Carr Sportsman Amp User manual

CARR AMPLIFIERS
OWNER’S MANUAL
Revised 23 February 2012

ii

1
Sportsman Instructions
Thank you for purchasing a Carr Sportsman amplifier. The Sportsman fuses the insistent
purity of ‘60s American 1x10 reverb-style amps with the more aggressive dual 6V6 power
section of the late ‘50s yielding enhanced sonic span and control. Tones ranging from clear
and snappy to Texas pushed twang to intercontinental grind are all under the hood of the
Sportsman. Please take time to familiarize yourself with this manual.
Volume – Adjusts the loudness and drive of the amplifier.
Treble – Varies the top end from dark to bright.
Mid – Varies the midrange frequencies and is very interactive with the Treble control. For a
60s American tone, set the Mid to 10 o’clock. The tone becomes more aggressive as you
advance the Mid past 1 o’clock. When the Mid is set near full, the Treble control’s effect is
more subtle.
Bass – Varies the low end from lean to full. To retain clarity, turn the Bass down at higher
volumes.
Reverb – Controls the amount of reverb sound from none to deep and lush.
Headroom – The interface between the pre amp and the power amp on the Sportsman. For
the cleanest sound, set the Headroom to Max and set the Volume control low. For thicker
clean tones, set the Headroom to 11 o’clock and the Volume to 12 o’clock. For overdriven
tones, set the Volume to 3 o’clock or higher and set the Headroom to the desired listening
level. Higher Headroom settings will bring in more output section overdrive when the
Volume is set high.
Standby – Set the amp to Standby (switch baton down) before turning on the power switch
(see On-Off-On below). After 1 minute of warm up, switch the Standby baton up. The amp
is ready to be played. Using the Standby switch every time the amp is turned on will prolong
tube life.
On – Off – On – Selects between two ON positions and the OFF position (middle). The two
ON’s are wired in opposite phase of each other. If you receive a shock from another piece of
equipment (a microphone or another amp) that is not properly grounded, or if you hear
static, switching to the opposite ON may solve the problem. This is sometimes called
“switching polarity”.

2
Bottom Panel
Fuse –In the unlikely event that a tube fails, the Sportsman is protected by a 1.5 Amp slow
blow fuse for 120v and 100v (North America and Japan) models or a 0.75 Amp slow blow
fuse for 220v and 240v (Europe and Asia) models. Please consult us or a qualified tech for
assistance in the event of a fuse blowing. The fuse is located on the bottom of the chassis by
the power cord.
Speaker output jack – The speaker output jack is located between the 3rd and 4th pre amp
tubes on the chassis (see Chassis Diagram). The Sportsman is designed to drive a 16 ohm
load. Maximum power and tone will be realized when connected to a 16 ohm speaker or
cabinet. The speakers in Sportsman combos and extension cabinets are configured to
provide the amplifier with a 16 ohm load.
The Sportsman will work with an 8 ohm cabinet with the following caveat - you will lose a
little power from the impedance mismatch and the power tubes will have to work a bit
harder and thus age faster. This effect though is minimal.
To run an external cabinet, turn the Sportsman OFF, unplug the internal speaker (combo
amps) and plug in the external cabinet’s speaker cord. Alternatively, a “Y” speaker cord can
be used to run a 16 ohm external cabinet along with the internal speaker(s) of a combo amp
without damage to the amp (the total impedance or speaker load in this case will be 8 ohms
– see the previous paragraph).
Damage will result from operating the Sportsman without a speaker load.
Biasing your Sportsman
The Sportsman utilizes a mix of cathode bias (self bias) and fixed bias and as such does not
require a bias adjustment when changing tubes. Please use well-matched pairs of output
tubes for maximum performance. The Sportsman can only use matched pairs of 6V6 power
tubes.
Carr Amplifiers selects and tests the finest current production tubes specifically for each
amplifier model. Caution should be used when buying replacement tubes from any dealer
who does not have a return policy as all tubes can have problems (NOS tubes are
susceptible to microphonics and failure too).

3
Recommended Settings
Sound Volume Treble Middle Bass Reverb Headroom
60s American Clean
Thick BF
Low Volume Grind
Texas Overdrive

4

5
Important Reminders
Please keep the original packing materials in case your amp
needs to be shipped for service.
When inserting power
tubes, the power tube key
must line up with the tube
socket keyway.
Do not insert power tubes
with missing or damaged
keys or pins.
When inserting preamp
tubes, the tube pins must
line up with the tube socket
holes.
Do not insert preamp tubes
with missing or damaged
pins.
To reduce the risk of electric shock, keep the unit away from
excess moisture.
No user serviceable parts inside.
Potentially lethal voltage present.

6
CARR AMPLIFIERS WARRANTY
All Carr amplifiers are warranted to be free from defects in workmanship (solder
joints, hardware assembly etc.) for the lifetime of the original owner, and free from
defects in materials (including cabinet) for three years from the date of purchase by the
original owner, provided that:
The owner mails the signed warranty registration card (next page) and a copy of the
original sales receipt to Carr Amplifiers within thirty days of purchase.
Problems are not the result of misuse, abuse, tampering, circuit modification, improper
tube installation (incorrect orientation of tubes can damage the amp), or spilled
beverages, as these will void the warranty.
The amplifier is shipped to Carr Amplifiers in the original packing materials with freight
paid by the purchaser. We pay the return shipping after the warranty work is complete.
Tubes, speaker(s), and reverb tanks carry a ninety-day warranty, and are subject to
the same terms and conditions as above.
Please call us at 919-545-0747 if you have a warranty claim. Be prepared to provide the
model and serial number of your amp. We will issue a Return Merchandise Authorization
number (RMA#) before the amplifier is shipped for service.
For customers outside of North America, warranty and repair service is provided through
the dealer where the amp was purchased.
Shipping address:
Carr Amplifiers
23 Rectory St., Suite E
Pittsboro, NC 27312
Mailing address:
Carr Amplifiers
433 W. Salisbury St.
Pittsboro, NC 27312
Tel: [phone]
Fax: [phone]
www.carramps.com
[e-mail]