Case IH AFS Pro 700 Reference guide

AFS AccuControl Liquid Toolbar AFS Pro 700
Quick Reference Card (v28.* and after)
REQUIREMENTS
The following actions are required for proper operation. Working
thru this document in order will properly set up your Liquid
Application system. This guide is to be used as quick reference
only. Insert a data card in the display before turning the display on.
1 – GENERAL NAVIGATION
1.1 Main Screens
2 – SET-UP SCREENS
2.1 Operator
Toolbox>Oper
a) Create an operator.
b) Select preferred units
of measurement.
2.2 GPS Setup
Toolbox>GPS
a) Verify GPS Location
b) Verify Offsets
c) Verify DGPS Type
Main screen
Status/Warnings
Navigation Bar
Left Hand Area
3 – LIQUID TOOLBAR CONFIGURATION 3 – LIQUID TOOLBAR CONFIGURATION – continued
Toolbox>AccuCtrl
Note: Activation is required (Toolbox>Activate)
prior to these steps.
3.1 Basic Setup
a) Select AccuCtrl
Operation [Liquid]
b) Select AccuCtrl
Installed [Yes]
c) Create New Implement
d) Select Implement Type
[Liquid Toolbar]
3.2 Implement Configuration
a) Press ‘Setup’
b) Select Planter Type
c) Select Vehicle Type
d) Set Number of Drive
Sections [A]
NOTE! Section Shut-Off
Valve Control information
entered in 3.3
e) Set Number of Rows [B]
f) Enter Row width [C]
g) Enter Bar Distance
in Inches (axle to
application point) [D]
NOTE! Verify GPS Offset (Toolbox>GPS)
h) Measure Implement Right/Left Offset [E]
i) Enter Rows Per Drive Section
j) Press ‘Done’
NOTE: The next setup steps may or may not be needed.
The configuration of the Liquid Toolbar determines the
need for set-up. If the implement is not equipped with
this capability, leave the setup as ‘No’.
3.3 Section Control Setup
(If equipped with Section Shutoff Valves)
a) Select Section
Control [Yes]
b) Press ‘Setup’
c) Select number of
Control Modules
d) Assign Module Serial
Numbers (starting w/
modules on LH side)
e) Assign Module Rows
Per Section (Number of
Rows per shutoff valve)
f) Select Control Polarity
Note: Active On is common for Section Control Valves.
Active Off is common for LiquiBlock Valves
g) Select ‘Done’
3.4 Liquid Drive Set-up (If equipped w/ hydraulic drive)
a) Select Liquid
Drive [Yes]
b) Press ‘Setup’
c) Verify Number of
Control Modules
d) Select Drive Type
(Servo or PWM)
e) Assign Module Serial
Numbers (starting w/
modules on LH side)
f) Assign Plumbing Type
(Servo only)
g) Enter Drive Pulses/Gal
for each Drive
Note: Pulses/gallon will be found on the liquid ow meter.
Some ow meters are measure in pulses/10 gallons. If this is
the case, divide that value by 10 to nd pulses/gallon.
h) Select Master Valve
i) Select Pump Disarm
j) Select Section Off Behavior (Lock At Last or Turn Off)
k) Press ‘Done’

3 – LIQUID TOOLBAR CONFIGURATION – continued
3.5 Master Switch Box
(If equipped with External Switch Box)
a) Select Master Sw
Box [Yes]
b) Press ‘Setup’
c) Verify Serial Number of
Switch Box
d) Select Footswitch
(if installed)
e) Press “Done’
Note: Rate 1/Rate2/
Manual Switch is not
functional. All others
are functional.
3.6 Implement Switch
(If equipped with Toolbar Mounted Implement Switch)
a) Select Imp
Switch [Yes]
b) Press ‘Setup’
c) Select Imp Switch
Serial Number
d) Select Switch Polarity
Note: Determine by
raising and lowering the
implement and watch the
Implement Status Arrow
in Status/Warning Area
for proper operation.
e)Press ‘Done’
3.7 Section Switch Box (If equipped with
External Section Switch Box or Desire Manual Valve
Section Control through Run Screens)
a) Select Section
Switch Box [Yes]
b) Press ‘Setup’
c) Select Cong Mode
[Auto] or [Manual]
for custom
d) Verify Sw Box
Serial Number
(if equipped w/
external switchbox)
Note: If no external switchbox is installed, User Dened
Windows can be assigned to a Run Screen (Toolbox>Layout).
4 – WORK CONDITION – REQUIRED FOR OPERATION
Work Condition>Layer
IMPORTANT! The settings below are linked to a
work condition. These must be selected or checked
whenever a work condition is created/changed: product type,
application rate, drive settings, product delay (w/ as applied),
product layer control (w/ as applied), and product control.
NOTE! A work condition name could be the current work
practice, crop type (corn, soybeans, etc), seed size, eld
condition, or weather condition, etc.
NOTE! This setup is required for logging/ mapping data and
using Overlap & Boundary Control.
4.1 Preparation
a) Insert a data card in the display
b) Create/select a Grower/Farm/Field/Task and Crop Type
(Performance > Profile)
4.2 Product Setup
Toolbox>Product
a) Name the product
(ex. 32-0-0)
b) Select Form Type for
Product [Liquid]
c) Select Product Usage
d) Enter Default
Application rate
e) Enter Minimum
application rate
& Maximum
application rate
NOTE! Rate will not be able to be adjusted outside of this range.
f) Create additional products (liquid, etc.) as needed.
4 – WORK CONDITION (continued)
4.3 Product Layer Assignment
Work
Condition>
Layer
Assign a product to a control
section of the Applicator.
a) Select/create a work
condition.
b) Select Layer 1
Control Type
[AccuControl Liquid].
c) Select Product for
Layer 1 Control.
d) Assign Additional Layers as needed
4.4 Controller Setup Liquid – (if equipped)
Work
Condition>
Control
a) Verify Implement
b) Verify Work Condition
c) Select Controller [Liquid]
d) Product Delay – Default
2.0 sec.
(see section 7
for Product Delay
Measurement procedure)
e) Enter the Minimum Speed
(if ground speed drops
below this speed, sprayer will apply at this set speed)
f) Enter value for Off-target Alarm Limit
5 – CALIBRATIONS (If equipped with Liquid Rate Control)
5.1 Valve Calibration
Work
Condition>
Valve Cal
Note: Vehicle & controlling
components should be at
normal operating temp/
conditions for these
calibrations.
a) Select Drive Number
to Calibrate
b) Press ‘Start’ for Automatic
Valve Calibration
c) Repeat any other Drives

Record calibration values here, if desired
USAGE CAL VALUE
5 – CALIBRATIONS
(If equipped with Liquid Rate Control) – continued
5.2 Liquid Calibration
Work Condition>Liquid Cal
a) Verify Implement
b) Verify Work Condition
c) Select Liquid Op
Mode – [Liquid]
(Accept Safety
Warning if agreed)
d) Press Master Control –
‘Apply’ Button
e) Press ‘Next’
f) Verify Control Module
Serial Number
g) Verify Meter Cal
Value (change in
Toolbox>AccuCtrl>
Liquid Drive Setup)
h) Enter Simulated
Speed (Typical
Application Speed)
i) Enter Target Rate
j) Prime System
k) Press ‘Next’
l) Place Catch Buckets
Under Each Valve
Section of Applicator
m) Press the ‘Start’
Button & Allow
Product to Flow
n) Manually Measure
Collected Product and
Calculate Total Amount
Applied Across Entire
Width of Drive Section
(in Gal or L)
o) Enter [Actual Output]
p) Press ‘Update’
Button to Update
the Meter Value
q) Repeat if Needed.
6.1 Enable Spraying
Run screens
Note: Most windows will need to be placed on
the run screen (Toolbox>Layout)
a) Liquid Op Mode -
Select [Liquid]
b) Read Safety message &
press ‘Accept’ if agreed
c) Master Control – Press
‘Apply’ on display or
switch on master switch
on switchbox (if equipped)
6 – OPERATION
6.2 Liquid Rate Control (If equipped)
a) ‘Liq Ctrl’ Defaulted to ‘On’
b) Increase or decrease rate, if needed
c) Automatic rate control (prescription) assigned in
Performance>Rx Setup
6.3 Prime Control (If equipped w/ Liquid Ctrl)
Prime is used to ll the system so no gap is left in the
eld when starting.
Note: Window may not be available in v28.* software
versions. If not available, use the start button found in
Toolbox>Liquid Cal to prime.
a) Press the Prime
button for 3 sec.
b) Wait for prime icon
in warning area to
stop ashing
c) System is primed
Current Rate
Exit to
save change
Use Default
Rate
Product
On / Off
Increase
Decrease
7 - OVERLAP/BOUNDARY CONTROL
7.1 Overlap/Boundary Control
Toolbox> Overlap
a) Turn overlap
control on.
b) Turn boundary
control on (requires a
created boundary)
c) Set % for out of
bounds.
d) Set % of overlap
for shutoff.
e) Set start early
distance to 0 ft
f) Set stop late
distance to 0 ft.
IMPORTANT! Product delay must be measured and set
correctly before adjusting start early/stop late values.
7.2 Product Delay Adjustment
Work Condition>Control>Liquid
Before making any adjustments to the
Product Delay, make sure GPS offsets &
Bar Distance are entered correctly.
To check performance:
Note: Prime can be used to perform this calibration (start at step h), but
may not be available on the run screens. The liquid calibration screen
will be used to check the product delay in this case. Instructions below
are for using the liquid calibration method.
a) Select Work
Condition>Liquid Cal
b) Select Liquid Op Mode
– [Liquid] (Accept Safety
Warning if agreed)
c) Press Master Control –
‘Apply’ Button
d) Press ‘Next’
e) Enter Simulated Speed
(Typical Application
Speed)
f) Enter Target Rate and
press ‘Next’
continued on next page

7 - OVERLAP/BOUNDARY CONTROL – continued 7 - OVERLAP/BOUNDARY CONTROL – continued
7.3 Running Overlap/Boundary Ctrl
NOTE! The following windows can be located
on the Run screens.
Disengages drive section master valve
and/or all boom valves for that drive
section. “On” when the button is black
(1), and “Off“ when the button is grey (2)
Quickly switch between Auto
and Manual section control
Enables/Disables Overlap Control
(disable before backing, enable after
driving forward), except AccuGuide
complete tractors
Enables/Disables
Boundary Control
Disengage individual
boom valves
NOTE! (A) must be present for Auto Overlap and Boundary
Control to function. If (M) is present, Auto Overlap and
Boundary control will not work!
AFS-8035-13e Replaces: None
© 2013 CNH America LLC. All rights reserved. Printed in U.S.A.
Case IH is a registered trademark of CNH America LLC. Any trademarks referred to herein in
association with the goods and/or services of companies other than CNH America LLC are the
property of those respective companies.
CNH America LLC reserves the right to make improvements in design and changes in
specifications at any time without notice and without incurring any obligation to install
them on units previously sold. Specifications, descriptions and illustrative material herein
are as accurate as known at time of publication, but are subject to change without notice.
Availability of some models and equipment builds varies according to the country in which
the equipment is used.
Visit us on the web at www.caseih.com
TIPS
1) A data card must be inserted in to the display.
2) Check GPS Offset, Bar Distance, Product Delay, and check that a product is
assigned to a layer for Overlap & Boundary control to function properly.
3) “(A)” must be present in a window for Auto mode.
4) Disable Overlap Ctrl before backing into corners, etc. Re-enable after
moving forward. Turning off Overlap Control before backing up is not
required with tractors that have Case IH Factory AccuGuideAutoGuidance.
7.2 Product Delay Adjustment – continued
g) Press the ‘Start’ button
on the display and at
the same time, start the
stopwatch.
h) Stop the stopwatch
when product is rst
observed leaving the
application point.
i) The elapsed time
displayed on the
stopwatch is the
Product Delay.
j) Exit the calibration
without updating the
calibration number by
pressing ‘Back’.
k) Press ‘Liquid’ Tab
l) Enter the measured time
as the Product
Delay gure.
m) Throughout the season
check for proper
overlap operation
n) If exact measurement of
error is determined use
this formula to convert
this distance to a new
Product Delay (PD).
o) Adjust Start Early/Stop Late distance for intentional overlap.
If a negative number seems to be required for SE/SL, re-
measure & adjust Product Delay
= new PD (sec)
In. of error
mph X 17.52