Carromco 752.69 User manual

Quality Family Games
Model 752.69
Basketball Instructions
Visit www.carrom.com to register your product to receive the latest product
updates, special offers, and other product related information.
Product Registration
752.69 08/14/14

Part List for Duel Basketball Game
Pipe 1
2 Pieces Pipe 8
2 Pieces
#1 #8 #14
Support Bar
1 Piece
#2
Pipe 2
2 Pieces
#3
Pipe 3
2 Pieces
#4
Pipe 4
1 Piece
#5
Pipe 5
1 Piece
#6
Pipe 6
2 Pieces
#7
Pipe 7
2 Pieces
#9
Pipe 9
1 Piece
#10
Pipe 10
2 Pieces
#11
Pipe 11
2 Pieces
Hinge 12
2 Pieces
#12
#13
Pipe 13
1 Piece
#15
J Hook
2 Pieces
#16
Chute
1 Piece
#17
Backboard
1 Piece
#18
Hoop with Net
2 Pieces
#19
Support Plate
2 Pieces
1

#20
60mm Bolt
2 Pieces
#21
Electronic Scorer
1 Piece
#22
Basketballs
6 Pieces
#23
Pump
1 Piece
#24
35mm Bolt
14 Pieces
#25
20mm x 5mm Bolt
4 Pieces
#26
20mm x 6mm Bolt
8 Pieces
#27
45mm Bolt
4 Pieces
#28
40mm Bolt
2 Pieces
#29
1/8” x 3/4” Screw
8 Pieces
#30
Flat Washer
30 Pieces
#31
Lock Nut 31
30 Pieces
#32
Lock Nut 32
4 Pieces
#33
Wrench
1 Piece
#34
“L” Wrench
1 Piece
#35
Power Pack
1 Piece
#36
Plastic Foam Block
1 Piece
2
Part List Continued

31
30
30
2
24
3
24
2
20
30
31
9
4
6
8
7
7
68
9
3
Step 1
Connect pipes #4 with #3 on each side -
push buttons should lock. Connect pipes
#6 and #3 using bolts #24, washer #30,
and lock nuts #31. Connect pipes #8 and
#9 together. Connect pipes #6 and #9
using bolts #20, washer #30, and lock nuts
#31. Add pipe #2 to pipe #3 (push button
lock), then connect pipe #7 and pipe #8
(push button lock). Connect pipes #7 and
#2 using bolts #24, washer #30, and lock
nuts #31. Repeat on other side of game.
3

4
Step 2
Attach pipes #10 into bracket of pipe #6
(use end of tube with two holes close to
end and bolt into hole at very end) using
bolt #28, washer #30, and lock nut #31.
Attach pipe #11 to other end of pipe #10
using bolt #24, washer #30, and lock nut
#31. Attach hinge #12, with hinge folding
upward, to pipes #10 and #11 using
bolt #24, washer #30, and lock nut #31.
Hinges should attach to outside edge of
game. Repeat on other side of the game.
6
10
12
11
11
12
10
31
24
30
28
30
31
19
17
18
26
Step 3
Attach the rims #18 to the front
of the backboard using bolts #26,
support plates #19, washers #30,
and lock nuts #31 as shown.
Assemble nets to rims.

5
Step 4
Connect pipes #5 and #2 using bolt #24,
washer #30, and lock nut #31. Slide pipes
#1 and #2 together. Attach the backboard
#17 to pipes #1 and #2 using bolt #27,
washer #30, and lock nut #31 through the
two top holes on backboard. Attach
J hook #15 and backboard together using
bolt #27, washer #30, and lock nut #31 in
bottom holes.
1
17
2
3
4
4
3
31
27
5
2
24
30 30
15
31
1

6
Step 5
Attach electronic scorer #21 to the back of
the back of backboard #17 using bolt #25
and lock nut #32. Screw the sensors into
the back of the backboard using
screws #29. Make sure the sensors with
the “Top” sticker go in the top hole and the
sensors with the “Bottom” sticker go in the
bottom hole.
29
17
25
21
32
“Bottom”
(Red Wire)
“Top”
(Gray Wire)
“Top”
(White Wire)
“Bottom”
(Black Wire)
Step 6b
Slide the end of chute #16 over pipe #13
as shown in the diagram below.
16
13
Step 6a
Remove two-sided tape from back of
plastic foam block #37 and attach to back
of backboard above scoring unit. See
diagram on foam block.

7
Step 7
Attach the ends of pipe #13 to both ends of
pipe #11 as shown below. Afx the chute
to the other end of the game near the
backboard as shown in the inset drawings.
Attach velcro strap from chute around pipe
#13.
1
16
13
14
11
2
15

31
24
14
8
Step 8
Attach the support bar #14 over the chute
and on outside end of pipe #13 using
bolts #24, washer #30, and lock nuts #31
as shown below.

To secure the unit upright when not in
use, simply fold the unit up by folding
the hinge #12, lift up bar #10, secure
clevis pin lock by inserting the pin into
the bracket hole then through the second
hole on the pipe and then through the
bracket hole.
9