Casa CTL-DCM User manual

2012 CASA
http://www.casa-laserlight.com
CTL-DCM
Manual

Troubleshooting
If the power supply indicator doesn't light up and the laser doesn't work, please check the
Unpacking
power supply and the input voltage. We will soon lead you into new sense of vision realm a life from now on!
In Stand-Alone operation, if the power supply indicator is light up and sound active Thank you for purchasing this product.Please read user guide for safety and operations infor-
indicator isn't light up, but the laser is shut off doesn't work. mation before using the product. Keep this manual for future reference. This product can create
A. Because sound is too small make for laser shut off in sound active, please increase perfect laser programs and effects since it has passed a series of strictly tests before delivery.
the music volume or increase audio sensitivity with sensitivity knob, please check as below Please check the attachments listed on the page after opening the carton. In the event of carton
B. Please check if unit has been set up in slave mode, then set up in master mode. damage or attachment missing in transit, please contact your dealer or our after sales service
In Master-Slave operation, slave unit don't function, please check as below. department.
A. Make sure to there's only one master in the chain, and the others are set in slave mode.
Attachments
B. Make sure to control the unit without DMX console controlling. 1. Laser Light:1PCS 2. Power Cable:1PCS 3. User Guide:1PCS
C. Make sure to take a good quality power cable and connection.
Notice
In DMX mode operation, the laser is OFF and the DMX signal indicator is unlighted, Do not turn on and off the unit frequently.
please check as below. Do not exposure the human eye direct to laser beam.
A. Make sure to set up the DMX mode. Before using this unit make sure the power supply is ground.
B. Make sure to have a good connection. This unit is intended for indoor use only and should be prevented form water, moisture
In DMX operation, the unit can’t be controlled by the DMX console, but the DMX signal and shake. The working temperature of this unit is 18～30℃, do not use this continuously
indicator is flashing, please make sure the DMX console and unit have the same channel. over 3 hours, otherwise it shortens the lifetime of the unit.
If the output beam direction above isn't the right way, please restart the unit. Use cleaning tissue to remove the dust absorbed on the external lenses periodically to opt-
If the unit is fail, please turn off the unit, then turn on again after 5 minutes. imize light output.
Do not remove or break the warranty label, otherwise it void the warranty.
After trying the above solution you still have a problem, please contact your dealer or Always replace with the exact same type fuse, replacement with anything other than the
our company for service. specified fuse can cause fire or electric shock and damage your unit, and will void your
manufactures warranty.
This lamp laser dangerous grade is a Class III B, eyes directly in observation in danger in-
side the light beam, the minimum irradiation is apart from 15
The AC110V/220V switch please don't turn without authorization, because the user turns
to result in the machine damage by oneself, our company is all irresponsible.
8 1
General instructions

Features
Various working modes
Includes four working modes as DMX, Sound Active, AUTO and Master-Slave Control
for different applications.
Various programs
POWER
The double tunnel laser beam is compages, more than 50 laser patterns, over 200 laser eff-
ects.Different working modes has different program.
DMX control
The unit has 7 channels to control in DMX mode. The unit has BLACK OUT function.
The uint will shut OFF if no DMX512 signal.
Universal DMX Operation (DMX mode)
Master-Slave function
The system allow link many units (as slave unit) together to doing synchro job without co- This mode allows you to use universal DMX-512 console to operate.
nsole in sound active or AUTO mode.
LED indicating and shut-off function Install the units in a suitable position (laying or appending).
In sound active mode, the unit's panel has LED indicating for sound active. The unit will Use standard XLR microphone cable chain your units together via the XLR connector on
shut off after 8 seconds when the music stops. on the rear of the units. For longer cable runs we suggest a terminator at the last fixture.
DPSS Laser Assign a DMX address to each the unit using dipswitches, see the "DMX Address Quick
Use Diode-Pumped Solid State green laser, stable output and long working life. Reference Char".
Turn on the all units' power, the units begins reset, then the unit begins working.
Technical Specification
Use DMX console to control your units.
Voltage: □AC220V/ □110V, 50/60HZ, Fuse: 2A/250V
Rated Power: 30W
Laser
CTL-DG5: 25+25mW(green 532nm)
CTL-DG10: 50+50mW(green 532nm)
POWER
CTL-DC+:Laser Power:30mW Green + 100mW Red + 130mW Yellow + 100mW Violet
CTL-DCP:25+25mW green laser 532nm,80+80+80mW red laser 650nm
Working Modes: DMX, Sound Active, AUTO, Master-Slave
DMX Control Channel: 7 channels
Notes
Graphics & Effects: more than 100 patterns, over 300 effects DMX console can not be used in Master-Slave operation (Sound Active or AUTO mode ).
Interface: 3 pins XLR jack for DMX or Maser-Slave linking There should be only one master unit in Master-Slave operation.
Size
L*W*H=630*225*160mm
Weight:
6.5Kg
2 7
……
1: Master: Sound/AUTO N：Slave
2：Slave
1: DMX Mode N：DMX Mode2：DMX Mode
……
DMX Si
g
nal

Function setting
Uses dipswitches to assign a unit’s function: DMX/slave, or sound active, or AUTO
mode.For the unit is DMX mode, set the DMX address. Each dipswitch represents a
binary value. See the “Function chart”.
Rear Panel Figure
1. Power Jack 2. Cooling Fan Dipswitch #10 is use to set master or slave mode. Master modes have sound active and
3. Audio Sensitivity Knob 4. DMX Signal Indicator: Green AUTO mode.Slave modes have DMX and Slave mode. The units automatically identify
5. Dipswitches: Function Setting 6. DMX or Linking Jack DMX or SLAVE mode by data receives. Dipswitch #9 use to is set sound active or AUTO
7. ON/OFF 8. Sound Active Microphone/ Power Indicator mode in master mode.
DMX address calculation
Operation
For DMX mode, DMX512 address from #1 to 9# dipswitches must be set, the
address is set from 1 to 511. Each dipswitch represents a binary value.
Master-Slave Operation
Dipswitch Value Dipswitch Value
＃11＃632
This mode will allow you to link up to 32 units together without controller. ＃22＃764
＃34＃8128
Install the units in a suitable position (laying or appending). ＃48＃9256
Turn on the all units' power, the units begins reset, then the unit begins working. The slave ＃516 ＃10 Set to "0"
units will react the same as the master unit. One unit has 7 channels, so each unit must be assigns 7 channels at least. We may
Choose a unit to function as Master mode, set dipswitch to select Sound Active or AUTO assign 8 channels for one unit, then DMX address = 8*N + 1, N=0, 1, 2, 3 ……
mode. The others must be set to Slave mode, set dipswitch to select Slave mode. Example
Use standard XLR microphone cable chain your units together via the XLR connector on One loop address=1, two loop address=9, three loop address=17, four loop address=25
the rear of the units. For longer cable runs we suggest a terminator at the last fixture. Loop Address Binary Dipswitches
The units will react to the low frequencies of music via the internal microphone. Adjust the 1 1 100000000 ＃1
audio sensitivity knob on the back of the master unit to make the unit more or less sensi- 2 9 100100000 ＃1+#4
tive in sound active.The panel has LED indicating for sound active. 3 17 100010000 ＃1+#5
4 25 100110000 ＃1+#4+#5
6 3
Function Chart
1
56
2
3
42
7 8

DMX Control
DMX Control Parameter Chart
Close, laser OFF
Sound active mode
AUTO mode
Static patterns of DMX mode
Dynamic patterns of DMX mode
Pattern selection 52 static/dynamic patterns
Position-X Adjust position-X
Position-Y Adjust position-Y
Scanning speed 0 is speedy, 255 is slow
Dynamic pattens 0 is speedy, 255 is slow, has ten
play speed grade speed
Static pattern size 0 is small, 255 is big
There are 52 static patterns, the sizes of the patterns that DMX value is 140 previous are
CH2 Parameter Chart For Function
adjustable,the following irregular patterns are non-adjustable. There are 52 dynamic patter-
ns, whose sizes are non-adjustable.
Front/Rear Panel
1、Laser Aperture One
Front Panel Figure
4 5
tetragon 2
75～79
dot circle roll 160～164 ver-extend line
205～209
100～104 square short sector round 2 230～234
pentagon 4
95～99
many dot 1
250～254 many dot 2
wave line
235～239 wave dot line
240～244
pentagon 1
pentagon 2
pentagon 3
ver-dot line jump 210～214
dot diagonal jump
215～219
vert-flex line
35～39 vert-dot line circle turn 165～169 vert-shrink line
40～44 45° diagonal dot circle turn 170～174
50～54
ladder line 4
tetragon 1V line 2 hori-dot line jump 200～204
185～189
180～184 ladder line 1
circle flash 145～149
65～69 V dot line 1 hori-line jump 195～199
70～74
hori-shrink line
dot circle jump
dot diagonal
135° diagonal
circle jump
30～34 vertical line
80～84 triangle 1
DMX value Static patterns
dot circle 1
15～19 scan circle
20～24 horizontal line
dot diagonal
V dot line 2
V line 1
0～4
dot square
dot circle flash
dot line scan
dot triangle 2 short sector round 1
hor-extend line
dot circle to big 135～139
150～154
140～144
long sector round 1
hori-dot line circle roll 155～159
0～255
Static patterns Dynamic patterns DMX value
circle circle to big 130～134
Channel Function Value
Mode
0～49
50～99
100～149
150～199
CH1
christcross
scan circle to big
CH6 0～255
110～114 rectangle 1
rectangle 2
10～14 dot circle 1
5～9
CH5 0～255
rectangle extend
hori dot line move
vertical line move
200～255
Dynamic patterns
vert-dot line move
ho-flex dot line
hori-flex line
chiasma line
105～109
CH2 0～255
CH3
25～29
CH7 0～255
CH4 0～255
square turn
dot square turn
pentagon turn
dot pentagon turn
Description
125～129
115～119
120～124
90～94 pentagon star turn
bird fly
square dotdot rectangle 2 45° diagonal move 255
dot rectangle 1 line scan
220～224
triangle 2
dot rectangle extend
square extend
dot bird fly
wave flowing
dot wave flowing
many dot jump 1
hori dot line flex
tetragon turn
hori line flex
hori line move
rectangle turn
dot rectangle turn
175～179
ladder line 2
60～64 190～194 ladder line 3
55～59
dot circle to add
scan circle extend
long sector round 2
85～89 dot triangle 1 diagonal jump
ve-flex dot line
45～49
vertical line jump
dot diagonal move
dot square extend
many dot jump 2
square dot jump
spirality line
245～249
225～229
1
111