Carson SC-550-10 User manual

SC-550-10
REMOTE
SIREN AMPLIFIER / LIGHT CONTROL
INSTALLATION AND OPERATING
INSTRUCTIONS
5451 N. Rural Street
Indianapolis, IN 46220
Phone: [phone]
Fax: [phone]
Website: www.carsonsirens.com
Carson
MANUFACTURING COMPANY, INC.

Page 2SC-550-10 Installation and Operating Instructions
4/30/03 CP4818A
TABLE OF CONTENTS
GENERAL DESCRIPTION..............................................................................3
SPECIFICATIONS ..........................................................................................3
INSTALLATION..............................................................................................4
SAFETY PRECAUTIONS ............................................................................4
UNPACKING..............................................................................................4
OPTION SWITCHES...................................................................................4
ELECTRICAL CONNECTIONS....................................................................5
MOUNTING................................................................................................7
RADIO VOLUME ADJUST...........................................................................7
OPERATION..................................................................................................8
GENERAL..................................................................................................8
SIREN CONTROLS ....................................................................................8
Power Switch / PA Volume......................................................................8
Rotary Function Switch...........................................................................8
PA.........................................................................................................8
Siren Button and Auxiliary Siren Input......................................................8
Horn Ring Cycler (HRC)..........................................................................8
Cutout....................................................................................................8
LIGHT CONTROLS.....................................................................................9
Slide Switch...........................................................................................9
Slide Switch Reverse..............................................................................9
Automatic Siren......................................................................................9
Auxiliary Output Switches........................................................................9
Legends.................................................................................................9
SERVICE .....................................................................................................10
PROBLEMS .................................................................................................10
PARTS.........................................................................................................11
RETURN......................................................................................................11
LIMITED WARRANTY...................................................................................11
INSTALLATION INFORMATION....................................................................12
NOTICE
Due to continuous product improvements, we must reserve the right to change any specifications and information,
contained in this manual at any time without notice.
Carson Manufacturing Co., Inc. makes no warranty of any kind with regard to this manual, including, but not lim-
ited to, the implied warranties of merchantability and fitness for a particular purpose.
Carson Manufacturing Co., Inc. shall not be liable for errors contained herein or for incidental or consequential
damages in connection with the furnishing, performance, or use of this manual.

SC-550-10 Installation and Operating Instructions Page 3
CP4818A 4/30/03
GENERAL DESCRIPTION
The SC-550 Remote Siren Amplifier with integrated Lighting Control is a premium unit designed
for single or dual 100W speaker use. A remote hand control is connected to the amplifier with a
thin cable. A 6-position rotary switch controls the primary operating modes of Phaser, Yelp, Wail,
Manual, Horn and Radio. A siren button and auxiliary siren input is provided for control of the
output tone, depending on the rotary switch setting. An integral microphone provides PA function.
The power switch is combined with the PA volume control. A hole is provided in the amplifier to
adjust Radio volume. A 4-position progressive slide switch controls primary lighting and may
automatically activate the siren. Non-progressive slide switch outputs provided for tailored light-
ing. Four auxiliary output pushbuttons provide for controlling additional lighting or other devices.
A latching siren cutout input is provided for connection to a door switch, etc. to disable the siren
when exiting the vehicle. An 8-position DIP switch on the amplifier allows selection of various
options: Two-Tone to replace Phaser, Phaser disable, Horn disable , short Manual, and Horn Ring
Cycler (HRC). Auxiliary siren and cutout input activation polarity along with disabling automatic
siren and slide switch reverse are additional options. The hand control is backlighted with LED's
for night visibility. The siren amplifier utilizes short circuit, high voltage, and reverse polarity pro-
tection systems for maximum service life over a wide temperature range. The slide switch and
auxiliary outputs are fused individually.
SPECIFICATIONS
Siren Amplifier
Input Voltage 11 -16 VDC (negative ground)
Input Current 8 AMPS (@14 VDC -single 100W speaker)
16 AMPS (@14 VDC -dual 100W speakers)
Standby Current Less than 200 ma
Audio Frequency 200Hz -10 kHz +3db
Audio Distortion Less than 3% (@1 kHz -single 100W speaker)
Audio Output 40 watts (@14 VDC-single 100W speaker)
Audio Input 400 ohms+10%
Output Power 105 WATTS RMS MAX. (15 VDC-single 100W speaker)
180 WATTS RMS MAX. (15 VDC-dual 100W speakers)
Siren Frequency 700Hz -1500Hz (Two-Tone and Horn = 435 & 585Hz)
Tones / Cycle Rates Horn Wail Yelp Phaser Two-Tone
Cycle Rates 109 CPS 13 CPM 190 CPM 15 CPS 60 CPM
High Voltage Prot. 16 -18 VDC will cause siren output to cease, resume at normal
Short Circuit Current 50 AMPS (supply circuit must be capable of supplying this)
Operating Temp. -15° F to +140°F
Controls 6-position rotary mode switch (Phaser, Yelp, Wail, Manual, Horn and Radio).
Momentary push-button Siren switch.
PA volume with Power switch on Hand Control, Radio volume on Amplifier.
Auxiliary input connection programmable for positive or negative activation.
Cutout input connection programmable for positive or negative latching cutout opera-
tion.
Connections
(10-Pin Conn.) (2) Negative, (2) Speaker, (2) Radio, Cutout, Auxiliary Siren, (2) non-progressive slide switch outputs (500mA Max. per output)
Note: positive siren connection is through high current input
Light Controls
Voltage 11 -16 VDC (negative ground)
Controls 4-position progressive slide switch with automatic siren activation
(4) auxiliary pushbuttons
High Current Input (2) pressure terminals, 140 AMPS Max. not including siren input current
Slide Switch Outputs (3) pressure terminals, 20 AMPS Max. per terminal
4 Auxiliary Outputs (4) pressure terminals, 20 AMPS Max. per terminal
General
Size Hand Control: 2-3/4" Wide, 1" Deep, 6" High
Amplifier: 7-1/2" Wide, 6-3/4" Deep, 2-1/8" High
Weight 5-1/2 LBS.

Page 4SC-550-10 Installation and Operating Instructions
4/30/03 CP4818A
INSTALLATION
Proper installation of the unit is essential for years of safe, reliable operation. Please read all
instruction before installing the unit. Failure to follow these instructions can cause serious dam-
age to the unit or vehicle and may void warranties.
SAFETY PRECAUTIONS
For the safety of the installer, vehicle operator, passengers and the community please observe
the following safety precautions. Failure to follow all safety precautions and instructions may
result in property damage, injury or death.
Qualifications -The installer must have a firm knowledge of basic electricity, vehicle electrical
systems and emergency equipment.
Sound Hazards -Sound levels produced by attached speakers can cause permanent hearing
loss. Never operate this unit without adequate hearing protection for you and others in the area.
(OSHA 1910.95)
Hand Control Location -Locate the hand control for easy access by the vehicle operator. DO
NOT locate in air bag deployment area.
Amplifier Mounting -DO NOT mount in air bag deployment area. Assure clearances before
drilling in vehicle.
Wiring -Use wiring capable of handling the current required. Make sure all connections are tight.
Route wiring to prevent wear, overheating and interference with air bag deployment. Install and
check all wiring before connection to vehicle battery.
Testing -Test all functions after installation to assure proper operation. Test vehicle operation to
assure no damage to vehicle.
Keep These Instructions -Keep these instructions in the vehicle or other safe place for future
reference. Advise the vehicle operator of the location.
UNPACKING
Inspect contents for shipping damage. If found alert carrier immediately. Contents should in-
clude hand control, amplifier, removable pressure connector, and these instructions. Contact
supplier immediately if any components are missing.
OPTION SWITCHES
Various options can be controlled by turning on or off any of 8 DIP switches on the amplifier.
Switch 1 On: Positive Cutout Input Polarity -Cutout is normally activated with nega-
tive input. This switch changes to positive activation.
Switch 2 On: Positive Auxiliary Siren Input Polarity -Auxiliary siren is normally acti-
vated with negative input. This switch changes to positive activation.
Switch 3 On: Two-Tone -Two-Tone replaces Phaser function.
Switch 4 On: Phaser Disable -The Phaser and Two-Tone function are disabled.
Switches 3 & 4 On: Horn Ring Cycler option (HRC) -This option allows selection of Wail,
Yelp, Phaser and Standby by repeatedly tapping the Siren button, horn
ring or other switch connected to the auxiliary siren input. It also provides
Horn operation by pressing and holding the switch or ring.
Switch 5 On: Horn Disable -The Horn function is disabled.
Switch 6 On: Short Manual -The Manual function can be set to immediately cut off
when the Siren button is released.
Switch 7 On: Automatic Siren Disable -The Automatic Siren feature associated with
the slide switch may be disabled.
Switch 8 On: Slide Switch Reverse -The progressive slide switch normally activates
L1 output in position 1 and L1, L2, L3 outputs in position 3. Setting this
option on activates L1, L2, L3 outputs in position 1 and L1 output in posi-
tion 3.

SC-550-10 Installation and Operating Instructions Page 5
CP4818A 4/30/03
ELECTRICAL CONNECTIONS
(2) #18 AWG
(#16 -2 SPKR)
2 -SPKR -Connect for
same phase (+ to +)
SPKR →
→
SPKR →
→
OUT2 →
→
OUT1 →
→
RAD →
→
RAD →
→
AUX →
→
CUT →
→
NEG →
→
NEG →
→
••••••••••
Auxiliary Siren Input #22 AWG (See next page)
Cutout Input #22 AWG (See next page)
(2) #22 AWG
Connect to output
jack, terminals or
speaker of radio
#14 AWG
Use second lead
for 2 -SPKR
RADIO
Positive Supply
Use both terminals
#6 AWG Max. Wire Size
Each Terminal
(140A Max. Input Current)
(Not including siren amp)
-BAT
+
10-PIN CONNECTOR
Slide Switch Non-Progressive Output 1 #22 AWG (500mA Max.)
Slide Switch Non-Progressive Output 2 #22 AWG (500mA Max.) RELAY
RELAY
LIGHT CONTROL OUTPUTS
20A Fuse for Siren Amp
LOAD LOAD LOAD LOAD
Each Light Output Protected with 25A Fuse
Slide Switch
Progressive Outputs
(20A Max. per Output)
LOAD LOAD LOAD
Auxiliary Outputs
(20A Max. per Output)
Recommended
Wire Size
Amps Size
5 -10 #16
10 -15 #14
15 -25 #12
25 -40 #10
40 -60 #8
60 -80 #6
Use next larger size
if longer than 10 ft.
Radio
Volume
DIP
Switch

Page 6SC-550-10 Installation and Operating Instructions
4/30/03 CP4818A
ELECTRICAL CONNECTIONS
Connections are made using pressure terminal connectors. Legends on the unit identify each
terminal function. Attach leads by stripping 3/8", inserting into connector and clamp by tightening
screw. Make sure the screw is tight and the wire can't be pulled out. Failure to adequately
tighten the screw can result in improper operation or burning the connector and wire.
Positive Supply: Due to the high current nature of this unit, an appropriate supply line is
required. In addition to the high current delivered to devices on the out-
puts, the siren amplifier will require peak currents up to 50 amps for ade-
quate short circuit protection and reliable operation. The preferred source
is directly at the vehicle battery.
Negative Supply: The negative supply line is for the siren amplifier. The siren amplifier will
require peak currents up to 50 amps for adequate short circuit protection
and reliable operation. The preferred source is directly at the vehicle bat-
tery.
Speaker: Both connections must be used. Two speakers may be connected in par-
allel. Observe polarity (phasing) for maximum sound output.
Radio (Optional): Both connections must be used. The input is isolated and polarity is not
important. May need to adjust RADIO VOLUME on side of amplifier.
Auxiliary Siren
(Optional): The auxiliary siren input allows activation of the Siren button with an exter-
nal source. The OPTION SWITCH determines polarity of activation.
Cutout (Optional): The cutout input turns off any siren tone when activated, and remains off
until a siren control is changed. The OPTION SWITCH determines polarity
of activation.
-VDC
switching
example
ADDED
DOOR
SWITCH
CUT
+VDC Switching
Example
DOOR
SWITCH
+VDC
CUT
SPLICE DOME
LIGHT
+VDC Switching examples
HORN
RING
SWITCH
+VDC
AUX
SPLICE HORN RING
SWITCH
+VDC
Added
SPDT
Switch
HORN
HORN
-VDC
switching
example
MOMENTARY
FOOT
SWITCH
AUX

SC-550-10 Installation and Operating Instructions Page 7
CP4818A 4/30/03
L1, L2, L3 Outputs: These outputs are controlled by the slide switch in a progressive fashion.
Outputs are fused.
S1 to S4 Outputs: These outputs are controlled individually by pushbutton switch 1 to 4.
Outputs are fused.
OUT1,2 Outputs
(Optional): Controlled by the slide switch in a non-progressive fashion.
See Slide Switch under Light Controls.
These outputs are not fused and are intended to control external relays.
When turned on the output supplies +VDC @ 500mA max.
When turned off the output is open (high impedance).
MOUNTING -Hand Control
Choose a mounting location convenient to the operator and away from any air bag deployment
areas. Consider cable routing to amplifier as well as PA use. Mount the hand control with sup-
plied Hook and Loop tape. If the tape method is not preferred, the hand control may be mounted
several ways including a cell phone holder. Plug cable into amplifier, no other electrical connec-
tions are necessary.
MOUNTING -Amplifier
Select a location for the amplifier in an area such as the driver compartment firewall, under a seat,
etc. Mounting the amplifier in the engine compartment or in an area directly exposed to weather
is not recommended. Assure adequate ventilation to prevent overheating. Allow clearance for
wiring and radio adjustment. Inspect behind mounting area for clearance. Mark the location of
the mounting holes to be drilled.
Drill 4 holes (up to 1/4" diameter) to mount the amplifier to the vehicle. Install the removable pres-
sure connector and make all electrical connections before final mounting (See ELECTRICAL
CONNECTIONS). The connector may be secured with the two locking screws. Then mount the
amplifier to the vehicle using appropriate hardware (not supplied).
RADIO VOLUME ADJUST
If the Radio repeat mode of the siren is going to be used then the RADIO VOLUME control may
need to be adjusted. This is a one time setting which depends on the radio connected and its
normal volume. On the hand control, set the slide switch to OFF, set the rotary switch to RADio,
and power switch to ON. With the volume on the radio itself set to normal level, set the RADIO
VOLUME control to the desired output level.

Page 8SC-550-10 Installation and Operating Instructions
4/30/03 CP4818A
OPERATION
GENERAL
This unit is designed for easy operation under the stress associated with high-speed pursuit.
Most functions are accessible with one simple motion without repetitive activation of switches or
automatic timed switching that can interfere with desired operation.
SIREN CONTROLS
The combined power switch and volume control give power to the
hand control and adjust the PA volume. Power is turned OFF by
rotating the control counterclockwise until it “clicks”. Power is turned
ON and increased PA volume by rotating clockwise. The power
switch should be turned off when vehicle is not being used to con-
serve battery power.
The Rotary Function Switch selects various siren operating modes.
These modes are as follows:
PHaSeR: The siren produces a very fast warble tone. This mode
may be used at intersections or in highly congested ar-
eas. Horn and PA override available in this mode.
YELP: The siren produces a moderate warble tone. This mode
may be used in lightly congested areas. Horn and PA
override available in this mode.
WAIL: The siren produces a normal rise-fall tone pattern. This mode may be used on high-
ways or areas with constant traffic flow. Yelp and PA override available in this mode.
MANual: The siren rise-fall tone is controlled manually with the Siren button. PA override avail-
able in this mode.
HORN: Also considered a standby mode. Horn and PA override available in this mode.
RADio: This mode reproduces, or repeats, the output of a radio. The radio must be connected
and the RADIO VOLUME adjusted. PA override available in this mode.
The following OVERRIDE FUNCTIONS are available for certain modes.
PA: By pressing the microphone PTT (Push to Talk) switch
on the side of the hand control, the siren will change to a
PA (Public Address) amplifier. The siren mode resumes
when the PTT is released. Adjust the PA Volume and
hold the MIC close to your lips for proper operation. PA
override is available in all modes.
HORN: By momentarily pressing the Siren button or activating
the auxiliary siren input, the HORN tone is produced.
The siren mode resumes when released. Horn override is available in all modes ex-
cept Radio and Wail.
YELP: Only available in Wail mode. By momentarily pressing the Siren button or activating
the auxiliary siren input, the siren output is toggled between Wail and Yelp tone.
HRC: Horn Ring Cycler is only available in Horn (Standby) mode and must be enabled with
the option switches. By repeatedly tapping the Siren button or auxiliary siren input,
the siren output is cycled from Standby to Wail, Yelp, and Phaser tones. It also pro-
vides momentary Horn override by pressing and holding the Siren button or auxiliary
siren input. If automatic siren is active, then Standby is skipped.
CUTOUT: The cutout input turns off any siren tone when activated, and remains off until a siren
control is changed.
PA and Siren Button
PTT
Power Switch/PA Volume
Function Switch

SC-550-10 Installation and Operating Instructions Page 9
CP4818A 4/30/03
LIGHT CONTROLS
A 4-position slide switch provides control of primary lighting functions. It also provides automatic
activation of the siren. Four pushbuttons for additional lighting or controlling other devices. The
power switch on the hand control mustbe ON for light controls to function.
Slide Switch
The slide switch provides progressive (additive) control of lighting
functions. Position 1 turns on L1 output. Position 2 turns on L1 and
L2 outputs. Position 3 turns on L1, L2, and L3 outputs. Position 3
also turns on the siren (Automatic Siren).
The slide switch position outputs OUT1 and OUT2 are for setups
that require a non-progressive slide switch. Only Position 1 will turn
on OUT1. Only Position 2 will turn on OUT2. In Position 3 the L3
output can be used since only Position 3 will turn this on.
Note that OUT1 and OUT2 are not fused and intended to drive external relays. These outputs
can only drive loads up to 500mA each.
Slide Switch Reverse
The Option Switch can be set to reverse the slide switch positions. Position 1 and Position 3
operations are reversed or swapped.
Automatic Siren
Position 3 of the Slide Switch (or 1 with Slide Switch Reversed) provides Automatic Siren. If the
siren controls are set where there is no siren tone output, the Automatic Siren will override with
Wail. The only exception is PA Override or Cutout activation.
Automatic Siren may be disabled with the Option Switch.
Auxiliary Output Switches
Four pushbutton switches are provided for various other lighting
functions or device control. Legends above the switch light up
when the switch is on.
Legends
Different legends may be selected to match the device controlled
by aux output switch. A sheet of stick-on legends is supplied.
Select the legend and place centered over the legend area. Press down on the legend to stick
over clear window and tuck under rubber framing. Gently lift up on the sides of rubber framing to
help cover the edges of the legend.
To remove a legend, use a thin edge to gently push rubber frame aside and pry between legend
and clear window. Try not to puncture clear window. The stick-on adhesive is strong.
Blank (black) legends are provided for aux output switches with no function. The white back-
ground legends may be written on with permanent marker to create custom legends.
Slide Switch Position Slide Switch Reverse OFF
OFF L1, L2, L3, OUT1, OUT2 ALL OFF
1L1, OUT1 ON
2L1, L2, OUT2 ON
Slide Switch Reverse ON
L1, L2, L3, OUT1, OUT2 ALL OFF
L1, L2, L3 ON (Auto Siren)
L1, L2, OUT2 ON
3L1, L2, L3 ON (Auto Siren) L1, OUT1 ON
Slide Switch
Auxiliary Output Switches
Legend Label
Legend
Area
1Rubber Frame
Clear Window

Page 10 SC-550-10 Installation and Operating Instructions
4/30/03 CP4818A
SERVICE
This unit is designed to provide years of reliable service under even the worst conditions. Many
times there may appear to be a problem with the unit when the true problem is in the speaker(s),
controlled devices, or improper installation. The following chart shows typical symptoms and
possible causes.
A blown siren fuse doesn't necessarily mean that the unit is bad. If a speaker or speaker lead is
shorted the fuse will blow before the unit is damaged. Disconnect the SPKR leads and replace
the 20A fuse. If the siren emits a sound when in the Yelp position it is OK. Check the speaker(s)
or leads for possible shorting.
25A Fuses are required for each light control output. Adequate fuse rating is required to prevent
overheating of the output connection block.
PROBLEMS
Symptom Possible Cause Check
No power Power switch not turned on
Connector or connections loose
Siren fuse blown
Loose connection at power source
Does backlighting come on?
Do you hear a "pop" when turned on?
Is an external fuse or circuit breaker used?
Are the negative leads connected to a good ground?
No siren tone-
PA works High Voltage Protection PA PTT button stuck
Cutout activated
Cutout Polarity Option set wrong
The input voltage must be less than 16 volts.
Does PTT button release properly?
Does the siren work when Cutout input is disconnected?
Is the Cutout Input Polarity option properly configured?
No PA PA volume not set properly Have you tried turning the PA volume control?
Distorted siren
sound Speaker assembly loose Intermittent Aux Input connection
Low vehicle voltage
Is the speaker bell or tip loose?
Is the Aux Siren Input used and wired properly?
The input voltage must be greater than 11 volts.
Intermittent siren
tone High Voltage Protection Connector loose
Bad power connection
PA PTT button activation
Circuit breaker in supply connection
Is the vehicle voltage regulator working properly?
Is the connector tight on the back of the unit?
Is there a loose connection on a power lead?
Is something lying on the PTT button?
Is a circuit breaker used with at least a 50A rating?
Horn function
stuck on or
Manual or Phaser
stuck on
Siren button switch stuck
Aux Siren switch stuck
Aux Input improperly connected
Aux Input Polarity Option set wrong
Does the Siren button switch return fully when released?
Does the Aux Siren switch return fully when released?
Is the Aux SirenInput used and wired properly?
Is the AUX Siren Polarity option properly configured?
No Radio Unit not connected to radio
Radio volume too low Is the radio connected properly to the unit? Can you here the radio in the vehicle?
Have you tried setting the Radio Volume Adjust?
Wrong siren tone Two-Tone option selected Is the Two-Tone option set?
Phaser not work-
ing Phaser disabled Is the Phaser Disable option set?
Horn not working Horn disabled Is the Horn Disable option set?
Manual stops
immediately Short Manual enabled Is the Short Manual option set?
Automatic Siren
not working Automatic Siren disabled Is the Automatic Siren Disable option set?
Light Output not
working Light Control Output fuse blown Internal relay contacts bad Is the light or device shorting? Is the output current limited to 20A?
Light Output stays
on Internal relay contacts fused from overheating Is the output current limited to 20A?
Non-progressive
output not work-
ing
Internal switching transistor bad Is the external relay coil shorting?
Is the output current limited to 500mA?
Slide switch
outputs turn on in
wrong order
Slide Switch is reversed Is the Slide Switch Reverse option set?

SC-550-10 Installation and Operating Instructions Page 11
CP4818A 4/30/03
PARTS
RETURN
If you have any questions concerning this or any other Carson product, please contact our Tech-
nical Service Department at [phone]. Many issues can be handled over the phone. We
can also be reached via e-mail at serv[email protected]
If a product must be returned for any reason, please contact our Technical Service Department to
obtain a Returned Merchandise Authorization number (RMA#) before you ship the product to
Carson. Please write the RMA# clearly on the package near the mailing label. Be sure to provide
a return address, contact and phone number, along with a brief description of the problem.
Part Description
CP4177 Cable, Coil Cord W/Modular Connector (Hand Control)
CP4732 Control, 1K Vertical Trimmer (Amplifier)
F-16SP/12276 Control, 1K PA Volume W/Power Switch (Hand Control)
CP4833-10 Connector, 10-pin Removable Pressure W/Locking Screws
ATO/ATC 20A Fuse, 20 Amp Automotive (Siren)
ATO/ATC 25A Fuse, 25 Amp Automotive (Light Output)
1555 KNOB Knob, Black Selector Switch
CP4895 Label, Aux Output Legends
CP4701 Relay, 40A Light Control Output
CP3902 Switch, Rotary 6-Position Selector
CP4119 Transistor, TIP36C Power
CP4818 Manual, SC-550-10 14 Instruction
CP4652 Cable, Extension for Hand Control
CP4141 Connector, for Extension Cable
LIMITED WARRANTY
Carson Manufacturing Company, Inc. warrants this new product to be free from defects
in material and workmanship, under normal use and service, for a period of five (5)
years from the date of delivery to the first user-purchaser.
During this warranty period the obligation of Carson Manufacturing is limited to repairing
or replacing, as Carson Manufacturing may elect, any part or parts of such product
which after examination by Carson Manufacturing is determined to be defective in mate-
rial and/or workmanship.
This warranty does not cover labor charges for removal or re-installation of the product.
Fuses and lamps are not covered under this warranty.
This warranty does not extend to any unit that has been subjected to abuse, misuse,
improper installation or which has not been adequately maintained, nor to units which
have problems related to service or modification at any facility other than the manufac-
turer.
THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING
BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL CARSON MANU-
FACTURING COMPANY, INC. BE LIABLE FOR ANY LOSS OF PROFITS OR ANY
INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF ANY SUCH DEFECT
IN MATERIALS OR WORKMANSHIP.

Page 12 SC-550-10 Installation and Operating Instructions
4/30/03 CP4818A
INSTALLATION INFORMATION
MODEL: SC-550 _______________________ OPTIONS
SERIAL NO: ___________________________ ______ Two-Tone instead of Phaser
PURCHASE DATE: _____________________ ______ Phaser and Two-Tone Disable
DEALER:______________________________ ______ HRC enabled
______________________________________ ______ Horn disabled
INSTALLER:___________________________ ______ Short Manual
______________________________________ ______ Automatic Siren disabled
INSTALL DATE:________________________ ______ Slide Switch Reversed
Auxiliary Siren Connection ________________ ______ Auxiliary Siren Input Polarity
Cutout Connection_______________________ ______ Cutout Input Polarity
SLIDE SWITCH
L1: _______________________________ OUT1: ________________________________
L2: _______________________________ OUT2: ________________________________
L3: ________________________________________________________________________
AUXILIARY OUTPUTS
S1: _______________________________ S3: ________________________________
S2: _______________________________ S4: ________________________________