Cary Audio Design CAD-280 SA V-12R User manual

Cary Audio Design
CAD-280SA
V-12R
Vacuum Tube Stereo or
Monobloc Power Amplifiers
OPERATION MANUAL
NOTE: Before installing your new V-12R power amplifier, please read this manual carefully as it will
inform you of the specifications, proper installation procedures and operation procedures. Also included
in this manual are guidelines on how to properly service and care for your new CAD-280 SA (V-12R)
stereo or mono power amplifier.

Specifications for your newV-12R power amplifier.
We have updated the V-12 mono and stereo models to a RACING (R) version! The
new racing input circuit makes the input sensitivity 1.2 volts, similar to most
components currently available. Operating the power amplifier is a simple procedure.
Each unit is designed for long term stability in virtually any home operating situation.
Please note, if the unit is operated outside the parameters outlined in this owner's
manual, damage may result. Please read this manual carefully before putting your new
V-12R in operation. The following definitions are applicable. Warnings should be
followed explicitly.
1.2 Specifications
The CAD-280 SA V-12R or V-12R Monobloc version basic specifications:
DIMENSIONS: 9’’H x 12 _’’W x 20’’D
WEIGHT: 68-lb. stereo or 85-lb. for the Monobloc version
CIRCUIT TYPE: Push-Pull Triode or Ultra-linear Amplification in Pure Class A
POWER OUTPUT: 50 watts – Triode Mode 100 watts – Triode (Mono)
100 watts – Ultralinear Mode 200 watts – Ultralinear (Mono)
INPUT SENSITIVITY: 1.3 volts for full output
INPUT IMPEDANCE: 150,000 ohms
NOISE AND HUM: > 84db below rated output
FREQUENCY RESPONSE: 20Hz to 23Khz +/- 1.0 dB (at full power)
TUBES: 2- 12BZ7 Input tubes (or 12AY7, 12AX7)
2- EL-84 Current Source tubes (or 6BQ5)
12- EL-34 Output tubes (or 6550, KT-66, KT-77, KT-88, KT-
90, 6L6)
POWER TRANSFORMER: 1- EI laminated, 200% duty cycle
OUTPUT TRANSFORMERS: 2-EI laminated stereo (1-EI mono) Silicon Impregnated
RESISTORS: 1.0% tolerance, precision metal film resistors
CAPACITORS: Oil Filled
POWER SUPPLY CAPACITORS: 4 - 560 MFD @ 400 volts
AC CORD: 3 conductor shielded detachable
AC POWER REQUIREMENTS: 117/234 volts AC 50/60Hz
POWER CONSUMPTION: 420 watts in operation, 10 watts in stand-by
WARM-UP TIME: 3 minutes
BREAK-IN PERIOD: 100 hours of music playing time
FINISH: Jaguar Carnival Red paint on chassis
FRONT PANEL: Machined, Black Anodized aluminum
Specifications are subject to improvement without notice or obligation.
WARNING
HAZARD PRESENTS PERSONAL INJURY OR DEATH
Caution
EQUIPMENT DAMAGE MAY OCCUR BUT NOT PERSONAL INJURY
Note
Proper performance of the amplifier cannot be ensured
if disregarded

1.3 Front Panel Features
POWER ON/OFF SWITCH: AC mains switch and high voltage in “ON” position
HV LED: Indicates the high voltage supply is ON and the fuse is intact.
BIAS L led: Indicates the Bias voltage for Left channel (Left chassis side for Mono)
BIAS R led: Indicates the Bias voltage for Right channel (Right chassis side for Mono)
OPERATE/STANDBY SWITCH: Turns filaments on in the “OPERATE” position.
1.4 Rear Apron Features
INPUTS RCA or XLR: Signal input connection via shielded interconnect cable
RCA/ XLR SWITCH: Switches between RCA and XLR input selection.
SPEAKER OUTPUT: Three- 5-way binding posts provide the signal output to the
speaker system. Red = +, 4 or 8 ohms, Black = -, ground
BIAS JACK: _” ‘phone plug’ jack for supplied cable with plug to measure the output
tube bias levels. See tube bias instruction sheet later in the manual.
BIAS POTENTIOMETER: Adjusts to achieve the bias level setting for the output tubes.
AC: 3- conductor shielded power detachable cord to AC power mains.
POWER AC FUSE: This is an over current protection fuse for the power transformer.
Never replace with any other fuse than 3 AMP SLOW BLOW!
250 VOLT! (2 AMP SLOW BLOW IN 220 VAC OPERATION)
FILAMENT FUSE: This is an over current protection fuse for the filament transformer.
Never replace with any other fuse than a 2 AMP SLOW BLOW!
(1 AMP SLOW BLOW IN 220 VAC OPERATION.)
LEFT AND RIGHT TUBE (side) FUSE: This is a protection fuse for the output tubes.
Never replace it with any other fuse than a 0.5 amp fast blow! 0.5A @ 250 volt rating.
1.5 TOP PANEL FEATURES
TRIODE / ULTRA-LINEAR SWITCHES: Three mode switches per chassis side allow
you to choose from 50 watts (100 watts mono) power in Triode mode or 100 watts
(200 watts mono) power in Ultralinear mode. All mode switches should be set to the
same ‘direction.’
RED LED: (‘Good Health LED’) Indicator for each individual output tube. When the
LED is lit it shows that the associated output tube is working.
CAUTION
EQUIPMENT DAMAGE MAY OCCUR WITH IMPROPER RATED FUSES
CAUTION
NEVER REMOVE or THE INSERT AC LINE CORD WHEN THE UNIT IS ON TO
AVOID RISK OF ELECTRICAL SHOCK

INSTALLATION
This section describes the unpacking and installation procedures for the CAD-280 SA
amplifier.
2.1 Unpacking
All shipping containers have been specifically designed to protect their contents and
special care has been taken to prevent damage under normal shipping conditions.
Mishandling should be evident upon inspection of the shipping container. If chassis
damage is found after a visual inspection, take care not to destroy the evidence. If
necessary, document the damage with photographs and contact the transport carrier
immediately. Carefully remove your new power amplifier from its packing carton, and
examine it closely for signs of shipping damage. It is recommended to save all the
original packing cartons to protect your amplifier from damage should you wish to
store it or ship it for after-sales service.
2.2 Warranty Card
Fill out the enclosed warranty registration card and return it to Cary Audio Design, Inc.
within 15 days of original purchase. Keep your original sales slip from your Cary Audio
Authorized Dealer with the packing cartons should you ever need it. Failure to register your
warranty will set the limited warranty time period to 90 days from date of purchase. When
purchased from a Cary Audio Authorized Dealer and properly registered, the limited
warranty period is extended. See the limited statement of warranty for details.
2.3 Amplifier Placement
In general, the location of your new V-12R is not critical. Certain precautions must be
taken to ensure optimum performance however. Always avoid extremely hot locations
such as near steam heat radiators or other heating units. Allow 10-12 inches above the
amplifier for proper ventilation. Keep the top of the amplifier clear of books, paper or
other equipment to protect it against overheating! DO NOT place your amplifier in a
closed book case - overheating will damage the amplifier!
2.4 Power Requirements
The CAD-280 SA is designed to operate from house current AC mains. The design
voltage is 117 VAC at 50/60Hz. (Foreign units 234 VAC at 50/60Hz.)
2.5 Cables
WARNING!
MAKE NO ATTEMPT TO PUT THE CAD-280 SA AMPLIFIER IN
SERVICE WITHOUT THE BOTTOM PLATE ATTACHED -
CONTACT WITH HIGH VOLTAGE INSIDE THE CHASSIS CAN BE
FATAL!

The speaker cables from the output posts of the CAD-280 SA to the speaker system
can be any convenient length your set-up requires. Select speaker cables of sufficient

size to preserve the outstanding performance capabilities of your power amplifier.
Heavy gauge #14 wire is suitable for distances up to 15 feet, #12 wire for up to 30 feet.
Your Authorized Cary Audio Dealer will have proper speaker cable in stock for this
purpose.
Signal input connection is made via the input jack(s) on the rear of the CAD-280 SA.
The interconnect cable(s) from the output of a variable output CD player or
preamplifier can be any convenient length your set-up requires. The choice of a
shielded, high quality interconnect cable is important. Once again, your audio dealer
will suggest and have the proper cables in stock for this purpose.
3.1 Operation
Your new power amplifier is ready for operation after the speaker, interconnect cables
and the vacuum tubes have been installed into their proper sockets. Refer to the tube
placement sheet at the end of this manual for proper tube installation. On the
amplifiers rear panel please select either the RCA or XLR input(s), according to your
installation.
3.2 4 or 8 OHM Speaker Binding Posts
Select the proper speaker binding post (4 or 8 ohm) for the speaker(s) in your system.
The selection should be based on your current speakers’ rated specifications and
listening tests to confirm the correct connection.
3.3 Triode or Ultra-Linear Mode Switches
Select either the “Triode” 50 (100 Mono) watts or “Ultra-Linear” 100 (200 Mono)
watts output setting. Make sure all six switches are set to the same operating mode
position. You can switch between the operating modes while playing music at a
moderate volume level. Flipping one mode switch at a time is OK.
3.4 Power ON and Standby Operate Switches
Flip the power switch to the “On” position and then flip the standby switch to the
“Operate” position. Observe that all 16 vacuum tubes are lit, after a delay of 10-15
seconds. When the power tubes start to conduct, red ‘Good Health’ LED’s on the top
panel will light up next to each one. This might take 30-45 seconds delay.
3.5 The Break-In Period
The tubes, capacitors and output transformers take approximately 100 hours use to
settle in for peak performance. The V-12R will sound good right out of the box but it
will improve within a short time. After the first 50-100 hours you will notice increased
depth and tighter bass. This break-in period defies engineering theory perhaps, but we
believe it is true with quality audio amplifiers.

3.6 Bias Measurement
The bias is factory preset. It is a good idea to measure it during the initial setup to make
sure it is set to the specifications provided at the end of this manual. The AC voltage
may be different from one area to the next. Follow the instructions provided. (250-275
mA is the recommended bias setting range, per side, with 220 mA being the minimum
suggested bias level setting) Make certain to set the test meter used to mA range.
SERVICE AND CARE
4.1 CAD-280 SA (V-12R) Care and Cleaning
The case and front of the amplifier may be cleaned with a soft cloth and Windex or a
window cleaner. Moisten the cleaning rag; do not get the amplifier wet. The relative
frequency of cleaning will be governed by the operating environment cleanliness. The
chassis is best polished with non-abrasive car wax.
4.2 Tube Replacement
If it becomes necessary to replace the tubes in the amplifier, a matched set of output
tubes of the same name brand should be used. A new tube kit is available from Cary
Audio. You should get a few years or more from the output tubes with everyday usage
and many years of use from the smaller 12BZ7 and EL-84 tubes. Other types of output
tubes may be used in the V-12R power amplifiers; 6L6, 6V6, KT-66, KT-88, 6550C, KT-
90, KT-99 or EL-34 tubes are all acceptable for use in the output stage.
4.3 IN FACTORY SERVICE
Careful consideration has been given to the design of your V-12R amplifier to keep
maintenance problems to a minimum. However, it is possible that some problems may
arise which cannot be cured by a vacuum tube substitution. At this point we suggest you
contact our Customer Service Department phone number [phone] to describe
your problem in detail. DO NOT return the amplifier to the factory without a return
authorization number (RMA) from the Customer Service Department. Please always
use the ORIGINAL PACKING BOXES from Cary to ship your amplifier for moving or
for service. Cary Audio Design, Inc. will assume no responsibility if the transportation
or shipping company refuses to pay a damage claim due to your improper packing or
lack of insurance should the unit be lost or damaged in shipment.
All mentions of in factory service are relevant for Cary Audio Design products purchased
and used exclusively within the USA only. Non USA distributors of Cary Audio Design
products will establish their own local warranty or after service policies. Ask your
dealer about local warranty policies in your locale, if you reside outside the USA.
WARNING
MAKE SURE AMPLIFIER IS UNPLUGGED FROM AC MAINS BEFORE
SERVICING

! PLEASE OBSERVE THE SAFETY DIRECTIONS IN THIS MANUAL TO
AVOID POSSIBLE ELECTRICAL SHOCK OR EQUIPMENT FAILURE
DUE TO IMPROPER INSTALLATION!
Cary Audio Design
1020 Goodworth Drive
Apex, North Carolina 27539
Tel: [phone]
Fax: [phone]
www.caryaudio.com
[email protected]
WARNING!
MAKE NO ATTEMPT TO PUT THE CAD-280 SA IN SERVICE WITH THE
BOTTOM PLATE REMOVED. CONTACT WITH THE HIGH VOLTAGES
FOUND INSIDE THE CHASSIS CAN BE FATAL!
COMPLETELY REMOVE AC POWER PLUG FROM THE WALL AND
ALLOW 30 MINUTES FOR THE HIGH VOLTAGE CAPACITORS TO
DISCHARGE THROUGH BLEEDER RESISTORS BEFORE ATTEMPTING
TO CHANGE TUBES OR CLEAN THE INSIDE OF THE AMPLIFIER.
CAUTION
NEVER REMOVE OR INSERT AC PLUG WHEN THE UNIT IS ON OR
THE AC POWER SWITCH IS IN THE ON POSITION. OBSTRUCTION
OF THE TOP PORTION OF THE CAD-280 SA WILL RESULT IN TUBES
OVERHEATING AND DAMAGE TO THE AMPLIFIER.