associated regulatory agencies of the following countries recognize the
noted certifications for this product as authorized for sale and use.
CE Compliance Information For The European Union
Declaration of Conformity
Products: Carisma CTX-8000 2.4GHz Transmitter, MRS-540BL Receiver
Equipment Class: 2
The objects of declaration described above are in conformity with the
requirements of the specifications listed below.
Statement - This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2)this device must accept any interference received, including interference
that may cause undesired operation.
FCC ID YDTCTX-8000
RF Exposure Warning:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
And should be operated with minimum distance of 20 cm between the
antenna & your body.
Item Name : Carisma CTX-8000 2.4GHz Transmitter and MRS-540BL Receiver
EN 301 489-1 V1.9.2
EN 301 489-17 V2.2.1
ETSI EN 300 328 V1.8.1
Safety, Precautions, and Warnings
As the user of this product, you are solely responsible for operating it in a manner that
does not endanger yourself and others or result in damage to the product or the property
of others.
This model is controlled by a radio signal that is subject to interference from many sources
outside your control. This interference can cause momentary loss of control so it is
necessary to always keep a safe distance in all directions around your model, as this will
help to avoid collisions or injury.
• Always operate your model in an open area away from cars, traffic, or people.
• Avoid operating your model on the street where injury or damage can occur.
• Never operate the model out into the street or populated areas for any reason.
• Never operate your model with low transmitter batteries.
• Carefully follow the directions and warnings for this product and any optional support
equipments (chargers, rechargeable battery packs, etc.) that you use.
• Keep all chemicals, small parts and anything electrical out of the reach of children.
• Moisture causes damage to electronics. Avoid water exposure to all equipments not
specifically designed and protected for this purpose.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Directive 1999/5/EC (R&TTE)
Article 3.1a Health
Article 3.1b EMC
Article 3.2 Radio Spectrum

ENTER SETUP MODE
SETUP FLOW CHART
Pull the Throttle Trigger to Max. Forward
position to toggle Battery type
Display CURRENT Battery type instantly
RED LED ON = LiPO Battery
BLUE LED ON = NiHM Battery
RECEIVER UNIT (MRS-540BL) FUNCTIONS
15
1
2
4
Power ON the Transmitter
BLUE LED ON
(Indicate “Select Battery Type”)
HOLD the Throttle Trigger to
Max. Forward Position
Power ON Receiver Unit(MRS-540BL)
3
HOLD the Throttle Trigger until
RED & BLUE LED Alternatively
Flashing with a “BEEP” sound
Release Throttle Trigger
BATTERY TYPE SELECTION MODE
RED LED ON
(Indicate “Calibration Mode”)
CALIBRATION MODECALIBRATION MODE
RED and BLUE LED ON
(Indicate “Select ESC Mode”)
ESC SPORT / RACING MODEESC SPORT / RACING MODE
2
Pull the Throttle Trigger to Max.
Forward position and then release
After
4 Second
After
4 Second
Neutral
Position
Flashes
3 times with
3 “BEEP”
Sound
Power OFF the Receiver Unit to Escape
from Setup mode.
4
Pull the Throttle Trigger to Max. Forward position.
RED LED OFF and BLUE LED Flashes
Then BLUE LED OFF and RED LED FLASHES Pull the Throttle Trigger to
Max. Forward position. RED LED SOLID ON with a “BEEP” sound and BLUE
LED FLASHES Max Forward has been set.
Push the Throttle Trigger to Max. Reverse position.
RED and BLUE LED SOLID ON with a “BEEP” sound.
Max. Reverse has been set.
Release Throttle Trigger to Neutral position
BLUE LED SOLID ON with a “BEEP” Sound, then
Throttle Neutral Position has been set.
Release Throttle Trigger to Neutral position
RED and BLUE LED FLASHES 3 times with 3 “BEEP” sound.
Calibration has been completed.
Pull the Throttle Trigger to Max. Forward position to toggle ESC mode. When
ESC mode is selected, RELEASE Throttle Trigger.
After 4 second, RED and BLUE LED FLASHES 3 times with
3 “Beep” sound. ESC mode setup has been completed.
Power OFF the Receiver Unit to
Escape from Setup mode.
Power OFF the Receiver Unit to Escape
from Setup mode.
6
Display CURRENT ESC Mode instantly
Sport Mode : BLUE LED ON =
Forward/Reverse with Smart Brake
Racing Mode : BLUE LED FLASHES =
Forward Only with Brake
APPROX 2 sec.
APPROX 2 sec.
APPROX
2 sec.
1. When Battery type has been Selected, RELEASE the Throttle Trigger to
Neutral position.
2. After 4 second, selection made with RED and BLUE LED Flashes 3 times
with 3 “BEEP“ sound, Battery Select has been completed.
2
3
“BEEP”
5 4
31
6
12
5 4
3
Pull Neutral
Position Pull
“BEEP”
FlashesFlashes
Push
Neutral
Position
Flashes
3 times with
3 “BEEP”
Sound
FlashesFlashes
24
13
Sport ModeSport Mode
Pull and
Release Racing Mode
Racing Mode Neutral
Position
Flashes
3 times with
3 “BEEP”
Sound
After
4 Second
After
4 Second
If fail to Bind, suggest to repeat from begin to try again
“BEEP”
“BEEP”

M40P0305-03
M40P0306-03
M40P0602-02
R14P1111
MASM053A
MASM1724A
MASM1724A
R14P1111
SSW-G00267
M40P0208
SSW-G00140
SSW-G00158
MASM2309A
SSW-G00235
Receiver Unit
MRS-540BL
MASM038A
MASM2277A
MOT-G00120
MASM011A
MASM038A
M40P0701
MASM035A
MASM667A
MASM212A
MASM1185A
M40P0905-01
M40P1003
MASM2217A
M40P0307-03
SSW-G00376
MASM2218A
MASM2219A
M40P0704-01
M40P0503
M40P0602-02
M40P0308-03
M40P0902
LIPO00020
M40P0806
MASM2504A
SSW-G00190
M40P0101-01
MASM2508A
Rear Oil Shock
SSW-G00129
SSW-G00129
M40P1203
MASM034A
M40P0405-02
Rear Turnbuckle
MASM1011A
RBT-G00025
SSW-G00281
MASM017A
SSW-G00209
M40P0401-02
Front Turnbuckle
Steering Turnbuckle
M40P0403-01
SSW-G00652
M40P0803
Servo
BODYMOUNTP0103
SSW-G00272
SSW-G00019
BODYMOUNTP0104
Front Oil Shock
SSW-G00717
BODYMOUNTP0106
MASM2493A
MASM012A
MASM033A
MASM2216A
M10P0901
M40P0501
MASM1168A
SSW-G00156
MASM019A
EVA-G00195
Servo Turnbuckle
MASM2495A
M40P0601-02
M40P1601-01 SSW-G00019
BODYMOUNTP0105
M40P0802-01
M40P0801-01
SSW-G00196
MASM1068A
M40P0203-02
M40P0804
MASM1011A
EVA-G00121
M40P0703
MASM034A
MASM668A
MASM013A
MASM034A
MASM2492A
MASM2497A
SSW-G00129
MASM015A
SSW-G00201
SSW-G00129
M40P1201
SSW-G00233
SSW-G00192
SSW-G00192
SSW-G00190
MASM033A
M40P0902
MASM2218A
MASM2219A
MASM2219A
MASM2219A
SSW-G00106
MASM2217A
MASM035A
MASM035A
MASM038A
MASM2277A
MASM2276A
SSW-G00188
SSW-G00192
SSW-G00192
SSW-G00192
SSW-G00192
MASM013A
SSW-G00196
MASM012A
DCL-G00233
MASM013A
SSW-G00272
SSW-G00188
MASM668A
MASM013A
SSW-G00652
SSW-G00188
SSW-G00188
SSW-G00207
SSW-G00188
SSW-G00188
SSW-G00207
M40P1003
MASM2504A
MASM2504A
SSW-G00188
SSW-G00209
SSW-G00188
SSW-G00281
SSW-G00207
SSW-G00188
MASM2278A
MASM667A
M40P0705
MASM035A
SSW-G00106
MASM2219A
MASM2218A
MASM2219A
MASM2216A
SSW-G00156
SSW-G00156
MASM033A
MASM2493A
MASM2495A
MASM015A
SSW-G00129
SSW-G00201
EVA-G00121
RBT-G00025
M40P0601-02
SSW-G00188
SSW-G00192
MASM013A
SSW-G00192
M40P1601-01
MASM013A
SSW-G00192
SSW-G00192
SSW-G00235
SSW-G00192
SSW-G00192
SSW-G00235
SSW-G00193
SSW-G00193
SSW-G00235
SSW-G00156
SSW-G00201
M10P0901
M40P0505
MASM2504A
M40P0805
MASM013A
SSW-G00207
SSW-G00207
MASM053A
MASM1724A
R14P1111 MASM053A
MASM1168A
MASM053A
SSW-G00193
MASM212A
SSW-G00267
SSW-G00193
MASM1185A
M40P0703
MASM017A
MASM034A
MASM013A
MASM2492A
SSW-G00233
SSW-G00201
MASM019A
MASM2218A
MASM212A
MASM2450A
MASM2504A
MASM053A
MASM033A
MASM013A
MASM2503A
SPC-G00012
MASM2519A
SPC-G00011
MASM889A
MASM2520A
MASM2161A
MASM1011A
MASM2521A
MASM214A
MASM214A
M40P1101DTMSV
M401101BMWDTMGM
M40P11F-AUDISV
BENZ AMG C-COUPE DTM
AUDI RS5 DTM
BMW M4 DTM
DTMP0209
BMWDTMP0112
AUDIP0124
PART NO.
M40P1101DTMSV
M401101BMWDTMGM
M40P11F-AUDISV
EVA-G00195
EVA-G00200
EVA-G00201
PART NO.
BENZ AMG C-COUPE DTM
AUDI RS5 DTM
BMW M4 DTM
BENZ AMG C-COUPE DTM
AUDI RS5 DTM
BMW M4 DTM
PART NO.
BENZ AMG C-COUPE DTM
AUDI RS5 DTM
BMW M4 DTM
PART NO.

Receiver Unit
MRS-540BL
Bind Button
5 wires Servo
MS-1135W
Auxiliary Port
(3 Pin)
(Reserved)
XT60
Battery
Connector
Bullet
Connector
Carisma MRS-540BL Receiver Unit
Receiver (RX) Section
2.4GHz 2 Channels receiver
Compatible with Carisma 2CH FHSS radio, (eg. CTX-2710, CTX-2810, CTX-8000)
(Please refer "Binding Flow Chart")
540 BRUSHLESS
MOTOR
Bind
Button
Antenna Cable
Remarks :
The mounting positions of receiver and antenna
cable greatly aect the operating range.
Install the Co-axial antenna vertically to the ground.
Auxiliary Port (3 Pin)(Reserved)
Steering Port : Where to plug in the servos or use
as LED port.
Bind Button : Synchronize transmitter and receiver.
Select frame rate.
Warning :
• Never bend the metal pins on the PCB of receiver.
• Never cut the antenna cable.
• Install the antenna vertically as shown in the figure.
• Keep the antenna as far away from the motor,
ESC and other noise sources as you possibly can.
Tips :
• Wrap the receiver with something soft, such as
foam rubber, to avoid vibration. If there is a chance
of getting wet, put the receiver in a waterproof
bag or balloon.
1. PRESS and HOLD the BIND key of
Receiver unit
NOTE: IF BINDING PROCESS FAIL, REPEAT FROM STEP 1 AND TRY AGAIN.
Receiver Unit Features
ESC Section
Programmable (Please refer to page x “ESC Setup Flow Chart”)
• Programmable Battery Type: NiHM or LiPO
• End Points Calibration
• ESC mode
- Forward / Reverse with Smart Brake
- Forward Only with Brake
Thermal Protection
Stall Protection
Over and Under Voltage Protection
LED indicator
• Just after Power ON
SEARCH RECEIVER : CREEN LED FLASH
RECEIVER CONNECTED : GREEN LED SOLID ON
• Normal Operation
Neutral: BLUE LED Solid ON (Forward / Reverse with Smart Brake)
Flashing BLUE LED (Forward Only with Brake)
Forward (NOT Full Speed): RED and BLUE LED OFF
Forward (Full Speed): RED LED ON and Blue LED OFF
Reversing (NOT Full Speed): RED and BLUE LED OFF
Reversing (Full Speed): BLUE LED ON and RED LED OFF
Brake: RED and BLUE LED ON
Auxiliary Port (3 Pin)
(Reserved)
5 Wires Servo Port
Integrated Servo controller, Standard 5 wire / Option 3 wire servo port / LED Port
When unit is just Power ON, it will check whether a 5 wire servo MS-1135W is connected
or not. If servo MS-1135W is connected, the 3 wire port will become Brake LED port
(Only Carisma LED set can be used for this port). Else, the 3 wire port will become 3 wire
servo port.
Binding Flow Chart
MS-1135W
COMPLETE COMPLETE
4. WAIT the Receiver and the Transmitter’s GREEN LED are both Soild ON,
the binding process is completed.
1. PRESS and HOLD the FTN key on
the transmitter
3. Release the FTN key.
1. PRESS and HOLD the BIND key of
Receiver unit
2. Power ON the unit, GREEN LED
Flashes
3. Release the BIND key, GREEN LED
Flashing waiting for transmitter
to bind.
2. Power ON the transmitter, GREEN LED
flashes, the transmitter is
communicating with the Receiver Unit
ITEM NO. PRODUCT NAME
15339
15340
15343
15363
15345
15347
15348
15437
15438
15440
15441
15443
15371
15373
15374
15376
15378
14986
14139
14104
14103
14994
15239
15349
15350
15352
15354
15355
15356
15357
15358
15364
15362
15370
14130
14131
14129
15224
14114
15015
15369
15444
15379
15367
15368
15278
GT10RS MERCEDES-AMG C-COUPE DTM 2014 (WHITE) CAR BODY PAINTED AND DECORATED BODY
GT10RS MERCEDES-AMG C-COUPE DTM 2014 (RED) CAR BODY PAINTED AND DECORATED BODY
GT10RS MERCEDES-AMG C-COUPE DTM 2014 (RED) CLEAR CAR BODY
GT10RS MERCEDES-AMG C-COUPE DTM 2014 (WHITE) CLEAR CAR BODY
GT10RS MERCEDES-AMG C-COUPE DTM 2014 WHEEL ASSEMBELED (PAIR)
GT10RS MERCEDES-AMG C-COUPE DTM 2014 CAR BODY PLASTIC PARTS + REAR BUMPER SET
GT10RS MERCEDES-AMG C-COUPE DTM 2014 FRONT BUMPER SET
GT10RS RTR BMW M4 DTM 2014 ( WHITE ) CAR BODY PAINTED AND DECORATED BODY
GT10RS RTR BMW M4 DTM 2014 CAR BODY PLASTIC PARTS + REAR BUMPER SET
GT10RS RTR BMW M4 DTM 2014 ( WHITE ) CLEAR CAR BODY
GT10RS RTR BMW M4 DTM 2014 WHEEL ASSEMBELED (PAIR)
GT10RS RTR BMW M4 DTM 2014 FRONT BUMPER SET
GT10RS RTR AUDI RS5 DTM 2014 ( RED) CAR BODY PAINTED AND DECORATED BODY
GT10RS RTR AUDI RS5 DTM 2014 CAR BODY PLASTIC PARTS + REAR BUMPER SET
GT10RS RTR AUDI RS5 DTM 2014 (RED) CLEAR CAR BODY
GT10RS RTR AUDI RS5 DTM 2014 WHEEL ASSEMBELED (PAIR)
GT10RS RTR AUDI RS5 DTM 2014 FRONT BUMPER SET
WHEEL HEX/DRIVE PIN SET
SPUR GEAR 72T
REAR HUB SET
FRONT HUB/STEERING ARM SET
HINGE PIN BRACE SET
INPUT GEAR SHAFT SET (F/R)
GT10RS FRONT SHOCK ASSEMBLED (PR.)
GT10RS REAR SHOCK ASSEMBLED (PR.)
PINION GEAR 24T
GT10RS FRONT DOG BONE PAIR
GT10RS REAR DOG BONE PAIR
GT10RS DIFFERENTIAL OUTDRIVE SET
GT10RS OUTDRIVE
GT10RS THREAD ROD SET
GT10RS SUSPENSION PIN SET
GT10RS SLIPPER SET
GT10RS DIFF. GEAR SET
BALL BEARING 4X10X3 AND 8X12X3.5
BALL BEARING 5X11X4
LOCK NUT (4MM AND 3MM)
BODY CLIP SET (S/M/L)
STEERING POST SET
METAL MAIN DRIVE SHAFT FOR METAL DIFFERENTIAL GEAR
GT10RS MERCEDES-AMG C-COUPE DTM 2014 LED ASSEMBLE
GT10RS RTR BMW M4 DTM 2014 LED ASSEMBLE
GT10RS RTR AUDI RS5 DTM 2014 LED ASSEMBLE
MRS-540BL SERVO + RECEIVER +ESC UNIT
SERVO MS-1135W
GT10RS SERVO SAVER SET
RECEIVER CONNECTION AND INSTALLATION SPARE PARTS LIST
GREEN LED FLASHING
GREEN LED SOLID ON
GREEN LED FLASHING
GREEN LED
FLASHING
GREEN LED
FLASHING