Casa Bonita K066 User manual

Floor Lamp with Shelving
K066 v02: 19/11/21
Please read and retain these instructions for future reference
ASSEMBLY INSTRUCTIONS / INSTRUCTIONS FOR USE:
Unpack the components carefully. Please check all parts have been removed from the packaging.
Parts
Dimensions
(H) 159 x (W) 26 x (D) 26cm
Weight: 4.2kg
Length of mains lead: 3m
•PLASTIC AND WOOD WITH FABRIC SHADE
•BULB REQUIREMENT –LED BULB
Technical details
220-240V AC
50/60Hz
60W
1x LED bulb(E27, Max 60w, 220-240V - (not included)

Floor Lamp with Shelving K066 Instructions for Use
Please read and retain these instructions for future reference v002:19/11/21
Step 1.
Holding bottom board (3) upside down, insert four
screws (2) through the holes in the four corners
and tighten into four long poles (4) so that the
screw heads are recessed into the bottom board
(3), place round the cushions (1) to cover the four
holes, turn this completed section right-side up.
Screw four double sided screws (5) into top of the
four long poles (4). Place first shelf board (6) onto
four protruding double-sided screws (5).
Step 2
Screw four long poles (4) onto the protruding
double-sided screws (5). Screw four double-sided
screws (5) into the top of the four long poles (4).
Place second shelf board (6) onto four protruding
double-sided screws (5).
Step 3
Screw four long poles (4) onto the protruding
double-sided screws (5). Screw four double-sided
screws (5) into top of the four long poles (4). Place
lamp holder board (7) onto four protruding double-
sided screws (5). Attach the lamp holder to this
lamp holder board (7) by inserting the base screw
of the lamp holder through the lamp holder board
(7) and securing it with the wing nut (14)
underneath the lamp holder board (7).
Step 4
Screw four short poles (8) onto the double-sided
screws (5). Place top frame (9) onto the four poles;
Insert four screws (2) through the holes in the four
corners and tighten into four short poles (8), so
that the screw-heads are recessed into the top
frame (9). Place small plastic caps (10) into
recessed holes in the four corners.

Floor Lamp with Shelving K066 Instructions for Use
Please read and retain these instructions for future reference v002:19/11/21
•To switch on the light, pull the cord (15). Note: if the cord is difficult to operate from its original hole,
feed the cord through one of the other 3 holes.
Cleaning and Maintenance
•Unplug the lamp before cleaning.
•Use a clean, dry, soft, lint-free cloth.
•Do not use water or other chemical cleaning agents.
Step 5
Insert the four small plastic anchors (12) into the
small holes near the corners of the lamp holder
board (7). Unfold fabric shade (11) and place
through the top frame (9) down onto the lamp
holder board (7) outside of the four small plastic
anchors (12). Use plastic cord clips (13) to secure
the electric cord to the poles along the side. See
diagram below:

Floor Lamp with Shelving K066 Instructions for Use
Please read and retain these instructions for future reference v002:19/11/21
PLUG WIRING (UK & IRELAND)
This appliance is fitted with a BS 1363 3-amp plug. If you have to replace the fuse, only those that are ASTA
or BSI approved to BS1362 and with a rated current of 3-amps should be used. If there is a fuse cover fitted,
this cover must be re-fitted after changing the fuse. If the fuse cover is lost or damaged the plug must not be
used. Spare fuse holders and fuses are available from electrical outlets. If the socket outlets in your home or
office are not suitable for this product’s plug, the plug must be removed and disposed of safely. Attempts to
insert the plug into the wrong socket is likely to cause electric hazard. A replacement plug should be wired
according to the following instructions:
The cable
A mains electricity cable contains two or three inner wires. Each has a core of copper and an outer layer of
flexible plastic. This product is earthed; the wires in the cord set are colour coded in the following way:
BLUE NEUTRAL
BROWN LIVE
GREEN & YELLOW EARTH
The diagram shows the key features of a correctly wired
three-pin mains plug.
DISPOSAL
•Coopers of Stortford use recyclable or recycled packaging where possible.
•Please dispose of all packaging, paper, cartons, packaging in accordance with your local
recycling regulations.
•Plastics, polybags –this is made from the following recyclable plastic.

Floor Lamp with Shelving K066 Instructions for Use
Please read and retain these instructions for future reference v002:19/11/21
Code & Symbol
Type of Plastic
Polyvinyl Chloride
Polypropylene
PP, PA46
Commonly used for
Pipes, construction
material, flooring,
windows, guttering, plister
packs
Microwaveable food
containers, yoghurt pots,
butter tubs, disposable
plates and cups
CD’s, crisp packets, various
flexible packaging, baby
bottles, sunglass lenses
Notes
Not usually colellected
from household recycling
bins, Sometimes recycled
at local waste
management centres.
Commonly recycled and
collected from household
recycling bins (packaging
tape itself not recyclable
but does not interfere
with cardboard)
Not often or widely
recycled
•At the end of the product’s lifespan please check with your local council authorised household waste
recycling centre for disposal.