CashConcepts CCE 410 User manual

CashConcepts
CCE 410
CashConcepts Europe GmbH
Kemptener Straße 99 D –88131 Lindau
Tel. [phone] –Fax [phone] - 20
Email [email protected] –Web www.cashconcepts.cc
Münzzähl- und Sortiermaschine
Coin counter and sorter
Benutzerhandbuch
User Manual

2
CashConcepts
CCE 410
Introduction
Many thanks that you have decided on the CCE 410. This professional coin counter should help you by counting
and sorting big amounts of mixed or sorted coins. You can separate in several steps the different coins from each
other and get the result of counted coins shown on the big display.
The innovative use, the clear result and the acceptance of the Euro coins provide for a short training phase without
trainings or time-consuming installation.
Should you have questions to the CCE 410 counterfeit money detector, we are available to you with pleasure.
Your Team of CashConcepts
Warning
General
Please pay attention that no foreign objects (e.g. paper clips) fall in the machine, these can block the
engines and the sensitive sensors of the machine and damage or destroy them.
Please note that during the countable process no ties, hair or clothes are drawn in to avoid injuries and
damages to the machine.
Electricity supply
Use the device only with the provided net part.
Use no damaged or humid power adapter or power supply lines.
Connect the stream supply not with humid hands.
During the change of the fuse the machine must be completely separated from the stream net to avoid
an electric blow.
Servicing
Always switch the power of during cleaning.
Clean the machine with a dry cloth.
Do not use wet or damp cloth or cleaning products.
Do not spill any liquid or spray chemicals over the equipment.
If any liquid is spilled on it, disconnect the power cable from the supply, remove the battery and contact
your dealer.

3
CashConcepts
CCE 410
Specification of coins
By the two setting wheels you can choose the thickness and the diameter of those coins which should be accepted.
Please note that you always start counting mixed coins with the biggest diameter coins. All other coins will be
rejected to the reject pocket on the right side of the machine.
Euro Coins:
Denomination
1 Cent
2 Cent
5 Cent
10 Cent
20 Cent
50 Cent
1 EUR
2 EUR
Diameter
16,25 mm
18,75 mm
21,25 mm
19,75 mm
22,25 mm
24,25 mm
23,25 mm
25,75 mm
Thickness
1,36 mm
1,36 mm
1,36 mm
1,51 mm
1,63 mm
1,88 mm
2,13 mm
1,95 mm
How to use the 410
The CCE 410 can be easily used by the following buttons:
START/STOP Starts or stops the counting
COUNT/BATCH Here you can set up the stop value for the batch counting by the +1,+10+100,+1000 and
also see the actual result of the batch counting.
ADD/STORE You can use this button to add counting and batch results and to see the last counting
result.
CLEAR Clears the display from the last counting result
+1 Set the batch number from 0 to 9
+10 Set the batch number from 10 to 90
+100 Set the batch number from 100 to 900
+1000 Set the batch number from 1000 to 9999
RD To show the total number of coins counted after the machine powered up.

4
CashConcepts
CCE 410
Operating procedure
Normal Counting
Press COUNT/BATCH key to select normal counting mode. The indicator lights on the key lit and indicates the
activation of this function.
Sorted Coins
Select diameter & thickness knob position according to the coins which should be counted. Place coins into the
coin field and press START/STOP key to start the counting. Coins are transported to the coin hopper and process
at high speed and discharged to the coin bag or coin receptacle. The machine stops after 5 seconds when no more
coin pass the sensor. Press START/STOP to stop the machine at any time.
Mixed Denominations
Select diameter & thickness knob position according to the largest coin denomination. Place coins into the coin
field and press START/STOP key to start the counting. Coins are transported to the coin hopper and process at
high speed. Largest coins are counted and discharged to the coin bag or coin receptacle and all others to the reject
pocket.
Repeat the process until all denomination coins are counted.
ADD function
To accumulate counting results, press ADD/STORE key once. The indicator lamp on the key lit and ensures the
activation of this function. Machine will automatically accumulate every coins are being counted. Release
ADD/STORE key to deactivate this function.
STORE function
This machine allows user to view the last counting result. To view the last counting result on the display follow the
next steps:
1. Press ADD/STORE key. The indicator light on the key lit ensuring the activation.
2. Press RD key. Last counting result will be displayed.
Batch Settings
User can count a bag of coins having a pre-set batch number from 1 to 9999 using 4 numeric keys on the control
panel. Pre-Set batch number is displayed on the batch display.
Press COUNT/BATCH key on the control panel until the lamp n the key is off and batch display shows “P”.
Use 4 numeric keys (+1000, +100, +10, +1) to select any batch number.
After selection of batch value, press START/STOP to start counting and the machine stops automatically when the
counting number reached the batch number. Resume counting next batch by pressing START/STOP key. During
batch counting, you can also accumulate batch-counting results by pressing ADD/STORE key.

5
CashConcepts
CCE 410
Press CLEAR & +1 key simultaneously to cleat the batch number from the display. Selection of batch number must
be done before you start counting.
Memory Recall
This machine allows user to view total numbers of coins counted since the machine powered up. To view the total
counting result on the count display follow the steps below.
The indicator light on the ADD/STORE is off ensuring the deactivation of the function
Press RD key, last counting results will display on the count display, such as [R…….XXXXXX]
Press CLEAR to clear all counting results from the memory.
Error Codes
When powering up the coin counter or during counting a series of error messages may appear on the display.
Error Code
Meaning
Action
Eb0
Coin jamming error. Coins are
jammed near the counting sensor
1. Open side cover and remove jammed coins.
2. Close side cover and press CLEAR key to clear error
message
3. Press START / STOP to resume counting
Ec0
Stop State. A coin is passing
through the sensor without
counting / registering
1. Press CLEAR
2. Press START / STOP
E04
Side cover is not closed tightly or
open.
Close side cover tightly.
Maintenance the CCE 410
This chapter described how to take care of the coin counter, including cleaning and maintenance.
WARNING ! The machine must be off and unplugged from the main socket.
Always switch the power of during cleaning.
Clean the machine with a dry cloth.
Do not use wet or damp cloth or cleaning products.
Do not spill any liquid or spray chemicals over the equipment.
If any liquid is spilled on it, disconnect the power cable from the supply and contact your dealer.

6
CashConcepts
CCE 410
Troubleshooting
This chapter provides steps for resolving some problems that may occur during operation. A list of possible
conditions or failures are address with possible causes followed by proper course of action.
Condition
Possible causes
Action
Abnormal condition after powering
up the machine
Unit is plugged into wrong
voltage area
Power fuse is burned
Power supply board fuse is
burned
Connect with proper voltage
Replace power fuse
Contact CCE - Service
Coin jamming
Improper adjustment of diameter
and thickness know
Adjust diameter and thickness
knob according to coin
denomination
Coins rotate inside the hopper, but
do not discharge
Improper adjustment of thickness
know
Adjust thickness knob to the
next largest thickness position
Motor does not rotate
Loose socket connection
between the power supply
switch and the motor
Damaged or broken connection
wire
Contact CCE - Service
Inaccurate counting results
Loose socket connection
between photoelectrical counter
and microprocessor.
Dirty coin counting sensor
Contact CCE –Service
Clean count sensor

7
CashConcepts
CCE 410
Accessories
Contained accessories
Optional accessories
Manual
Net cable
Cleaning kit
Spare Parts
Technical specification
Power connection: AC 230V / 50/60 Hz
Power consumption: 60-65 W
Operating temperature: 0°C –40°C
Dimensions: 400 x 240 x 185 mm
Weight: 8 kg
Counting speed: 2000 coins per minute
Contact
If it should once have problems with your CCE 410 which you can solve with the help of this manual, then you
please get in contact to us by email and describe the problem, we will get in contact to you as soon as possible
with a proposal for solution for the problem.
[e-mail]
Please retain your purchase documents for warranty claims. Do not remove, cover, damage or
modify in any way the rating plate with serial number on the rear of the unit, otherwise you forfeit
your warranty.
You will find this manual also in other languages on our website www.cashconcepts.cc under the
topic “Download” for free downloading.